Frigidaire Wall Oven Parts

This replacement power cord restores electrical connection to the appliance so it can receive mains power safely. Use it when the original cord is frayed, damaged, or no longer providing a reliable connection. What it does:

• Replaces a damaged or worn appliance power cord to restore reliable power
• Resolves intermittent power, sparking at the plug, or visible cord damage
• Provides the necessary insulated conductors for safe appliance operation
• Works as a direct cord-replacement when the original cord is defective

• Always disconnect power at the breaker or unplug the appliance before installing
• Route the cord and secure strain relief per the appliance's original routing to prevent pinching
• Ensure the cord's connector and grounding match the appliance's inlet before connecting

This surface burner knob mounts to the cooktop control shaft so you can turn the burner on and choose the heat level. Replace a broken or stripped knob to restore safe, accurate control and a clean, finished look.

• Attaches to the burner valve or surface element switch shaft
• Provides on/off and heat-level selection
• Replaces knobs that are cracked, missing, loose, or stripped
• Helps keep settings aligned for consistent results

• Allow the cooktop to cool; switch off power at the breaker or shut off gas
• Pull the old knob straight off the control shaft—do not pry on the panel
• Align the new knob with the shaft shape and push straight on until fully seated
• If the shaft is worn or damaged, the valve or switch may require service

This replacement part is a genuine OEM frigidaire oven control board. The oven control board is the main circuit board that controls the ovens' essential functions. If the oven isn't heating properly, not turning on, or showing an error code on the digital display, it might be time to replace the control board. Replacing a control board may seem like a difficult task, but it is actually a relatively simple process. First, unplug the power to the stove. Move the appliance back to gain access to the back. Remove the upper back panel, and locate the control board. Take note of the order of the wires using a phone camera. Then detach the wire harness from the old control board. Remove any individual wires with needle-nose pliers. Then re-attach the wires to the new control board in the correct terminals. Snap the new control board into place and reinstall the upper back panel of the range.This replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand ovens.

This is the factory glass assembly that restores a clear, intact viewing window on your appliance door. Replacing a damaged panel helps maintain safe operation and a clean, finished appearance.

• Replaces a cracked, shattered, or missing glass panel on the door
• Helps maintain proper door integrity and safe use
• Restores visibility into the cavity for monitoring cooking or baking
• Addresses rattling, loose, or sharp-edge conditions caused by broken glass

• Disconnect power and allow the unit to cool completely before servicing
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Support the door during removal; keep track of screws and trim orientation
• Reassemble in the original order; do not overtighten fasteners

This electronic control board regulates oven functions and the display, interpreting keypad inputs and controlling the bake and broil elements. Replacing a failed board restores responsive controls, accurate heating, and a readable clock/timer.

• Controls bake and broil element power using temperature sensor feedback
• Manages oven modes, timers, and the display/clock
• Interfaces with the keypad membrane to read user selections
• Failure symptoms can include no heat, oven won't start, erratic temperatures, or a dead/flickering display

• Disconnect power at the breaker before servicing to avoid electrical shock
• Handle the board by the edges; use ESD protection to prevent static damage
• Photograph wiring and transfer connectors one at a time to the new board
• Reuse existing mounting hardware and front overlay if applicable; correct orientation before securing

This replacement control knob lets you turn the range's control shaft to set burner or oven temperature. Swapping a cracked or loose knob restores a secure grip and accurate, easy selection of settings.

• Attaches to the control stem to adjust heat levels or oven temperature
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps when the knob falls off or spins without engaging the control
• Restores proper feel and alignment of settings on the control panel

• Ensure the appliance is off and cool before servicing
• Pull the old knob straight off the stem; do not twist or pry with tools
• Align the new knob with the stem orientation and press firmly until fully seated
• If the knob won't seat, inspect the control stem for wear or damage before forcing

This clock timer is the electronic control that runs your range or wall oven's display, timer, and cooking functions. Replacing a failed control restores the clock/timer and reliable bake/broil operation when the display or controls stop working.

• Manages the clock, timer, and user interface; processes keypad/touchpad inputs
• Controls bake and broil elements via internal relays to reach and maintain set temperatures
• Coordinates preheat and temperature regulation using sensor feedback
• Common symptoms of failure: blank or erratic display, unresponsive buttons, oven won't start or heat, or unexpected error codes

• Disconnect power at the breaker before servicing; verify no voltage at the appliance
• Photograph/label wire connections and move harnesses one at a time to the new control
• Transfer any model-specific mounting hardware or faceplate as needed
• Handle the board by the edges and protect from static discharge

This is an outer glass door used in ovens. It is the outermost part of the door on the appliance. It helps hold together the other parts of the oven so it can operate correctly. This part is made of durable materials but can crack or otherwise become damaged.Before replacing the oven outer door glass, wait for the oven to cool completely. Make sure it is unplugged and/or the gas is turned off before beginning. A set of tools and work gloves will be useful for the process. The oven frame will need to be removed to replace the part. Remove the old outer door glass and replace it with the new part before reinstalling other components.This is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as a single part. The outer door glass is made to be used with ranges, stoves, ovens, and oven/microwave combination appliances by Kenmore, Frigidaire, and Crosley.

This radiant surface element restores heat to a glass-ceramic cooktop burner. Replace a failed element to bring back even, reliable heating and responsive temperature control for everyday boiling, simmering, and cooking. What it does:

• Provides radiant heat to a designated cooking zone beneath the glass cooktop
• Common symptoms: surface burner won't heat, heats unevenly, or cuts out intermittently
• Visible signs can include burned or cracked element traces or damaged terminals

• 1 radiant surface element

• Disconnect power at the breaker before servicing; allow the cooktop to cool completely
• Lift or remove the glass top to access the element
• Photograph wiring and transfer leads one at a time to the new element to maintain correct connections
• Support the element and brackets during reassembly and avoid touching the element surface with bare hands

This clock timer is the control that displays the time and runs timed-cooking features. On models that use it as the main oven control, it also coordinates bake and broil. Replacing a failed unit restores reliable operation. What it does:

• Displays time-of-day and manages kitchen timer, delayed start, and cook duration functions
• On applicable models, controls oven heating by signaling bake/broil circuits to start and stop
• Common symptoms of failure: blank or dim display, inability to set clock/timer, oven won't start or shuts off unexpectedly

• 1 clock/timer control assembly

• Disconnect power at the breaker before servicing
• Access the control behind the console/control panel; label or photograph all wire connections
• Handle the board carefully to avoid static discharge and damage to terminals
• Transfer existing mounting brackets and any faceplate/overlay if your model uses them; secure and test operation before final reassembly

This is the electronic clock and oven control that manages bake and broil functions while displaying time, temperature, and status. Replacing a failed timer restores accurate temperature control and reliable oven operation.

• Regulates oven heating by sending power to bake and broil circuits
• Displays time, set temperature, and cycle status
• Buttons allow setting bake, broil, and timer functions
• Common failure symptoms: no oven heat, inaccurate temperature, unresponsive buttons, error codes, or a blank/partial display

• Disconnect power at the breaker before servicing
• Handle the control carefully; avoid static discharge to the board
• Note wire locations or take photos before removal
• After installation, verify operation and run a test bake

This replacement screw secures appliance components and panels. Restore a snug, factory fit when original hardware is missing or stripped, helping prevent rattles, vibration, and misalignment so your unit operates safely and quietly.

• Fastens panels, brackets, or internal parts to the cabinet or frame
• Replaces missing, rusted, or stripped screws
• Helps correct loose or misaligned components
• Reduces rattling or vibration noises caused by loose hardware

• Disconnect power to the appliance before servicing
• Replace one screw at a time to maintain alignment
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Do not overtighten; repair damaged threads or replace related clip/insert if needed

The Burner Cap is an OEM replacement part that fits Frigidaire ranges. It is responsible for covering the medium burner igniter on the cooktop. Over time, the cap can become damaged from heat exposure and food debris. Causes of failure include cracking, warping, and corrosion. 

Symptoms of a failing medium burner cap include:

• Uneven or abnormal flame
• Ignition issues
• Improper fit and instability

This cap is compatible with Frigidaire, Gibson, White Westinghouse, Kelvinator, and Kenmore ranges

A replacement broil element for the oven that delivers direct top heat for browning and broiling. Restores broil performance and even top-side cooking when the original element is cracked, burned, or no longer heats properly. What it does:

• Produces intense top heat used by the oven's broil cycle for browning, crisping, and finishing dishes.
• Replaces a visibly damaged, cracked, or burned element that causes poor browning or weak broil performance.
• Helps restore consistent broiling and even top-side cooking when the original element fails or glows unevenly.

• Disconnect power at the breaker before starting any service to avoid electrical shock.
• Element mounts at the top of the oven cavity and attaches to the oven's wiring via insulated terminal connectors; handle terminals carefully.
• Inspect terminal connections and surrounding insulation during replacement; replace damaged wiring or hardware as needed.

This electronic oven control board governs the appliance's heating and front-panel functions. Replacing a failed board can restore accurate temperature control, mode selection, and display/timer operation.

• Controls bake and broil relays to reach and maintain the set temperature
• Manages the oven clock, timer, and digital display
• Receives keypad inputs for mode and temperature selection
• Monitors the temperature sensor and can register fault codes
• Common symptoms: oven won't heat or start, blank/erratic display, unresponsive buttons, random beeps or error codes

• Disconnect power at the breaker before servicing
• Use ESD precautions; avoid touching circuitry and contacts
• Label or photograph all wiring; transfer mounting hardware and the existing faceplate/overlay if applicable
• After installation, run a test cycle; some models may require initialization or calibration per the service sheet in the unit

Color: Black

The Knob is an OEM part for Frigidaire ranges. The knob attaches directly to the surface element switch and allows for easy adjustment of settings with a simple turn.

Causes of a bad range knob can be normal wear and tear over time, exposing the knob to excessive heat, or accidental damage from impact.

Symptoms of a bad range knob include:

• Loose, wobbly or difficult to turn fitment
• Cracked, broken or missing pieces
• Control functions that do not work as intended
• Inaccurate temperature readings
• Knob that falls off or does not stay securely attached

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.