Frigidaire Wall Oven Parts

This extra-large burner crown replaces the outer decorative cap on a cooktop surface burner, restoring proper flame distribution and cookware support for large pots and pans. Durable finish helps maintain even heating and appearance. What it does:

• Covers and protects the burner head while directing flames for even heating
• Supports large cookware on the cooktop surface
• Can reduce uneven or weak flames caused by a damaged or warped crown
• Restores proper fit and appearance for an extra-large surface burner

• One extra-large burner crown

• Ensure the cooktop is completely cool and gas or power is turned off before starting
• Remove and replace gently to avoid bending the burner head; no special tools usually required
• Follow the appliance manufacturer's instructions and safety guidelines

Surface burner cap sits atop the burner head to shape and center the flame. Replace if cracked, chipped, or missing to restore proper flame distribution.

Oven door gasket creates a tight seal to maintain temperature. Replace if torn, flattened, or crispy. Clips into door frame. Confirm fit by model number.

Fix a blank display, beeping error codes, or non-working oven timer with this range clock control board. Most DIYers complete this repair in 15 minutes.

Control knob for gas range burners. Installs on control panel to turn burners on and adjust heat. Replace if cracked, broken, loose, or missing.

This control-panel switch restores reliable on/off control of a selected function on your range or wall oven. Replacing a worn or intermittent switch helps ensure the appliance responds consistently when you toggle that function.

• Directs power to the associated circuit when switched on or off
• Common symptoms: function won't turn on/off, intermittent operation, or the switch feels loose/sticks
• Helps restore positive, consistent control from the backguard/control panel

• Disconnect power at the breaker before servicing
• Access the switch from the control panel/backguard; retain screws/clips
• Label/photograph wire positions and transfer leads one at a time to the new switch
• Ensure firm terminal connections, reassemble, restore power, and test operation

This factory wire harness routes electrical power and signals between the controls and internal components of your cooking appliance. Replacing a burned or brittle harness restores safe, reliable connections and helps prevent shorts or intermittent operation.

• Distributes power and control signals between the user interface/control system and internal components
• Replaces damaged wires or connectors that can cause no operation or intermittent function
• Helps address short-to-ground conditions that trip a household breaker
• Restores proper routing to reduce wire chafing and heat exposure

• Disconnect power at the breaker or unplug the appliance before servicing
• Photograph/label connections and transfer one connector at a time to match original locations
• Route along factory paths and secure with existing clips/ties; keep clear of sharp edges and hot surfaces
• Inspect mating terminals for heat damage and repair/replace affected parts before reassembly

Fixes oven that won't heat properly, takes too long to reach temperature, or shuts off unexpectedly. Controls heating elements. Moderate difficulty repair.

This water inlet valve controls water flow to the refrigerator's dispenser and ice system so you get a steady supply when needed and stop unwanted leaks. It replaces a worn or failing valve to restore proper water delivery. What it does:

• Opens and closes to allow water into the ice maker and dispenser
• Stops water flow when dispenser/ice fill is inactive
• Commonly replaced when water won't dispense or ice maker won't fill
• Needed if the valve is leaking or causing water drips

• Disconnect power and shut off the water supply before replacing the valve
• Handle with care and inspect inlet/outlet fittings and gaskets for proper sealing
• Reconnect water and power, then check for leaks and proper water flow after installation
• Follow manufacturer instructions

Surface burner crown that mounts on sealed gas burners to distribute gas through flame ports. Replace if worn, clogged, cracked, or missing.

Cosmetic overlay that covers and protects your range's control panel surface. Replace if scratched, cracked, peeling, or worn from kitchen use and spills.

Fix oven that won't heat, inaccurate temperatures, or unresponsive display with this electronic control board. Restores bake/broil functions. 15-minute DIY.

White control knob for gas range. Replaces broken, cracked, or missing knobs on the control panel. Direct replacement for worn stovetop controls.

Replacement spring for microwave door latch mechanism. Restores return tension so the latch engages and releases correctly. Needed when spring is broken or worn.

Replacement control knob for your range. Restores smooth dial operation when original knob is cracked, broken, peeling, or worn. Sold individually.

Replace your gas range control knob if the finish is worn, markings are illegible, or the knob is cracked or missing. Installs on the control panel.