Parts for Ge GSS25IGNBHBB: Freezer Door Parts

Replacement mounting screw for refrigerator panels, brackets, and internal components. Secures loose assemblies when original fasteners are stripped or missing.

Black door handle for side-by-side refrigerators. Replaces cracked, broken, or worn handles. Direct fit installation on refrigerator door exterior.

Replacement fastener for refrigerator door handles. Secures handle to door with durable metal construction. Needed when original is cracked or broken.

Black door stop for refrigerator fresh food compartment. Replaces broken or missing door stops. Prevents door from opening too far and damaging hinges.

Seals freezer door to prevent warm air entry and cold air loss. Replace if torn, cracked, or causing frost buildup. Confirm fit with your model number.

Replaces a broken or worn freezer door cam closure on side-by-side refrigerators. Installs on the door to control opening range and secure latching.

Replacement dispenser grill recess drip tray for side-by-side refrigerators. Collects spills and overflow in the dispenser area. Replace if cracked or missing.

Ice won't dispense or dispenser flap sticks open? The ice dispenser solenoid controls ice flow. DIY-friendly repair with our install video.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

If your dispenser light stays off or won't turn on, this control board restores proper illumination. Moderate DIY, requires clip release and wiring.

Replace your refrigerator's dispenser housing shield cover if cracked, broken, or missing. This protective cover installs over the dispenser housing.

Ice dispenser door assembly seals the ice chute opening on your refrigerator. Replace if cracked, warped, or the rubber gasket is damaged and leaking air.

Spring that provides closing tension for the refrigerator water/ice dispenser door flap. Keeps the dispenser sealed when not in use. Replace if door hangs open or won't close.

Replacement dispenser door recess crank for refrigerators. Operates the ice/water dispenser door mechanism. Replace if broken, worn, or corroded.

Guides ice from your refrigerator door chute into your glass. Replace if cracked, broken, or missing to prevent stray ice and keep the dispenser tidy.

The Ice Dispenser Paddle Assembly is an OEM part for GE refrigerators. It is a component located inside the ice chute that guides ice cubes from the freezer bin out through the dispenser and into a glass below. 

Symptoms of a bad paddle assembly include:

• Ice cubes remaining stuck in the chute and not dispensing
• Incomplete dispensing with ice falling back into the freezer  
• Blockages or backups occurring in the ice dispenser tube

Causes of a bad paddle assembly can include broken or cracked paddles, mineral buildup inhibiting proper movement, or damage over time like worn-out bearings. 

This part is also compatible with select Hotpoint, RCA, and Kenmore refrigerator models.

Water or ice dispenser not working? This dispenser switch activates when you press the lever. Easy DIY repair—takes about 30 minutes with basic tools.

Spring that controls dispenser arm movement in refrigerators. Installs on the paddle assembly. Replace if broken, detached, or missing to restore arm function.

Protective cover that shields the LED light assembly in your refrigerator. Replace this housing if cracked, broken, or missing to restore proper coverage.

Connects water supply tubing sections in your refrigerator. Replace this plastic compression union if it's cracked, leaking, or broken. Installs inline.

Bottom freezer door shelf for side-by-side refrigerators. Provides storage on the freezer door. Replace if cracked, broken, or missing from impact damage.

Upper shelf for side-by-side refrigerator freezer doors. Replace when cracked, broken, or damaged from impact. Clear plastic assembly with mounting hooks.

This is a mounting screw used to secure various internal or external components in the refrigerator. It is a small Phillips pan-head fastener designed for use with the specific thread and length required by the appliance. Replace this screw if the original is stripped, lost, or damaged during a repair, causing a component to be loose or improperly secured.

Wiring harness for the recessed dispenser area of your refrigerator. Replace if wires are damaged, frayed, or connections are loose or corroded.

Replacement mounting screw for refrigerator panels, brackets, door handles, and trim. Needed when original hardware is missing, stripped, or corroded.

Refrigerator door hinge bushing provides smooth bearing surface for hinge pin. Replace if door sags, sticks, or misaligns. Confirm fit with your model.

This set screw secures refrigerator components—most commonly door handles—to their mounting studs. Replacing a missing or stripped screw restores a solid, secure feel and helps prevent loose or wobbly handles.

• Locks the handle to its mounting stud to keep it tight and secure
• Helps resolve a loose, wobbly, sliding, or rattling handle
• Replaces a missing, rounded, or damaged set screw
• Helps maintain proper handle alignment and consistent door operation

• Unplug the appliance or switch off power before servicing
• Ensure the handle is fully seated on the studs before tightening
• Start the screw by hand to avoid cross-threading; then tighten until snug
• Do not overtighten to prevent stripping the screw or handle threads