Parts for Ge PSS23MSWASS: 04 - Freezer Section Parts

Removes contaminants from your refrigerator's water supply. Replace every 6 months or when water flow decreases. Verify fit with your model number.

Freezer air duct assembly for side-by-side refrigerators. Directs cold air from evaporator to compartments. Replace if cracked, broken, or missing.

Secures the lower freezer tower assembly to the refrigerator cabinet. Replace if cracked, broken, or missing to stabilize the tower and maintain alignment.

Mounting screw for refrigerator interior components like fan brackets, ice maker assemblies, and shelving. Replace if stripped, missing, or corroded.

Molded housing that protects the evaporator coil and directs airflow in your refrigerator. Replace if cracked, broken, or missing to maintain proper cooling.

Seals evaporator cover to freezer liner, preventing frost buildup and water leaks. Replace if worn or damaged to maintain cooling efficiency.

Upper freezer tower bracket secures the ice/tower assembly inside your refrigerator's freezer. Replace if cracked, broken, or missing to restore support.

Refrigerator freezer wire harness. Connects freezer components to main control. Replace if damaged, frayed, or connectors are broken or melted.

Freezer icing up or frost buildup? This defrost heater melts accumulated ice on evaporator coils. Moderately difficult repair requires panel removal.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.

Fix inconsistent temps or ice buildup on evaporator coils? This sensor seal protects accuracy. DIY-friendly with wire splicing. Video guide available.

Freezer coils icing up and fridge too warm? This defrost thermostat monitors evaporator temperature to prevent overheating. Easy 20-minute DIY fix.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Evaporator orifice housing assembly for side-by-side refrigerators. Covers and protects the evaporator orifice connection. Replace if cracked or broken.

Clear freezer light shield lens that protects the light assembly and diffuses illumination. Replace if cracked, yellowed, or missing. Confirm fit with your model number before ordering.

Black bottom door hinge and pin assembly for side-by-side refrigerators. Replace this load-bearing pivot component if cracked, broken, or worn out.

Secures mobility components and wheel brackets on side-by-side refrigerators. Replace if screw is missing, stripped, or worn to restore stable mounting.

Front caster assembly that mounts to the bottom of your refrigerator. Replace if cracked, broken, or worn to restore smooth rolling and stability.

This corner cap is a small trim piece that protects and finishes the corner of an oven door. It restores the door's appearance and helps keep the glass and trim edges covered for a clean, finished look. What it does:

• Covers and protects the outer corner of the oven door trim to prevent exposed edges
• Helps secure door trim and maintain a finished appearance
• Commonly replaced when cracked, broken, missing, or loose after impact or wear
• Fits where a small molded corner protector is required

• One corner cap as shown

• Disconnect power to the appliance before attempting any repair and allow the oven to cool completely
• Remove any screws or trim pieces that obstruct access; corner caps typically snap or slide into place
• Handle door glass and metal trim carefully to avoid chips or cuts

Refrigerator light not working or flickering? A faulty light socket often causes this. Simple plug-in repair with no tools required. Video guide available.

Illuminates your refrigerator interior. Replace when burned out or flickering. Appliance-rated for durability. Verify wattage and base type match.

Upper hinge pivot pin for side-by-side refrigerator freezer doors. Replace if bent, worn, or missing to restore proper door alignment and swing.

Replacement mounting screw for refrigerator panels, brackets, and hardware. Restores secure fit when original is missing, stripped, or corroded.

Fixes freezer or fridge light staying on, or ice dispenser not working when door closes. Simple 5-minute DIY fix with putty knife—video included.

Fix a warm freezer or thawing food with this evaporator fan motor. Circulates cold air over coils. DIY-friendly repair in about 30 minutes with basic tools.

Secures the evaporator fan assembly behind the rear freezer panel. Replace if cracked, rusted, or missing to restore proper fan mounting and clearance.

Secures the evaporator fan shroud to the rear compartment frame. Replace if rusted, cracked, or broken to properly support the fan assembly and alignment.

Rattling noise or warm temps? A broken evaporator fan blade disrupts air circulation. This repair takes 30-45 minutes with basic tools and our video guide.

Rubber bumper that cushions and mounts the evaporator fan motor assembly. Replace if cracked, deteriorated, or missing to reduce vibration and noise.

Rubber grommet that seals and cushions where the evaporator fan motor shaft mounts. Replace if cracked, worn, or missing to eliminate noise and vibration.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Protective cap that covers the evaporator fan motor bearing and housing in freezers and refrigerators. Replace if cracked, broken, or missing to prevent debris.

Black plastic lever assembly that installs on the freezer door hinge mechanism. Replace when cracked, broken, or missing to restore proper door closure.

Replacement door closure spring for refrigerator hinges. Installs on door hinge assembly to provide tension for proper closing. Needed when broken or worn.