Parts for Ge ZISB48DRB: 03 - Freezer Section Parts

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

Interior light not working when door opens? This light switch controls refrigerator illumination. DIY-friendly install takes 30-45 minutes with video.

Open - 45, close - 25

Fix ice buildup on freezer walls with a new defrost heater. Solves continuous icing and frost accumulation. Moderate DIY repair for most models.

This icing kit is a factory update designed to reduce frost build-up in the ice/dispenser area. It improves sealing and insulation to help keep the ice path clear and restore reliable dispensing performance.

• Reduces frost or ice accumulation cau

This pack contains twelve replacement screws used to fasten appliance panels, trim, and components. They restore secure mounting and help stop rattling, loose panels, and gaps for a safer, quieter appliance. What it does:

• Secures exterior and in

The Evaporator Fan Motor Kit is an OEM part compatible with GE refrigerators. It is a critical component responsible for circulating air and maintaining proper airflow within the refrigerator's evaporator system, ensuring efficient cooling and temperature regulation. It features a shaft that measures 3/8 of an inch and two right-side terminals. Notably, the motor no longer comes with harness wires, which must be obtained separately for installation.

Symptoms of a faulty evaporator fan motor include:

• Inconsistent or inadequate cooling in the refrigerator or freezer compartments
• Warm spots or temperature fluctuations within the refrigerator
• Excessive frost buildup or ice accumulation in the freezer

Causes of a bad evaporator fan motor can include wear and tear over time, electrical issues or short circuits, or physical damage from foreign objects or improper maintenance.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models. 

Freezer not cooling evenly or warm spots in fridge? A cracked evaporator fan blade stops airflow across coils. Simple DIY fix restores proper cooling.

The Fan Blade Grommet is an OEM replacement part for GE brand refrigerators. Located behind the evaporator fan blade where its central shaft passes through, this rubber sealing piece creates a protective barrier isolating the fan assembly.

Causes of a potentially problematic fan blade grommet include cracks or deterioration that develop from continuous vibration and impacts over extended use. Exposure to temperature fluctuations can also cause the rubber to harden and lose elasticity. 

Symptoms of a faulty fan blade grommet include:

• Airflow obstructions within the duct 
• Noisy vibrations from the fan assembly
• Rubber debris collecting on components

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore model refrigerators.

Secures refrigerator wiring to prevent chafing and vibration noise. Replace when damaged or missing to keep harnesses organized. Confirm fit by model.

Rear fan mounting bracket for freezers and refrigerators. Secures the fan assembly to the back panel. Replace if cracked, broken, or missing hardware.

Secures panels, brackets, and components inside your refrigerator or freezer. Replace when original fasteners are missing, stripped, or corroded.

Connects water supply tubing sections in your refrigerator. Replace this plastic compression union if it's cracked, leaking, or broken. Installs inline.

Replacement mounting screw that secures panels and internal components in your freezer. Replace stripped, rusted, or missing fasteners to restore stability.

Secures the defrost heater assembly in your refrigerator's freezer section. Replace if the original bracket is cracked, broken, or missing.

This icing kit is a factory update designed to reduce frost build-up in the ice/dispenser area. It improves sealing and insulation to help keep the ice path clear and restore reliable dispensing performance.

• Reduces frost or ice accumulation cau

Left side base roller assembly for refrigerators. Mounts to the bottom left corner to support and allow movement. Replace if cracked, worn, or broken.

Size: Small.

Mounts and secures the water valve inside your refrigerator. Replace if the original bracket is cracked, broken, or missing to properly support the valve.

Size: Large.

Mounting strap secures internal components inside your refrigerator. Replace if strap is cracked, broken, or missing to prevent movement and vibration.

This vent top gasket seals the front edge of the range vent to help contain heat, steam and cooking vapors and maintain a snug fit between the vent assembly and the cooktop. It replaces a torn, flattened or missing gasket to restore the vent seal. What it does:

• Seals the front vent seam to reduce heat and steam escape from the cooktop area
• Helps prevent grease, crumbs and debris from entering the vent cavity
• Reduces rattling or air gaps caused by a worn or compressed gasket
• Restores a proper fit between the vent top and surrounding surfaces

• Disconnect power (and gas if applicable) to the appliance before starting work
• Remove the vent top or cooktop per the appliance service instructions to access the gasket area
• Clean mating surfaces and remove old adhesive residue before installing the new gasket
• Use care with tools and sharp edges; wear gloves and eye protection

Freezer side shelf track.

Track screw for refrigerator drawer or shelf rail assembly. Replaces stripped, missing, or damaged screws that secure sliding tracks in place.

Mounting screw for refrigerator and freezer assembly. Replaces lost, stripped, or damaged screws used to secure internal components and panels.

Fix a leaking water valve or non-working ice maker and water dispenser. This dual inlet valve controls water flow to both systems. DIY-friendly repair.

Rubber grommet seals the ice maker fill tube where it enters the refrigerator cabinet. Replace if cracked, brittle, leaking, or missing to restore seal.

Delivers water from the supply line to the icemaker fill cup. Replace if cracked, frozen, or blocked to restore proper water flow to ice trays.

Plastic bushing that fits into the top hinge assembly on your refrigerator door. Replace if the original is cracked, worn, or missing to restore support.

Top hinge for refrigerator freezer compartment doors. Mounts at the upper corner to support door weight and allow smooth opening. Replace if bent, cracked, or stripped.

This is the left side slide. For right side use WR72X227.

This is the right side slide. For left side use WR72X226.

Actuator arm for freezer drawer assemblies. Replaces broken or missing arms that connect drawer slides to rails. Essential for smooth drawer operation.

Left side freezer basket roller for refrigerators. Slides freezer baskets in and out smoothly. Replace if cracked, broken, or causing baskets to stick.

Right side freezer basket roller for refrigerators. Replaces broken, cracked, or worn rollers that prevent smooth basket movement in the freezer.

To order top hinge use WR13X640.

Size: 8-18 x 1 ab.

Right side roller washer for refrigerators. Installs on the roller assembly to support smooth movement. Replace if cracked, worn, or missing.

This shear pin secures the washer agitator to the drive shaft and protects the transmission by designed failure when the agitator binds. It's a small, low-cost part that prevents costly gear or motor damage. What it does:

• Locks the agitator to t

Replace your worn or damaged freezer door hinge spring bushing. This small plastic component cushions the hinge spring mechanism and prevents metal-on-metal contact. Installs inside the hinge assembly.

This part has been discontinued by the manufacturer and is no longer available.

Plastic water line that connects the water inlet valve to the ice maker. Replace if cracked, leaking, or damaged. Includes installation video.

Hinge cover cap that installs over the hinge mechanism on your refrigerator door. Replace if cracked, broken, missing, or discolored for a complete look.

Compression nut and ferrule for refrigerator water line connections. Replace when cracked, worn, or missing to ensure secure fitting installation.

Connects water supply tubing sections in your refrigerator. Replace this plastic compression union if it's cracked, leaking, or broken. Installs inline.