Need Help?
Call or text
Burner won't heat or stopped working? This cooktop surface element restores heating. Easy 15-minute DIY repair—just swap connections one at a time.
Order the part to ApliancePartsPro and within 3 days I had it delivered to my front door. Looked up in their help page and was guided how to do it. It was so ease . I will recomend all my friend to get their parts at ApliancePartsPro. I am very please with the service and quality. Read more
Oven won't heat or bakes unevenly? A failed bake element is likely the cause. This lower heating element replacement typically takes 30 minutes or less.
Turned off the power to the oven, removed the old element and installed a new element that I purchased from Appliance Pros.com. The part was delivered in a timely manner and was packed securely for shipping. Thanks!!!!!! Read more
Oven won't heat or bakes unevenly? A faulty bake element is often the cause. This bottom heating element restores even baking. DIY install in 5-10 minutes.
Repair video was very helpful. Followed the instructions and the element was replaced easily and correctly. Read more
Oven not heating or baking unevenly? A failed bake element is often the cause. This replacement requires pulling the oven out to access the rear panel.
First, I took an ohm reading across the elements and determined the bad one, which was failed, open circuit. (Zero continuity) I then replaced the lower heating element of the upper oven. Although the design of the oven and element make it appear that it will just drop down and slide out the front, this is not quite the case. There is not enough clearance for it to drop all the way down. You have to pull the entire double-oven unit out of the wall, separate the upper and lower halves a few... Read more
Oven won't heat or bakes unevenly? The bake element likely failed. Simple DIY fix—just remove two screws, disconnect wires, and install new element.
I purchased a new elelmnt and fixed it myself!! Read more
Oven won't heat or bake properly? A failed bake element is often the cause. This bottom heating element replacement is straightforward—most DIYers complete it in under 30 minutes.
Watched the video here, took the leap that burner was the problem and ordered it. Also found another vid on you tube that was more specific to my Kenmore. Tip: find out how to take off the oven door. For mine it was very easy but not detailed in the APP vid. I followed instructions in APP vid but also first took off back panel of range and tested resistance of old burner to ensure that was truly the problem (as suggested by other YT vid). Also, dis/connecting the wires from the back is easier... Read more
Broil element not heating or burned out? This top heating element restores high-heat broiling for browning and crisping. DIY-friendly, 15-30 minute repair.
I replaced the element. I went on your site to order a new element, and had trouble locating the exact replacement. A young man named Kenneth came on live chat and assisted me. He found the correct one and assisted me with the order. It was all very smooth and quick. I received the part in two days ! Read more
Burner won't heat or heats unevenly? Replace the radiant surface element beneath your glass cooktop. Restores proper heat output for consistent cooking.
Replaced the oven heating element Read more
Oven not heating or heating unevenly? This bake element restores proper temperature for consistent cooking. DIY-friendly installation in under an hour.
I ordered an element one day it was there the next day, that was quick. It fit perfectly in place Read more
Oven won't broil or preheat properly? This broil element provides intense top-down heat. DIY-friendly repair restores even broiling in 30-45 minutes.
Replaced the element. 1st- Turn off the power to the appliance. The cook top is held on with two screws - access the screws by opening the oven door. Cooktop is hinged, so just pull up near oven door and hold in place with, say, a three foot long stick. The elements are held in place by bracket attached to the cooktop. Remove the bracket by removing the two socket screws. The element is aligned to the bracket with three locking tabs. Remove the tabs with pliers. I broke off one the... Read more
Oven won't heat or bakes unevenly? A failed bake element is often the cause. This 2300W replacement part installs in 5-10 minutes with basic tools.
Turns out these wall ovens have a pretty common problem, the baking element relay on the back of the control board solder joint fails. We have had this happen on several units recently as we manage several apt complexes. So it was not the baking element at all, just faulty solder joints or something makes the baking element relay lose its solder connection. Read more
Burner won't heat evenly or only outer ring works? This dual 9/12 inch radiant surface element restores proper heating. Easy DIY replacement in minutes.
Replace element. Read more
Oven not heating or preheating slowly? A failed bake element is usually the cause. This direct-heat component restores even baking. DIY repair in 30 minutes.
Unplugged the stove, unscrewed the mounting plates from the back unsnapped the wires then revered the procedure to install new one. Read more
If your oven won't heat above 250°F or the broiler stopped working, the broil element likely failed. This DIY fix restores full heat in 30-45 minutes.
Turned off power to oven. Removed the oven door. Unscrewed and removed the metal plate. Pulled element off wires and attached them to the new element. (This took needle nose pliers and many attempts. Needed dexterous fingers and good eyesight.) Put everything back. Read more
Oven not heating to temperature or losing heat during baking? This bake element restores consistent heating. DIY repair typically takes 20-30 minutes.
Pulled out the old one, popped in the new one 20 minutes. Fixed. Read more
Broiler not heating or working? This broil element restores high-heat cooking. Easy DIY fix with four screws and wire connectors. Takes about 30 minutes.
Removed the element "easy just four screws" unplugged two connecting wires, removed element. Did a "continuity test" on element, it failed, so I ordered a new one and installed it. It works great now. Read more