Parts for Viking Range VDSC365: Exterior Assembly (View #3) Parts

This panel-mounted indicator light signals oven operation. Replace it to restore clear status feedback when the original lamp fails, stays on, flickers, or is damaged.

• Illuminates on the control panel to indicate the oven is heating or in use
• Common replacement signs: light does not turn on, remains lit when oven is off, flickers/intermittent, or physical damage
• Restores visible status confirmation during preheat, bake, or broil
• Indicator only; it does not control oven temperature or heating

• Disconnect power at the breaker before servicing
• Access the rear of the control panel to remove the old indicator
• Note wire locations; transfer the leads to the new light and seat it fully
• Restore power and test operation before reassembly

This is a top burner knob that is used on oven ranges that were manufactured prior to 2003. A burner knob is what the user turns to adjust the temperature on the burner. This part is manufactured out of a black plastic material and has white lettering on it.A new top burner knob may be needed if the original is cracked, broken, or damaged in any way. If any of the letters wear off of the knob, the user may wish to replace it. If the back of the knob is stripped out and it just spins without activating the range, then it will need to be replaced.This top burner knob is a genuine Viking part and is an OEM part sourced directly from the manufacturer. It is sold individually. This particular top burner knob is compatible with oven ranges that are manufactured by the Viking brand.

This oven select knob is a direct-fit control knob that lets you choose oven functions and modes with a clear pointer and smooth rotation. Replacing a worn or broken knob restores reliable control and appearance. What it does:

• Selects oven cooking modes or functions by rotating to the desired setting
• Provides a clear pointer for accurate position selection
• Replaces cracked, loose, faded, or missing selector knobs
• Restores smooth, positive detent feel when worn knob slips or won't turn

• High-level push-on replacement; align indicator with shaft and press firmly until seated
• Disconnect power to the appliance or turn controls off before servicing for safety
• Verify knob fits the control shaft type and orientation before final installation
• If knob won't engage or control still won't operate, inspect the control shaft or switch.

This replacement thermostat knob provides the user control for adjusting temperature settings on compatible Viking ranges and cooktops. It restores a secure, easy-grip control for precise heat selection and consistent operation. What it does:

• Replaces a worn, cracked, or missing thermostat/control knob to restore normal manual temperature adjustment
• Fits the thermostat/control shaft for a snug, slip-resistant fit when turning
• Helps prevent accidental setting changes with a defined detent/stop feel
• Restores a uniform appearance to the control panel when original knob is damaged

• One black thermostat knob

• Pull the old knob straight off the control shaft; push the new knob onto the splined shaft until fully seated
• Confirm correct orientation and that the knob's index lines up with the control markings
• Disconnect power or follow appliance-specific safety procedures before servicing controls

This toggle switch kit replaces a worn or damaged control toggle to restore reliable on/off control for the affected function. It's a direct-fit replacement designed to match the original switch's form and mounting. What it does

• Replaces a broken, loose, or non-responsive toggle switch that prevents proper control
• Restores reliable electrical contact and user control for the associated function
• Stops intermittent operation, arcing, or loss of control caused by a failed switch
• Useful when the toggle lever is bent, loose, or when internal contacts have failed

• Disconnect power (and gas if applicable) before beginning any service
• Access usually requires removing the control panel or console; keep track of screws and trim
• Verify electrical connections and orientation match the original before final assembly
• If wiring shows heat or corrosion damage, replace wiring

This 1/2" x 1/4" rubber bumper cushions contact points to reduce noise and prevent damage on appliance doors, drawers, and panels. It restores proper cushioning for smoother, quieter operation and helps maintain a snug fit. What it does:

• Absorbs shock where panels or doors meet to reduce rattling and clapping noises
• Prevents metal-to-metal contact that can cause chipping, scratching, or wear
• Helps doors and drawers close more evenly by restoring original spacing
• Commonly used where small, press-fit bumpers have worn, flattened, or fallen off

• One 1/2" x 1/4" rubber bumper

• Press-fit replacement; remove old bumper and press new bumper into the same hole until flush
• No special tools required; use a flat pick or small screwdriver to remove old bumper if needed
• Avoid installing on hot surfaces or near heating elements; let appliance cool before service
• Replace matching bumpers in the same area if others show wear for even performance