Parts for Dacor EF42NBSS: Freezer Liner Parts

If your fridge isn't cooling or freezer is making loud noises, the evaporator fan motor may have failed. Moderately easy DIY repair with video guide.

Loud noise or freezer warming up? This evaporator fan blade circulates cold air over coils. Simple DIY fix—most repairs done in under an hour.

Instruction sheet included.

Replace your refrigerator door gasket to restore proper sealing and energy efficiency. Prevents warm air leaks and frost buildup. Verify fit with model.

Instruction sheet included.

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

Air duct wedge for side-by-side refrigerators. Secures and positions air duct assembly in place. Replace if cracked, broken, or missing.

Screw: 8-16 x 3/8 inch.

Light bulb socket holds and powers the bulb inside your refrigerator. Replace if lights don't work despite new bulbs or if socket is cracked or damaged.

Illuminates appliance interior. Replace when burned out or dimming. Verify wattage and base type match your model before ordering. Easy DIY fix.

Fixes uneven cooling and warm refrigerator temperatures caused by poor airflow. This fan housing directs cold air from freezer to fridge. Easy 30-minute fix.

Left hand side

Foam air baffle block that installs between the evaporator fan housing and side wall. Replace if cracked, broken, or missing to restore airflow.

Air outlet cover for side-by-side refrigerators. Installs over internal air vent to direct cold air. Replace if cracked, broken, or missing.

Replacement screw for securing panels, brackets, and internal components. Replaces missing, stripped, or damaged fasteners to restore proper fit.

Replacement support stud that holds refrigerator shelves securely in place. Needed when original peg is broken, cracked, or missing from shelf wall.

Replacement #8-18 screw for securing panels, brackets, and components in appliances. Restores worn, stripped, or missing fasteners for safe mounting.

Right hand side

Left hand side

Seals the evaporator cover to the cabinet, preventing air leaks and frost buildup. Replace if you notice excessive frost or cooling issues. Verify fit.

Factory-style wire harness that routes power between refrigerator components. Replaces damaged, broken, or worn wiring and connector assemblies.

This insul-sound deadening pad reduces vibration and noise by dampening panels and components in laundry and kitchen appliances. It's a small adhesive-backed sound/isolation pad used where noise or rattles transfer through metal surfaces. What it does

• Dampens rattles and reduces structure-borne noise from panels, cabinets and housings.
• Helps isolate vibrating components from appliance chassis to lower perceived sound.
• Commonly applied behind control panels, cabinet walls or on motor mounts to cut vibration transmission.
• Useful when worn, detached or hardened factory pads allow increased noise.

• One insul-sound deadening pad

• Disconnect power before servicing an appliance to avoid shock or injury.
• Clean and dry mounting surface; press pad firmly to ensure adhesive contact.
• Replace only in the original location; do not cover vents or moving parts.
• If adhesive is weak, use OEM-approved adhesive; avoid solvents that may damage finishes.

Fix incorrect temperature readings or freezing in your fridge. This temperature sensor helps regulate cooling. Easy 15-minute DIY repair with one screw.

Fix inaccurate cooling or freezing issues with this refrigerator temperature sensor. Sends temperature data to the control board for proper regulation.

This replacement screw secures appliance panels and components to restore proper fit and stop loose or rattling parts. A simple, OEM-compatible fastener that helps maintain safe, stable operation and original assembly alignment. What it does:

• Secures panels, trim, brackets or components to prevent movement and vibration
• Restores proper fit when a screw is missing or stripped
• Helps eliminate rattling, gaps, or misaligned parts
• Fits the OEM threaded holes and fastening points

• Disconnect power (and gas if applicable) before accessing internal components
• Use the correct driver to avoid stripping the head; hand-start threads before final tightening
• Do not overtighten—stop when snug to avoid damaging threads or plastic parts
• Keep removed hardware organized to ensure correct reassembly

Fix frost buildup and warm fridge temps. This defrost thermostat monitors evaporator temperature to prevent overheating during defrost cycles.

Replacement screw that fastens panels, brackets, and internal components. Install when original is stripped, rusted, missing, or lost during repairs.