Parts for Bosch WFMC6401UC/02: Facia Panel Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This interference capacitor reduces electrical noise and helps protect the appliance's control circuitry from voltage spikes. It's a direct-replacement noise suppressor used where EMI/RFI filtering is required for reliable operation. What it does:

• Suppresses electromagnetic and radio-frequency interference that can affect controls and electronics
• Helps prevent false signals or erratic behavior caused by electrical noise
• Supports stable operation of motors and electronic control boards
• Can reduce audible electrical noise or interference-related symptoms

• Disconnect power at the breaker before inspecting or replacing the capacitor
• Discharge the capacitor and avoid touching terminals; use insulated tools
• Verify wiring match and polarity before connecting

Includes(1)Shipping Bolt,(1)washer,(1)sleeve

The Shipping Bolt is an OEM part for Bosch washing machines. This bolt is designed to secure the washer drum assembly during shipping to prevent excessive movement and potential damage.

Causes of a bad shipping bolt can include stripping, damage to the threads, or loss of the bolt entirely during shipment or installation.

Symptoms of a damaged or missing shipping bolt include:

• Excessive shaking or rattling noises from inside the washer drum
• The drum not rotating properly during wash cycles
• Reduced washing efficiency and improper washing performance

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Screw is an OEM part for Bosch microwave ovens. It is a component that secures the outer casing and front paneling of the microwave. The screw is designed to withstand repeated heating and cooling cycles without loosening or degrading. 

Symptoms of bad screw include:

- The front panel or outer casing becoming loose, detached, or misaligned
- Gaps appearing in the seams or joints of the microwave structure
- The door not sealing properly leading to leaks

Over many uses of the microwave, screws can wear down or strip out from over-tightening during repairs or installations. It is important to replace worn screws to ensure the microwave maintains an intact structure.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

This installation set provides the hardware needed to mount and connect a compatible appliance, helping ensure a secure fit and correct hookups during installation. Designed as the ready-to-use kit installers expect. What it does:

• Provides the mounting and connection hardware used during appliance installation
• Helps prevent loose fittings and reduce leaks caused by improperly secured components
• Useful when original installation parts are missing or damaged
• Supports a proper, stable installation for safe operation

• Follow the appliance's installation instructions and local codes when installing this kit
• Turn off power and water supply before beginning work
• Use appropriate tools and verify all connections are tight and leak-free after installation

2 included - Front load

This replacement foot supports and levels your appliance so it sits steady and operates smoothly. Replace a worn or missing foot to restore proper height, reduce wobble, and help protect surrounding surfaces.

• Supports the base/frame to maintain proper height and alignment
• Provides leveling adjustment so the unit remains stable
• Helps reduce rocking, vibration, and rattling during operation
• Replace if the original foot is cracked, stripped, missing, or won't adjust

• Disconnect power; shut off water or gas supplies if applicable
• Carefully tilt or raise the unit to access the foot location
• Remove the damaged foot and install the new one per design
• Level the appliance front-to-back and side-to-side; verify stability before use

The Lock is an OEM replacement part for Bosch front-loading washers. Securing mechanisms through customized openings prevents loads from rolling freely during spinning, maintaining optimal programmed processes. Reliable retention enhances cleaning consistency.

Causes of a bad lock can involve deterioration of locking pawls or supporting rails over many cycles of engaging and disengaging weekly. Protruding lock parts also risk impact damage from overfilled loads.

Symptoms of a bad lock include: 

• Inability to prevent tub contents from spinning unrestrained   
• Loose articles migrating from their intended placement within  
• Door failures to lock closed fully during active cycles
• Premature component wear transferring vibrations to cabinetry

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Door Hinge is an OEM replacement part for Bosch washing machines. This durable component serves as the pivoting mechanism that allows the washer door to open and close smoothly and securely.

Causes of a bad door hinge include:

• Normal wear and tear over time and repeated use
• Physical damage from impact or mishandling
• Corrosion or loosening of the hinge components

Symptoms of a failing door hinge can manifest as:

• Difficulty opening or closing the washer door
• The door not properly aligning or fitting flush when closed
• Excessive wobbling or instability of the door
• Noises or grinding sounds when operating the door

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore washing machine models.

This replacement mounting screw secures panels, brackets, and small assemblies to restore a snug fit and reduce rattling or loose parts. Ideal when a factory fastener is missing, damaged, or stripped. What it does:

• Fastens panels, trim pieces, brackets and internal assemblies.
• Restores proper alignment and prevents movement or vibration.
• Helps stop rattling, loose trim, or parts that shift during operation.
• Use when an original screw is missing, worn, or has a damaged head.

• Disconnect power (and water supply for water-connected appliances) before servicing.
• Use the correct screwdriver or bit to avoid stripping the head.
• Tighten until secure but avoid over-tightening which can strip threads or crack plastics.

This sleeve is a small guide/bushing used in select Bosch-built appliances. It spaces and supports a moving component to keep it aligned and reduce friction, helping the mechanism operate smoothly and quietly.

• Acts as a bushing/spacer around a pin or shaft to guide motion
• Helps maintain alignment of connected parts
• Reduces friction and wear between mating surfaces
• A worn or missing sleeve can cause wobble, rough movement, or squeaking/clicking noises

• Disconnect power and shut off water before servicing
• Note the sleeve's orientation and seated depth during removal to match on installation
• Inspect the mating pin/shaft and surrounding parts; replace if worn for best fit
• Verify smooth movement by hand before reassembly and testing

The Cover is an OEM part for Bosch washing machines. This part covers and protects the door hinge mechanism, maintaining the sleek appearance of the appliance while preventing dust, lint, and moisture from compromising the hinge's functionality.  

Causes for the need to replace the Cover often stem from physical impacts during loading or unloading, general wear over time, or exposure to harsh cleaning chemicals that can degrade the material of the cover.

Symptoms of a bad Cover include:

• Visible cracks or breakage that can lead to moisture and debris entering the hinge area.
• A loose fit, which may cause noise during operation or interfere with the door's ability to close properly.
• Wear and tear that diminishes the aesthetic appeal of the appliance, making it look outdated or poorly maintained.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This replacement screw secures appliance panels, brackets, and internal components so your unit stays assembled, aligned, and quiet. Replace stripped, missing, or corroded screws to restore a tight fit and help prevent vibration or leaks.

• Fastens panels, trim, brackets, or internal parts in their correct position
• Helps maintain alignment and sealing to reduce noise and potential leaks
• Replaces worn, stripped, rusted, or lost hardware
• Common symptoms: loose or rattling panel/handle, misaligned parts, components shifting

• Disconnect power and, if applicable, shut off water before servicing
• Match the head/size to the original hardware; do not mix lengths across locations
• Start threads by hand to avoid cross-threading; tighten snugly without over-torque
• For plastic or thin sheet metal, avoid overtightening to prevent stripping or cracking

Outer door panel that restores the appliance's exterior and protects internal door components. Replaces dented, scratched, or corroded fronts to improve appearance and help the door close and seal correctly. What it does:

• Replaces the damaged outer face of the door—symptoms include visible dents, deep scratches, or peeling finish.
• Covers and protects internal door components from dirt and moisture—symptoms include rust at the door edge or moisture inside the door cavity.
• Restores consistent door alignment and feel—symptoms include uneven gaps, a door that doesn't sit flush, or difficulty latching.

• Disconnect power to the appliance before beginning any work.
• Use care when handling sheet metal to avoid cuts; wear gloves and eye protection.
• Door removal is often required; retain and reuse original fasteners and gaskets unless damaged.

The Screw is an OEM part for Bosch microwave ovens. It is a component that secures the outer casing and front paneling of the microwave. The screw is designed to withstand repeated heating and cooling cycles without loosening or degrading. 

Symptoms of bad screw include:

- The front panel or outer casing becoming loose, detached, or misaligned
- Gaps appearing in the seams or joints of the microwave structure
- The door not sealing properly leading to leaks

Over many uses of the microwave, screws can wear down or strip out from over-tightening during repairs or installations. It is important to replace worn screws to ensure the microwave maintains an intact structure.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

This flat mounting washer helps secure fasteners and maintain proper spacing on appliance assemblies for stable operation and reduced movement. It's a simple replacement that restores the original fit of bolted connections. What it does:

• Sits under a screw or bolt head to distribute load and protect the mounting surface
• Helps keep fasteners from digging into or deforming adjacent parts
• Restores correct spacing where a worn or missing washer caused looseness
• Can reduce vibration-related noise from loose connections

• Disconnect power and water to the appliance before servicing
• Access the fastener and remove the old washer; note the original orientation
• Reinstall with the replacement washer under the fastener head or nut; start threads by hand to avoid cross-threading
• Tighten securely but avoid over-torquing; inspect surrounding parts for wear

The Tank Spring is an OEM part for Bosch washing machines. It is located within the central support assembly below the washer tub. The spring provides counterbalancing tension to assist the tub during movement and rotation.

Causes can be fatigue from years of use, mineral buildup hindering spring function, or damage such as cracks or breaks in the spring coil.

Symptoms of a bad tub support spring include:

• Excessive vibration or off-balance loads during spin cycles
• Noisy squeaking or grinding sounds from central support area
• Difficulty lifting or rotating the tub for loading/unloading

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This replacement screw restores secure mounting for appliance panels and components so parts sit correctly and don't rattle or shift during use. Simple, direct fit for repairs that need the original-style fastener. What it does

• Secures panels, brackets, or small components to the appliance chassis
• Restores proper alignment and prevents vibration or rattling sounds
• Replaces missing or stripped screws that allow parts to move or hang
• Helps maintain safe operation by keeping covers and guards fastened

• One screw

• Disconnect power to the appliance before starting work
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and seat straight; do not overtighten
• Keep removed hardware organized to ensure all fasteners are returned to their original locations

Spring tank secures and positions an appliance tension spring to maintain proper movement and balance for a door or other moving assembly. Replacing a worn or broken tank restores correct spring alignment and smoother, more reliable operation. What it does:

• Holds the end of the tension spring and keeps it aligned in the assembly.
• Maintains correct spring tension so doors or panels open, close and remain balanced.
• Prevents spring detachment that can cause sudden drops, misalignment or noisy operation.
• Common symptoms of a failing tank: door drops or won't stay open, uneven closing, rattling or banging during movement.

• Disconnect power to the appliance before starting any repair to avoid electrical hazards.
• Support the door or moving panel while replacing the tank to prevent sudden movement or injury.
• Use the OEM part orientation and hardware; inspect the spring and mounting points for wear and replace if scored or damaged.
• Test the door/panel operation several times after installation to ensure correct tension and secure mounting.

The Tub Seal is an OEM part for Bosch washing machines. This part prevents water from leaking from the rear part of the drum where it connects to the machine's other components. This seal is specifically engineered to handle the rigorous environment of a washing machine, dealing with constant exposure to water, high spin speeds, and fluctuations in temperature. 

Causes of deterioration in a tub seal include aging and wear over time, chemical damage from detergents, and physical stress from unbalanced loads or excessive spin speeds. 

Symptoms of a bad Tub Seal include:

• Water leaking from the back of the washer, especially during or after the spin cycle
• Unusual noises such as grinding or squeaking, which may indicate that water has seeped into bearings or other components
• An increase in humidity or wetness around and behind the machine
• Rust or corrosion on nearby metal parts, suggesting prolonged exposure to leaking water

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Outer Tub Seal is an OEM part for Bosch washing machines. This part ensures a watertight seal between the outer tub halves, preventing water leaks during the washing cycle.

Causes for the replacement of the Outer Tub Seal can range from natural wear and tear due to age and frequent usage, to hard water conditions that can degrade the seal material over time. 

Symptoms of a failing Outer Tub Seal include:

• Water leaking from the bottom of the washing machine.
• Unusual noises during the spin cycle, which may indicate water has leaked into the bearings.
• Signs of water damage or rust near the base of the machine.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Door Boot Gasket is an OEM replacement part for Bosch washing machines. It is a critical sealing component that forms a tight seal around the washer door, preventing water leaks and ensuring efficient operation during the wash cycles.

Causes of a damaged or worn door boot gasket include prolonged use, exposure to high temperatures or harsh detergents, or physical damage from improper handling or installation.

Symptoms of a bad door boot gasket include:

• Water leaks around the washer door during operation
• Inefficient water retention or loss of water during cycles
• Potential for mold or mildew growth caused by moisture buildup

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore washer models. 

The Clamp is an OEM component specifically designed for select Bosch front-loading washers. As an adjustable mechanism, it secures tub components within acceptable alignments throughout spin cycles.  

Symptoms signaling the need for a new clamp include:

• Increased vibrations from tub or suspension movements exceeding specifications
• Difficulty starting or uneven spin balance detections by diagnostics sensors  
• Loosened or missing fasteners releasing adjustments subject to shifts

Causes related to fatigue cracks developing over prolonged wash cycles equating to years of use. Submersion in cleaning chemicals may also embrittle synthetic portions more rapidly. 

This OEM Bosch replacement clamp is also compatible with Thermador, Gaggenau, and some Kenmore washers.

The Door Clamp is an OEM replacement part for Bosch front-loading washing machine models. Located internally at the edge of the washer door, it secures the door liner firmly in place.

Causes of a bad clamp include cracks developing from repeated door openings/closings, and deterioration of mounting points from constant vibration feedback stressing plastic fasteners over time.

Symptoms include:

• Excessive door sagging creates gaps for debris/moisture entry
• Noisy rattling or shaking from compromised seal integrity
• Difficulty opening/closing the door smoothly

This genuine Bosch replacement is compatible also with Siemens washers.. 

This front drum motor mounting bushing supports the dryer drum shaft and helps the drum spin smoothly for quiet, even drying. It replaces a worn bearing surface to reduce noise and prevent drum misalignment. What it does:

• Provides a low-friction bearing surface for the drum shaft at the front motor mount
• Helps keep the drum properly aligned during rotation
• Reduces squealing, grinding, or rubbing noises caused by a worn front bushing
• Prevents excess wear on the drum shaft and adjacent components when functioning correctly

• One front drum motor mounting bushing

• Disconnect power before beginning any repair and follow all safety precautions
• Inspect the drum shaft, drum seal, and rear bushing for wear and replace as needed
• Use appropriate tools to remove the old bushing and press or seat the new bushing evenly
• Re-check installation and related components if alignment or noise persists after replacement

The Drive Motor is an OEM replacement part for Bosch washing machines. This powerful motor is responsible for driving the drum rotation during the wash and spin cycles.

A bad drive motor can occur due to electrical faults, mechanical issues, or normal wear and tear over time. Signs of a faulty drive motor include the drum not spinning or agitating, unusual noises coming from the motor, or the washer not starting at all.

Symptoms of a bad drive motor include:

• The drum not spinning or agitating  
• Unusual noises
• The washer not starting  

Replace your faulty washer drive motor with this genuine OEM Bosch part to restore your washing machine. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This rear drum motor mounting bushing supports the motor shaft at the back of the tub, keeping the drum aligned and reducing wear. It restores smooth drum rotation and helps reduce noise and vibration when functioning properly. What it does:

• Centers and supports the motor shaft to maintain proper drum alignment.
• Cushions rotating components to reduce squealing, grinding, or scraping noises.
• Helps prevent excess drum wobble and uneven wear on the tub and bearings.
• Can stop intermittent rubbing or burning smells caused by a worn mounting surface.

• Disconnect power before starting and follow all safety precautions; service panels may have sharp edges.
• Access typically requires removing the dryer/heater assembly and drum.
• Inspect mating surfaces and surrounding components (shaft, bearing, seal). Replace any excessively worn parts to prevent repeat failures.
• Use only OEM-recommended parts and fasteners; do not force or press the part in without proper alignment.

This tub shock absorber helps control drum movement and reduce vibration during spin, keeping your washer stable and quiet. Replacing a worn shock restores smoother operation and helps prevent excess shaking that can lead to noise and wear.

• Damps tub movement to minimize vibration and noise during spin
• Helps prevent "walking," banging, and excessive shaking
• Can contribute to unbalanced loads or longer spin times when worn
• Common fix for thumping sounds and visible drum oscillation

• Unplug the appliance and turn off water before servicing
• Access typically requires removing the front or rear panel
• Support the tub before disconnecting old shock; replace in matched pairs when applicable
• Verify secure seating of pins/fasteners and test for smooth suspension travel

This NTC temperature sensor (thermistor) detects temperature changes and sends a signal to the appliance control so temperature is monitored and regulated accurately. It's a direct-replacement sensing element for temperature-feedback systems. What it does

• Measures temperature and converts it to a resistance signal the control board reads
• Commonly used for temperature regulation and safety control in appliance cycles
• Faulty sensor may cause incorrect temperature readings, erratic cycle behavior, or temperature-related error codes
• Restores accurate temperature feedback when replaced

• One NTC temperature sensor (thermistor) assembly

• Intended for users comfortable with basic appliance repair; disconnect power before starting
• May require panel removal and careful handling of wiring connectors; note connector orientation before disconnecting
• Avoid touching the sensing tip with bare hands or bending the probe excessively

The Laundry Deflector Kit is an OEM part for Bosch washing machines. This kit includes baffles that are installed inside the washer drum. The baffles play a crucial role in improving the washing action by lifting and tumbling clothes during the cycle, which helps ensure a thorough clean and efficient water usage.  

Causes of a bad Laundry Deflector Kit can include physical damage such as cracking or breaking, which can occur from heavy or improper loads. Wear and tear over time from regular use also contributes to baffle deterioration.

Symptoms of a bad Laundry Deflector Kit include:

• Clothes not moving or tumbling correctly inside the drum
• Increased noise during a wash cycle
• Unusual wear or damage to clothing
• Parts of the baffle detaching or missing

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Laundry Deflector Kit is an OEM part for Bosch washing machines. This kit includes baffles that are installed inside the washer drum. The baffles play a crucial role in improving the washing action by lifting and tumbling clothes during the cycle, which helps ensure a thorough clean and efficient water usage.  

Causes of a bad Laundry Deflector Kit can include physical damage such as cracking or breaking, which can occur from heavy or improper loads. Wear and tear over time from regular use also contributes to baffle deterioration.

Symptoms of a bad Laundry Deflector Kit include:

• Clothes not moving or tumbling correctly inside the drum
• Increased noise during a wash cycle
• Unusual wear or damage to clothing
• Parts of the baffle detaching or missing

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This replacement hose connects the dishwasher drain/sump to the drain system, restoring proper water removal and preventing leaks or standing water. It's a direct-fit service part when the original hose is cracked or clogged. What it does

• Carries waste water from the dishwasher sump to the household drain or disposal
• Restores proper draining when a split, collapsed, or clogged hose causes standing water
• Helps stop leaks and puddling that can occur from worn or damaged hose sections
• Maintains correct flow to prevent dishwasher error codes related to drainage

• Turn off power and water supply to the appliance before starting any repair
• Inspect hose routing and clamps; replace any damaged clamps or retainers for a secure seal
• Ensure hose connections are tight and routed without kinks to allow proper drainage

This installation set provides the hardware needed to mount and connect a compatible appliance, helping ensure a secure fit and correct hookups during installation. Designed as the ready-to-use kit installers expect. What it does:

• Provides the mounting and connection hardware used during appliance installation
• Helps prevent loose fittings and reduce leaks caused by improperly secured components
• Useful when original installation parts are missing or damaged
• Supports a proper, stable installation for safe operation

• Follow the appliance's installation instructions and local codes when installing this kit
• Turn off power and water supply before beginning work
• Use appropriate tools and verify all connections are tight and leak-free after installation

The Hot Water Inlet Hose is an OEM replacement part for Bosch washers. It serves as a flexible supply line that delivers hot water from an external water heating hot water heater directly to the washer. This hose plays a key role in optimizing wash performance through consistent delivery of hot water for optimal cleaning and sanitization. 

Causes of a bad hot water inlet hose can include wear and tear over time, repetitive flexing weakening the hose material, mineral buildup restricting flow, or damage due to sharp edges or crushing forces.

Symptoms of a bad hot water inlet hose include: 

• Loss or reduction of hot water during wash cycles
• Decreased cleaning ability from insufficient water heating 
• Visible kinks, cracks, or splits along the hose body
• Leaks or drips at hose connections under the washer

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Cold Water Inlet Hose is an OEM replacement part for Bosch washing machines. It serves as a flexible supply line that delivers cold water from an external plumbing source directly to the washer. This hose plays an important role in providing a balanced mix of hot and cold water flow into the unit.

Symptoms of a bad cold water inlet hose include:

• Fluctuations in water temperature during cycles  
• Issues with certain temperature settings like warm or cold not operating properly
• Visible cracking, kinking, or leaking along the hose body
• No water flow or pressure at the cold supply 

Causes of a failed cold water inlet hose can be mineral deposits clogging the line, natural wear and tear over time, or physical damage from crushing or abrasive surfaces compromising its integrity.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore washing machine models.

The Cold Water Inlet Valve is an OEM part for Bosch washing machines. It is designed to regulate the flow of cold water into the washing machine during the wash cycle. This valve operates based on signals from the washing machine's control board, ensuring the right amount of cold water is provided.

Causes of a faulty cold water inlet valve can include wear and tear over time, clogs or blockages in the valve, electrical issues, or valve failure.

Symptoms of a bad cold water inlet valve may include:

• Insufficient or no cold water flow into the washing machine
• Leaking or dripping water from the valve during the wash cycle
• Inconsistent or inadequate water supply for washing clothes
• Error codes related to water supply or filling

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Note: For the Hot Water Valve, order part number 00422245.

The Hot Water Inlet Valve is an OEM part for Bosch washing machines. It regulates the entry of hot water into the machine, crucial for cycles requiring warm or hot washes. Activated by the machine's control system, this valve opens at the precise moment to allow the correct amount of hot water to mix with the cold, ensuring the selected temperature setting is accurately achieved. 

The causes behind issues with the hot water inlet valve often include sediment build-up from hard water, wear and tear from regular use, or electrical failures preventing the valve from operating.  

Symptoms of a malfunctioning Hot Water Inlet Valve include:

• Water that is too cold 
• No water entering the machine 
• Leaks around the valve area 

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This hose inlet is the molded connection that routes incoming water into the appliance and provides a sealed mating point for the fill hose. It restores proper water flow and helps prevent leaks at the hose connection. What it does

• Directs incoming water from the fill hose into the appliance's water system.
• Provides a sealed connection to prevent drips or leaks at the hose attachment.
• Can cause no-fill or slow-fill symptoms when cracked, clogged, or loose.
• Works with the inlet hose and nearby fittings to maintain correct water supply.

• Turn off power to the appliance and shut off the water supply before starting.
• Inspect and replace any damaged gaskets or clamps when installing this part.
• Hand-tighten fittings, then snug with appropriate tools; avoid overtightening plastic fittings.
• After installation, restore water and power, run a short cycle, and check all connections for leaks.

This flow-through sensor monitors the dishwasher's water flow to help ensure correct water delivery during cycles, supporting consistent wash performance. Replaces a worn or failed sensor to restore proper flow detection. What it does:

• Detects and reports water flow to the control so cycles run with correct water movement
• Can cause wash performance issues or flow-related error codes when faulty
• Helps the appliance regulate fill and wash timing based on measured flow
• Works as part of the dishwasher's water-management system with wiring harness and mounting

• One flow-through sensor

• Disconnect power to the appliance before beginning any service
• Handle the sensor and wiring carefully; observe connector alignment when reinstalling
• Replace only with the identical part number

This T-shaped water hose connector routes incoming water to separate internal hose lines, restoring proper water distribution inside the appliance. It replaces a worn or cracked hose tee to stop leaks and restore flow to internal components. What it does:

• Joins three water lines so water can be directed to multiple internal points
• Stops leaks caused by cracked or damaged tee fittings at hose junctions
• Restores reliable water flow to downstream parts that depend on the split connection
• Prevents hoses from separating at a failing junction

• Turn off and disconnect the appliance from the water supply before servicing
• Inspect hose ends and clamps; replace clamps or seals if worn
• Push hoses fully onto each barb and secure with appropriate clamps
• After installation, restore water and check all connections for leaks

The Hose Clamp is an OEM part for Bosch washers. This clamp secures connecting hoses to direct water flow where needed.

Causes of a bad hose clamp can be wear and tear over time, accidental damage from maintenance or repairs, or degradation of the clamp material from chemical exposure.

Symptoms of a bad hose clamp include:

• Leaks around hose connections
• Loose or detached hoses
• Disrupted water flow impacting cleaning performance

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This fastening ring secures mating appliance components by locking parts in place to prevent movement or separation during operation. It's a simple yet essential hardware piece that helps maintain proper alignment and reliable function. What it does

• Holds mating parts together to prevent wobble, vibration, or dislocation
• Keeps seals and assemblies properly seated to reduce noise and misalignment
• Helps maintain correct component spacing for smooth operation
• Commonly replaced when the original ring is bent, worn, or missing

• Designed for use with compatible OEM assemblies; follow for correct placement
• Inspect mating surfaces and replace any damaged clips, seals, or gaskets before reassembly
• Use proper tools to avoid deforming the ring during installation; do not force into place
• Disconnect power and follow safety procedures before servicing the appliance

Hose-inlet directs incoming water from the household supply into the appliance's inlet assembly to allow normal filling and prevent leaks. Replace a cracked or damaged inlet hose to stop visible leaks and restore proper water fill. What it does:

• Routes water from the home supply to the appliance inlet assembly.
• Stops leaks caused by cracks, splits, hardened or collapsed hose material.
• Can cause slow fill, no fill, or visible leaks at the connection when damaged.
• Used as a replacement part where the original inlet hose is worn or leaking.

• Always shut off the water supply and disconnect power before starting work.
• Drain remaining water from lines and have towels handy to catch residual water.
• Inspect fittings and seals; replace clamps or O-rings if worn to ensure a watertight connection.
• After installation, restore water and power and check all connections for leaks.

This temperature sensor (thermistor) measures internal temperature and sends readings to the appliance control to help maintain proper operation and cycles. It replaces a failed sensor so the control can accurately monitor temperature. What it does:

• Senses temperature and provides a variable resistance signal to the control board
• Helps the appliance regulate cooling/heating cycles and defrost timing
• Commonly associated with incorrect temperature, improper cycling, or temperature-related error codes
• Used wherever precise temperature feedback is required by the control system

• One temperature sensor (thermistor) with attached lead/harness as shown

• Disconnect power to the appliance before accessing or replacing the sensor
• Handle sensor and wiring gently; avoid pulling on the lead or bending the sensing element
• Reconnect connectors fully and route the harness away from moving parts or high-heat areas

The Screw is an OEM part for Bosch microwave ovens. It is a component that secures the outer casing and front paneling of the microwave. The screw is designed to withstand repeated heating and cooling cycles without loosening or degrading. 

Symptoms of bad screw include:

- The front panel or outer casing becoming loose, detached, or misaligned
- Gaps appearing in the seams or joints of the microwave structure
- The door not sealing properly leading to leaks

Over many uses of the microwave, screws can wear down or strip out from over-tightening during repairs or installations. It is important to replace worn screws to ensure the microwave maintains an intact structure.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

This installation set provides the hardware needed to mount and connect a compatible appliance, helping ensure a secure fit and correct hookups during installation. Designed as the ready-to-use kit installers expect. What it does:

• Provides the mounting and connection hardware used during appliance installation
• Helps prevent loose fittings and reduce leaks caused by improperly secured components
• Useful when original installation parts are missing or damaged
• Supports a proper, stable installation for safe operation

• Follow the appliance's installation instructions and local codes when installing this kit
• Turn off power and water supply before beginning work
• Use appropriate tools and verify all connections are tight and leak-free after installation

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.