Frigidaire Range / Cooktop / Oven Parts

Secures the glass light cover to your range oven cavity. Replace if the retainer is cracked, broken, or missing to keep the lens firmly in place.

Support bracket that secures the broil heating element in your range oven. Replace if cracked, broken, or missing to properly mount the broiler element.

This rocker switch is the on/off control used in the appliance's control panel. It opens and closes the circuit to a selected feature, restoring dependable operation when the original switch becomes worn, stuck, or fails.

• Controls a single on/off circuit from the control panel
• Restores proper switching for the associated feature
• Common symptoms: feature won't turn on or off, light or function flickers or stays on, switch feels loose or sticks
• Replaces a cracked, burned, or unresponsive rocker

• Disconnect power at the breaker before servicing
• Access the switch from the control panel or mounting area; note/photograph wire positions
• Move wires to the new switch one at a time and seat the switch securely in the panel opening
• Restore power and test operation before reassembly

Tension spring provides counterbalance for smooth oven door operation. Replace if worn, broken, or missing to restore controlled opening and closing.

Display blank or controls unresponsive? This oven control board manages the clock, timer, and cooking functions. Moderate difficulty repair restores operation.

Oven won't heat or bakes unevenly? Replace the lower bake element to restore consistent heating. This DIY fix takes about 30 minutes with basic tools.

Replaces cracked, rusted, or missing trim around your range door. Covers raw edges and fasteners to restore a finished look and secure the outer panel.

This potentiometer kit is the user-adjustment control the appliance reads to set operating levels. Replacing a worn potentiometer restores smooth, predictable response when you turn the knob, helping the control register settings accurately.

• Varies electrical resistance so the control can interpret knob position
• Helps set functions such as speed, power level, or temperature as designed
• Failure can present as no change when turning the knob, jumpy/erratic response, or settings stuck at one level
• Can also cause intermittent operation or "dead spots" while adjusting

• Disconnect power to the appliance before servicing
• Access the control area; note wire positions or take a photo before removal
• Transfer any knob/shaft adapter from the old part if applicable; secure the new pot without over-tightening
• Route wiring away from sharp edges and heat sources; verify proper operation before reassembly

This wiring harness connects the appliance's electrical components to restore reliable power and signal routing. It replaces a damaged or worn harness to help resolve power loss and intermittent electrical issues. What it does:

• Transfers power and control signals between components so controls and motors can operate
• Replaces frayed, burned, or broken wiring that can cause intermittent operation
• Helps stop failures that lead to no-start or loss of specific functions
• Restores secure connector fit to reduce arcing or poor connections

• Always disconnect power before servicing the appliance
• Match connectors and wire routing to the original harness; avoid stretching or pinching wires
• Secure fasteners and strain reliefs; verify all connections are fully seated
• If you find heat or burn damage at terminals, inspect adjacent components for root cause

Replace a broken, cracked, or missing control knob on your electric cooktop. Installs on the control panel to adjust burner settings and temperature.

This is a black burner cap that sits on top of a medium-sized gas range surface burner. It distributes the flame evenly around the burner for consistent heating. Replace this cap if it is chipped, cracked, warped, or if the burner flame is uneven or yellow instead of blue.

The Surface Burner Base is an OEM part for Frigidaire gas ranges. It provides a stable foundation and housing for the range's burners. Each burner base has a molded indentation to securely hold the burner assembly in place while cooking. 

Causes of a bad Surface Burner Base can include warping or distortion from overheating, cracks or punctures from impact or mishandling, or damage from corrosion over time.

Symptoms of a bad Surface Burner Base include: 

• Burners wobbling or moving out of position during use
• Gas or liquid leaks around burner housing 
• Irregular or uneven cooking performance 
• Loose, damaged, or missing burner assemblies

This genuine OEM Frigidaire base is also compatible with some Electrolux, Gibson, Kelvinator, and Kenmore models.

Uneven baking or convection mode not working? This rear-mounted convection fan heating element circulates hot air for consistent cooking results.

White control knob for electric ranges. Replaces cracked, broken, or missing knobs on your cooktop. Sold individually - order quantity needed.

Black control knob for electric ranges. Restores your cooktop's interface when the original is cracked, broken, worn, or missing. Direct-fit replacement.

Burner won't light or flame height won't adjust? This top burner valve controls gas flow to restore reliable ignition and precise flame control.