Frigidaire Wall Oven Parts

This electronic clock timer assembly controls the oven clock and timed cooking functions so you can set cook times, delays and use the timer/countdown features. It replaces a faulty control module to restore timer and display operation. What it does:

• Shows and keeps the oven clock time; allows setting delayed start and timed cook cycles
• Operates the oven's timer/countdown features and audible alerts
• Responds to front-panel touch pads/buttons for programming and control
• Common symptom: blank or unresponsive display, clock not keeping time, or timer functions not working

• One electronic clock timer/control assembly

• Disconnect power to the appliance before starting any work to avoid shock
• Handle the display and control board carefully; avoid touching circuit traces and use anti-static precautions if available
• Installation typically requires removing the control panel or console

This oven bake element is the lower heating element that provides consistent radiant heat for baking and roasting. It restores the oven's ability to reach and hold baking temperatures for even cooking results. What it does:

• Heats the oven cavity from the bottom for baking and roasting
• Replaces a broken or visibly damaged element that won't heat or glow
• Helps correct uneven baking or failure to reach set temperatures
• Works with the oven's thermostat and controls to maintain cooking heat

• One lower/bake oven element

• Disconnect power to the range or oven at the breaker before servicing
• Access may require removing the oven floor or rear access panel; handle terminals carefully
• Inspect terminal connections and mounting hardware; tighten or replace as needed

This rubber bumper cushions doors and panels to reduce noise, prevent metal-on-metal contact, and protect finishes for smoother, quieter operation. Replace worn or missing bumpers to help restore proper seating and reduce rattling. What it does:

• Absorbs shock between moving parts to prevent bangs and scratches
• Keeps doors and panels aligned for a tighter seal and quieter close
• Reduces vibration and rattling during operation
• Helps protect painted or plated surfaces from wear at contact points

• Disconnect power to the appliance before servicing to avoid electrical hazard
• Typically a push-in or snap-in replacement; press into the original mounting hole until seated
• Inspect nearby bumpers and replace in matched sets if others are cracked or missing

This is a medium burner pan that is used with ranges and stoves. The burner pan is located under the heating unit to catch any drips and spills. This prevents the drips from reaching the internal components of the stove where they could cause additional damage. Over time, the burner pan can be overly soiled and damaged and may need to be replaced. The process of replacing the medium burner pan takes only a few minutes. The first step is to unplug the stove or range. Next, the elements on the cooktop need to be lifted to access the parts underneath. The burner pan will be found in one of the cavities under the burners. These can be removed by hand and set aside. When replacing the burner pan, make sure the hole on the side is oriented to fit the terminals. Plug the elements back in and plug in the stove.The medium burner pan is made for use with ovens, ranges, and stoves manufactured by Kenmore and Frigidaire. It is sold as an individual product. This is an authentic OEM replacement part that is sourced directly from the manufacturer.

Color: Black

This is a #8 screw, 0.500 inch long, used to secure panels and components in appliances. It provides a correct-fit fastener for repairs where the original #8 x 1/2" screw was required, restoring proper assembly and stability. What it does:

• Fastens trim, panels, brackets and small components where a #8 x 1/2" screw is specified
• Holds parts securely to prevent rattling, gaps or loose panels
• Replaces worn, stripped or missing screws to restore proper fit
• Appropriate for common interior and exterior appliance mounting points

• Use the correct screwdriver (typically Phillips) and avoid over-tightening to prevent strip or damage
• Disconnect power and follow appliance manufacturer safety instructions when accessing internal parts

This replacement control knob fits stove and oven front panels and restores reliable control of temperature and burner settings. It provides a secure, slip-resistant grip so you can turn settings with confidence. What it does

• Replaces a cracked, stripped, or missing control knob to restore user control
• Slides onto the control shaft for simple push-on operation
• Helps prevent accidental setting changes with a snug fit
• Visible index marker lets you clearly see selected settings

• One control knob

• Typically installs by pulling the old knob straight off the valve or shaft and pushing the new knob into place
• Disconnect power to the appliance or turn controls off before servicing for safety
• If the knob does not seat properly, do not force it—inspect the shaft for damage or debris

These are replacement countertop mounting screws that secure the appliance to the countertop or cabinet, restoring a stable, flush fit and preventing movement or gaps. Sold as a 2-pack for quick, direct replacement. What it does

• Secures the appliance countertop or trim to the cabinet or counter to keep the unit from shifting.
• Helps eliminate rocking, gaps, or uneven alignment caused by missing or loose mounting screws.
• Restores proper fit and finish where original mounting hardware has been lost or damaged.
• Works with factory mounting points and standard driver heads for straightforward replacement.

• Two countertop mounting screws.

• Use the correct-size driver to avoid stripping the screw head.
• Tighten until snug; avoid over-tightening which can strip threads or damage the cabinet/countertop.
• Keep original brackets and hardware; replace only the missing or damaged screws as needed.

This hex flange nut secures components where a broader bearing surface is needed to resist loosening and distribute load. It fits 10-32 threaded studs and is used on fastened assemblies in appliances. What it does:

• Provides a secure threaded connection for 10-32 screws and studs
• Flange spreads clamping force to reduce panel or bracket damage
• Hex shape allows tightening with a wrench for a reliable hold
• Commonly replaces worn or missing nuts that cause loose panels or rattling

• One hex flange nut

• Use the correct 10-32 screw or stud and hand-start threads to avoid cross-threading
• Tighten with an appropriately sized wrench; do not overtighten to prevent thread or part damage
• Disconnect power and follow appliance safety instructions before servicing
• Replace only like-for-like; confirm size and thread match your application

This Box & Wires Assembly replaces the fridge's boxed electrical junction and pre-wired harness to restore reliable power routing between components. It keeps internal wiring organized and protected for safe appliance operation. What it does:

• Provides a sealed junction box and factory-wired harness to connect multiple refrigerator components
• Routes power and signals so lights, controls, and accessories receive electrical feed
• Replaces damaged or burned wiring that can cause intermittent or complete loss of function
• Helps prevent exposed wires and loose connections that increase risk of shorts

• One box and pre-wired harness assembly as shown

• Disconnect power to the appliance before beginning any work
• Match wire colors and connector types to the original assembly; secure wiring and fasteners per OEM routing
• Do not splice or modify the harness; improper wiring can cause damage or safety hazards

This mounting bracket secures appliance components in place to restore stable operation and alignment. It's a simple, durable replacement that helps prevent loose parts and rattling for safer, quieter performance. What it does:

• Provides structural support for internal components and assemblies
• Holds panels, modules or hardware in correct alignment to prevent movement
• Helps eliminate rattling, vibration noise, or loose-fitting parts
• Restores proper fit where a worn or broken bracket allowed misalignment

• Turn off power to the appliance and unplug before beginning work
• Remove only the panels or fasteners necessary to access the old bracket
• Reuse original fasteners or replace with equivalent-size hardware; tighten securely