Frigidaire Dryer Screws, Nuts, Washers

A replacement hex washer head screw that secures appliance panels and components. Durable hardware designed to match OEM fit so you can restore proper fastening and reduce rattling or loose parts. What it does:

• Fastens panels, brackets, and assemblies where a 1/4-20 thread is specified
• Provides a built-in washer head to distribute load and resist pull-through
• Commonly used where vibration or movement can loosen standard screws
• Helps stop rattling, misalignment, or loose trim caused by missing or stripped fasteners

• Use the correct screwdriver or socket to avoid stripping the head; tighten until snug, do not over-torque
• Replace any damaged mating hardware or worn threads for a secure fit

This replacement screw fastens panels, brackets, and internal components so assemblies stay aligned and tight during operation. With an 8-18 thread and 0.711-inch length, it matches the original hardware for a precise, reliable hold.

• Secures panels, brackets, and internal components to the cabinet/frame
• Replaces missing, stripped, or corroded screws
• Helps reduce vibration, rattling, and gaps from loose hardware
• Restores proper alignment after service or transport

• Disconnect power and shut off water/gas before servicing.
• Support panels/components while removing and installing the screw.
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten.

A replacement hex-head screw used to secure appliance regulator brackets and similar small components. Restores proper fastener fit so panels and brackets stay firmly attached. What it does

• Fastens regulator bracket and related sheet-metal components
• Provides a secure threaded connection for components where an 8-18 thread is specified
• Helps eliminate looseness or rattling caused by a missing or damaged screw
• Matches the nickel/chrome finish commonly used on interior mounting locations

• One hex head screw (8-18 x 3/8), nickel finish

• Intended for use where an 8-18 x 3/8 hex screw is specified by the manufacturer
• Tighten to snug; avoid over-torquing which can strip sheet-metal threads
• Turn off power to the appliance before accessing internal components
• If the original screw used a lock washer or threadlocker, replace or reapply as appropriate

Specs: 8 - 18 x 0.500

Replacement mounting screw for various appliances. Needed when original screws are stripped, lost, or damaged during repair or maintenance work.

Hex washer head ,10-32 x 0.375. Ground

Replacement screw for securing dryer trim, panels, and interior components. Needed when original fastener is lost, stripped, or damaged during repair.

Replacement mounting screw for washers and laundry centers. Secures panels, components, or brackets. Replace if lost, stripped, or corroded.

Hex flange nut with 10-32 thread secures components in appliances. Replace if stripped, missing, or damaged. Flange provides broader bearing surface.

This clip secures the lint screen frame to the dryer housing, keeping the lint filter properly seated during operation. It snaps into place to hold the frame firmly so the lint screen does not shift or rattle. Replace this clip if it is broken or missing, which can cause the lint frame to sit loosely or allow the lint screen to move out of position.

This replacement nozzle assembly directs and controls water flow in the appliance, restoring proper delivery to the dispenser or ice-making components. It replaces a worn or damaged nozzle to help stop leaks and restore consistent flow. What it does

• Directs water from the supply line to the dispenser or ice-making fill tube.
• Helps stop spraying or leaking when the original nozzle is cracked or blocked.
• Restores steady water flow when the dispenser produces weak or intermittent water.
• Fits into the original mounting and seals the water path when properly installed.

• One nozzle assembly as shown.

• Turn off water supply and unplug the appliance before starting work.
• Inspect surrounding seals and tubing; replace any damaged parts to ensure a proper seal.
• Hand-tighten fittings and check for leaks after restoring power and water.

Replacement mounting screw for dryers. Secures panels, brackets, and internal components. Order if your original screw is stripped, missing, or damaged.

This is a replacement mounting screw used to secure the defrost timer assembly to the refrigerator control housing, restoring proper fastening and preventing the timer from shifting or vibrating during operation. What it does:

• Secures the defrost timer to the control housing so the timer stays in position.
• Prevents vibration or movement that can cause intermittent contact or noisy operation.
• Helps maintain reliable defrost cycle timing by keeping the timer properly aligned.
• Addresses symptoms such as a loose or missing fastener, rattling behind the control panel, or a timer that shifts when the door is opened.

• Unplug the appliance before starting work to prevent electrical shock.
• Access the control housing or timer bracket per your model's service instructions.
• Use the correct screwdriver or driver bit; do not overtighten—stop when snug to avoid stripping.
• Retain removed hardware for reference and compare screw length/threads before installing.