Frigidaire Dryer Parts

Replace your dryer's timer dial if it's cracked, broken, or won't turn properly. This control dial mounts on the timer shaft to set drying cycles.

Replacement door panel for dryers and laundry centers. Restores exterior appearance when the original panel is cracked, dented, or damaged.

Rubber bumper that cushions the range door or drawer when closing. Replace if cracked, worn, or missing to prevent rattling and protect surfaces.

This clip secures the lint screen frame to the dryer housing, keeping the lint filter properly seated during operation. It snaps into place to hold the frame firmly so the lint screen does not shift or rattle. Replace this clip if it is broken or missing, which can cause the lint frame to sit loosely or allow the lint screen to move out of position.

Gas conversion orifice for dryers. Converts natural gas units to LP/propane fuel type. Replace if orifice is lost, damaged, or switching fuel sources.

This replacement nozzle assembly directs and controls water flow in the appliance, restoring proper delivery to the dispenser or ice-making components. It replaces a worn or damaged nozzle to help stop leaks and restore consistent flow. What it does

• Directs water from the supply line to the dispenser or ice-making fill tube.
• Helps stop spraying or leaking when the original nozzle is cracked or blocked.
• Restores steady water flow when the dispenser produces weak or intermittent water.
• Fits into the original mounting and seals the water path when properly installed.

• One nozzle assembly as shown.

• Turn off water supply and unplug the appliance before starting work.
• Inspect surrounding seals and tubing; replace any damaged parts to ensure a proper seal.
• Hand-tighten fittings and check for leaks after restoring power and water.

This user interface control board replaces the oven's front control module so you can send commands and view settings. It restores responsive touch/buttons and proper display feedback for normal operation. What it does

• Receives button/touch inputs and relays commands to the oven control system
• Provides display/status feedback so settings and timers are visible
• Helps resolve unresponsive buttons, blank or incorrect display readouts, or intermittent control behavior
• Works as the main input surface for oven functions like bake, broil, timers, and temperature settings

• One user interface control board (UI board) — only items explicitly listed by the manufacturer are included

• Turn power to the appliance off at the breaker before servicing to avoid electrical shock
• Handle the board and connectors carefully; avoid touching contacts or flexing the board
• Verify connector orientation and secure mounting; test operation with power restored

Dryer takes too long or won't dry clothes? A damaged blower wheel reduces airflow. This plastic fan restores proper drying and reduces noise.

Electrical wire harness for dryers. Replaces damaged, frayed, or worn internal wiring connections. Essential when harness is broken or corroded.

Wire harness connects electrical components in your dryer. Replace if wires are frayed, corroded, melted, or damaged to restore safe power routing.

Replacement mounting screw for dryers. Secures panels, brackets, and internal components. Order if your original screw is stripped, missing, or damaged.

Harness cable tie secures and organizes wiring inside your appliance. Replace if damaged, cracked, or no longer holding wires firmly in place.

This is a replacement mounting screw used to secure the defrost timer assembly to the refrigerator control housing, restoring proper fastening and preventing the timer from shifting or vibrating during operation. What it does:

• Secures the defrost timer to the control housing so the timer stays in position.
• Prevents vibration or movement that can cause intermittent contact or noisy operation.
• Helps maintain reliable defrost cycle timing by keeping the timer properly aligned.
• Addresses symptoms such as a loose or missing fastener, rattling behind the control panel, or a timer that shifts when the door is opened.

• Unplug the appliance before starting work to prevent electrical shock.
• Access the control housing or timer bracket per your model's service instructions.
• Use the correct screwdriver or driver bit; do not overtighten—stop when snug to avoid stripping.
• Retain removed hardware for reference and compare screw length/threads before installing.