Parts for Kitchenaid KBFS20EVMS13: 02 - Freezer Liner Parts

Seals refrigerator or freezer door to prevent air leaks and maintain temperature. Replace if torn, deformed, or door won't close tightly. Confirm fit.

Repair kit for refrigerator drawer slide mechanisms. Includes gears and rod to replace stripped, broken, or missing components in pull-out drawer rails.

Replacement slide rail for refrigerator drawers and racks. Restores smooth gliding when original rail is cracked, broken, or worn. Direct-fit support.

Replacement drawer support rail for refrigerator bins. Restores smooth sliding and prevents sagging when the original rail is cracked, broken, or worn.

This is a gear shaft that serves as part of the drawer slide mechanism in the freezer section of your refrigerator. It helps the freezer drawer glide smoothly in and out on its track. Replace this shaft if the freezer drawer sticks, wobbles, or does not open and close properly.

Freezer or fridge light not working even with a new bulb? This light socket provides the electrical connection. Basic DIY repair with video guide.

Replacement airflow deflector for refrigerators. Redirects air and shields internal components. Needed when original is cracked, broken, or missing.

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

• Fastens covers, trims, brackets, and internal parts to the cabinet/frame
• Used wherever a #8-18 x 5/8 screw is specified
• Replace if the original is missing, corroded, stripped, or will not tighten
• Symptoms: loose or rattling panels, gaps, or hardware that backs out

• Disconnect power; shut off gas/water before servicing
• Match thread and length; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly—do not overtighten
• Inspect and replace damaged clips or tabs before securing

Shield guard for refrigerators. Protects internal components from damage. Replace if cracked, broken, or missing to maintain proper coverage.

Plastic evaporator cover for refrigerators. Installs over the evaporator coil in the freezer section. Replace if cracked, broken, or missing.

This replacement screw secures specified refrigerator components—such as covers, brackets, and internal panels—so they stay properly mounted. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and reliable operation.

• Provides the correct fastener for locations identified in your model's parts diagram
• Helps prevent looseness, vibration, and rattling of panels or brackets
• Replace if the head is stripped, threads are worn, or the screw is missing
• Symptoms can include loose parts, gaps, or noises from movement

• Unplug the refrigerator and shut off water if working near the ice maker or dispenser
• Match length and type to the original; follow your model's parts diagram for placement
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Keep track of screw positions; do not mix different screw lengths or styles

Mounting bracket for refrigerators. Secures internal components in place. Replace if cracked, bent, or broken to restore proper structural support.

Mounting bracket for bottom-mount refrigerators. Secures internal components in place. Replace if cracked, broken, or missing to restore proper support.

Secures and positions your freezer lamp assembly for proper lighting. Replace if cracked, broken, or loose to restore correct fit and illumination.

Secures panels, trim, and wire harnesses in your refrigerator to reduce vibration and rattling. Replace when clips break or parts become loose. Confirm fit with your model number before ordering.

Interior lights staying on or not working? This door switch controls refrigerator lighting and functions. Moderate DIY repair with video guide available.

Size: 8 x 1-1/4 inch.

Secures the freezer basket in the lower compartment. Replace this bracket cradle if cracked, broken, or missing to restore proper basket support and alignment.

Secures the freezer basket inside the freezer compartment. Replace if the cradle is cracked, broken, or missing to restore stable basket support.

Creates an airtight seal to keep cold air in and moisture out. Replace when worn or torn to restore cooling performance and prevent frost buildup.

Left-hand side adapter bracket secures and aligns your refrigerator's left panel. Replace if cracked, broken, or missing to restore proper fit.

Right-side adapter bracket mounts to the refrigerator cabinet and supports the shelf, bin, or panel. Replace when the original is cracked, loose, or missing.

This is a plastic vent grille that covers the air intake or exhaust area on the refrigerator, typically located at the bottom front or top of the unit. It allows airflow to the condenser while keeping debris out. Replace this grille if it is cracked, broken, discolored, or if missing louvers are restricting proper ventilation and causing the refrigerator to run warm.

Protective housing that covers refrigerator fan components. Replace if cracked or broken to ensure proper airflow and protection. Confirm fit with model.

Loud noise or freezer warming up? This evaporator fan blade circulates cold air over coils. Simple DIY fix—most repairs done in under an hour.

The refrigerator fan motor grommet is a small rubber cushion that mounts between the evaporator or condenser fan motor and its bracket, absorbing vibration during motor operation. It reduces noise and prevents the motor's vibration from transferring to the refrigerator cabinet. Replace this part if your refrigerator is making a rattling or buzzing noise coming from the fan area, which is often caused by a worn or deteriorated grommet.

Freezer cold but fridge warm? Your evaporator fan motor circulates air between compartments. Most DIYers complete this repair in 1 hour with our video.

Water pooling in freezer or fridge? A clogged or cracked defrost drain funnel causes leaks. DIY fix in 30-45 minutes by accessing the rear freezer panel.

Creates a watertight seal at water connections to prevent leaks. Replace when cracked, flattened, or worn. Confirm fit with your model number.

Seals the drain tube connection to prevent leaks and ice buildup in your freezer. Replace if you see water pooling or ice forming at the freezer bottom.

Freezer running too warm or too cold? This thermistor cover shields the temperature sensor for accurate cooling. Simple snap-in installation fixes misreads.

This sensor monitors temperature inside your refrigerator compartments and sends signals to the control board for proper cooling. It ensures your refrigerator maintains the correct temperature for food safety and energy efficiency. Replace this if your refrigerator runs constantly, doesn't cool properly, or shows inaccurate temperature readings.

Guides condensation from the defrost cycle to the evaporation pan. Replace if cracked, clogged, or causing water leaks and ice buildup in the freezer.

Replace your refrigerator's fill tube guide if cracked, broken, or missing. This plastic guide sleeve directs the water fill tube in your ice maker assembly.