Parts for Ge PGSS5RKZASS: 05 - Freezer Section Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Self-adhesive foam strip seals gaps around refrigerator doors to prevent air leaks and improve energy efficiency. Replace when compressed or damaged.

Rubber grommet that mounts and cushions the evaporator or condenser fan motor. Replace if cracked, worn, or missing to prevent vibration and noise.

Sheet metal screw secures refrigerator panels, trim, and brackets. Replace missing, stripped, or corroded screws to restore proper fit and assembly.

Mounting screw for refrigerator and freezer internal components. Replace if stripped, missing, or damaged during repairs. Secures panels and parts.

Evaporator fan cover protects the fan motor in your refrigerator's freezer compartment. Replace if cracked, broken, or missing to restore airflow.

Refrigerator evaporator foam pad cover insulates and protects the evaporator coil. Replace if torn, compressed, or missing to maintain efficiency.

Refrigerator foam pad holder that secures insulation padding in place. Replace this retainer if the original is cracked, broken, or missing. Direct fit.

This ground wire harness connects an appliance's metal chassis to its electrical ground to help maintain a safe, stable ground path and reduce risk of electrical faults. It's a direct-replacement harness used where the original ground lead is damaged or corroded. What it does

• Provides a dedicated grounding path between the appliance chassis and the household ground to help prevent electrical leakage and reduce shock risk.
• Restores proper chassis grounding when the original harness is broken, frayed, or shows corroded terminals.
• Can resolve intermittent electrical faults or nuisance tripping caused by a poor ground connection.
• Matches OEM connector types and routing points for a like-for-like replacement.

• One ground wire harness assembly

• Always disconnect power (unplug appliance or shut off circuit breaker) before inspecting or replacing grounding components.
• Verify correct routing and secure all terminal fasteners to the chassis; do not rely on paint or rusted surfaces for a good ground.
• Replace any corroded screws or mounting hardware; use manufacturer-specified fasteners where required.

Self-adhesive foam strip seals gaps around refrigerator doors to maintain temperature and prevent air leaks. Replace when worn or compressed. Confirm fit with your model number.

Protective insulation sleeve for refrigerator wiring harnesses. Installs around electrical wiring to prevent heat damage and wear. Replace if cracked or torn.

The Temperature Sensor Seal is an OEM part for GE refrigerators. This seal is designed to protect the temperature sensor from moisture and other environmental factors that could affect its accuracy and longevity. By providing a barrier against the harsh conditions within a refrigerator, such as humidity and temperature fluctuations, this seal ensures that the sensor can accurately monitor and control the refrigerator's internal temperature.

Causes of a malfunctioning Temperature Sensor Seal can include wear and tear over time, degrading the seal's effectiveness. Physical damage like tears or punctures can allow moisture to reach the sensor. Improper installation may leave gaps or loose areas around the sensor, compromising the seal.

Symptoms of a bad Temperature Sensor Seal include:

• Inaccurate temperature readings.
• Condensation or frost near the sensor location.
• Frequent cycling or unusual patterns in the refrigerator's cooling process.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.

Interior light not working when door opens? This light switch controls refrigerator illumination. DIY-friendly install takes 30-45 minutes with video.

Rattling noise or warm temps? A broken evaporator fan blade disrupts air circulation. This repair takes 30-45 minutes with basic tools and our video guide.

Wire tie retainer for refrigerators. Secures and organizes internal wiring. Replace if cracked, broken, or missing to keep wires properly bundled.

Secures the evaporator fan assembly to the freezer compartment wall. Replace this mounting bracket if cracked, broken, or missing hardware slots.

Secures the evaporator fan assembly behind the rear freezer panel. Replace if cracked, rusted, or missing to restore proper fan mounting and clearance.

Mounting screw for freezer interior components and panels. Replace if stripped, corroded, or missing to secure shelves, racks, or trim properly.

Fix a warm fridge with frozen evaporator coils. This defrost heater assembly melts frost buildup to restore proper cooling. Moderate DIY difficulty.

Fix frost buildup or uneven cooling in your refrigerator. This defrost thermostat regulates evaporator temperature to prevent ice accumulation.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Replace a cracked or missing refrigerator drain trough. This tube channels defrost water to the drain pan, preventing leaks inside your appliance.

This is a blower fan motor designed to circulate cold air within the refrigerator's ice maker compartment to promote efficient ice production. It draws chilled air from the freezer section and directs it over the ice maker assembly. Replace this motor if ice production has slowed significantly, the ice maker area is warmer than normal, or you no longer hear the fan running.

LED light board assembly that restores interior refrigerator illumination when lights fail or dim. Replace when experiencing uneven lighting or dark areas. Verify fit with your refrigerator model number before ordering.

Replacement LED light cover assembly for your refrigerator. Installs over the LED light unit to protect and diffuse light. Order when cracked or broken.

Fridge warm but freezer cold? Your evaporator fan motor likely failed. Fixes air circulation issues. Moderate DIY repair with basic tools.

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration over time due to frequent use, exposure to temperature variations, or damage from accidental impacts. A worn or damaged bumper may no longer provide adequate cushioning, leading to potential damage to the lid or the refrigerator itself.

Symptoms of a bad Lid Bumper include:

• The refrigerator lid closing too hard
• Unusual noises when closing the lid
• Visible wear or cracks on the bumper

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Rubber grommet that mounts and cushions the evaporator or condenser fan motor. Replace if cracked, worn, or missing to prevent vibration and noise.