Parts for Ge PSF23NGTECC: 01 - Freezer Door Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Stainless steel fastener secures your refrigerator door handle to the door assembly. Replace worn, loose, or missing hardware for solid grip and alignment.

Replaces a broken or missing dispenser door stop on side-by-side refrigerators. Closes and seals the ice/water dispenser opening when not in use.

White plastic cam closure that aligns and secures the freezer door in the hinge area. Replace if cracked, broken, or worn to restore proper alignment.

Replacement ice dispenser guide for your refrigerator. Installs in the dispenser chute to direct ice cubes properly. Replace if cracked or broken.

This lower front trim piece attaches to the refrigerator base to cover and protect the grille area while keeping the appliance's front panel looking finished. It restores appearance and helps keep debris away from vents and components. What it does:

• Covers the lower front grille opening for a finished, OEM appearance
• Protects underlying vents and components from dust and accidental contact
• Helps direct airflow around the condenser/vent area for proper operation
• Replaces damaged, cracked, or missing trim to improve aesthetics

• One grille recess lower front trim

• Disconnect power to the refrigerator before attempting installation
• Typically secures with snap tabs and/or screws; align tabs and press or fasten as required
• Handle carefully to avoid scratching the finish and to prevent breakage of plastic tabs
• Obtain OEM replacements for secure installation

Ice won't dispense or dispenser flap sticks open? The ice dispenser solenoid controls ice flow. DIY-friendly repair with our install video.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

If your dispenser light stays off or won't turn on, this control board restores proper illumination. Moderate DIY, requires clip release and wiring.

Ice dispenser door assembly seals the ice chute opening on your refrigerator. Replace if cracked, warped, or the rubber gasket is damaged and leaking air.

Restores closing tension for refrigerator ice dispenser recess door. Replace if spring is weak, broken, or missing to keep door closing properly.

Connects the actuator to your refrigerator's ice chute door. Replace if cracked, broken, or worn to restore proper door operation and seal.

Bisque

Water or ice dispenser not working? This dispenser switch activates when you press the lever. Easy DIY repair—takes about 30 minutes with basic tools.

The Torsion Spring is an OEM part for GE refrigerators. It is essential for maintaining the proper tension and operation of the refrigerator door. This spring ensures the door closes smoothly and stays securely shut, preventing cold air from escaping and maintaining the appliance’s efficiency.

Causes of a bad torsion spring can include metal fatigue from regular use, corrosion from exposure to moisture, or damage due to excessive force or mishandling. Over time, these factors can weaken the spring, affecting the door’s performance.

Symptoms of a bad Torsion Spring include:

• Door not staying closed
• Difficulty in opening or closing the door
• Door feels loose or unbalanced
• Unusual noises when operating the door

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Connects water supply tubing sections in your refrigerator. Replace this plastic compression union if it's cracked, leaking, or broken. Installs inline.

Lever lock secures your refrigerator door handle assembly. Replaces broken or missing locks that allow handle to loosen or detach from door.

Replace your broken or cracked refrigerator freezer door module support bracket. Secures door bins and shelves in place. Direct fit replacement part.

Restores a stable storage surface inside your freezer. Replace this freezer shelf if cracked, warped, missing, or no longer seats securely in supports.

Wire tilt-out door basket for refrigerator doors. Replaces broken, cracked, or missing baskets. Installs in door to organize and store smaller items.

Handle lock bracket for refrigerator doors. Secures handle locking mechanism in place. Replace if bracket is cracked, broken, or missing for proper fit.

Bottom freezer door plug insert for side-by-side refrigerators. Replaces cracked, broken, or missing inserts to restore door appearance and seal.

Replacement mounting screw for refrigerator panels, brackets, door handles, and trim. Needed when original hardware is missing, stripped, or corroded.

Door hinge thimble for side-by-side refrigerators. Installs on the door hinge assembly. Replace if cracked, broken, or worn to restore proper alignment.