Frigidaire Bracket & Flange

The Latch Hook is an OEM replacement part for Frigidaire microwaves. It is an internal component that helps securely latch and lock the microwave door during operation. The latch hook works with the door handle mechanism to ensure the door is properly fastened to prevent leaks of microwave energy and for safety. 

Causes of a bad latch hook can include wear and tear over time, damage from repeated use of the door latch, or issues with the latch hook spring or connecting components. 

Symptoms of a bad latch hook include:

• The microwave door not closing or latching securely  
• Difficulty closing or popping open the door during a cycle
• Leaks of microwave energy from around the door seals
• Error codes related to door-latching problems

This OEM Frigidaire replacement part is also compatible with Electrolux, Westinghouse, and Kelvinator microwaves. 

The Lower Hinge Bracket is an OEM part for Frigidaire refrigerators. This bracket supports the refrigerator door, allowing it to pivot smoothly while opening and closing. It ensures that the door remains aligned and operates correctly.

You should replace the lower hinge bracket if it becomes damaged or worn out. Common causes of a bad hinge bracket include wear and tear from frequent use, rust or corrosion, or damage from accidental impacts.

Symptoms of a bad lower hinge bracket include:

• Difficulty in opening or closing the refrigerator door
• The door not aligning properly with the refrigerator body
• Unusual noises when the door is in motion
• Visible damage or rust on the bracket

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Drum Bearing Bracket is an OEM replacement part for Frigidaire dryers. It holds and supports the drum bearing, which allows the dryer drum to spin smoothly during the tumbling and drying cycle.

Causes of failure can be cracking or breaking of the bracket over time due to constant use and stress. Improper installation that puts strain on the bracket may also lead to issues.

Symptoms of a bad drum bearing bracket include:

• Excessive vibration or shaking during operation
• Loud grinding or scraping noises
• The dryer drum not spinning properly or at all
• Premature wear of the drum bearing

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This dishwasher rack tine row bracket secures the fold-down tine row to the rack so it pivots and locks correctly. Replacing a cracked or missing bracket helps restore stable plate support and smooth loading.

• Secures the fold-down tine row to the dishrack
• Allows the tine row to pivot between upright and flat positions
• Helps keep dishes from tipping during cycles
• Common symptoms: tines won't stay up, row flops loosely, bracket is cracked/missing

• Disconnect power to the dishwasher before servicing
• Pull out the rack and locate the affected fold-down tine row
• Release the old bracket and snap the new bracket onto the rack wires
• Verify the tine row pivots and latches smoothly before returning the rack

The Door Release Lever is an OEM part for Frigidaire microwaves. It facilitates the smooth opening of the microwave door by engaging the latch mechanism when the door release button is pressed, ensuring convenient access to the microwave cavity.

Causes of a bad door release lever can include regular wear and tear, exposure to heat, or physical damage from forceful operation.  

Symptoms of a bad Microwave Door Release Lever include:

• Difficulty opening the microwave door
• The door not latching properly or remaining ajar
• The door release button not functioning correctly
• Unusual resistance or noises when opening the door

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Anti-Tip Bracket Kit is an OEM part for Frigidaire ranges and ovens. This part secures the appliance to the floor or wall, preventing it from tipping over when the oven door is opened or when heavy cookware is placed on an open door or extended rack. The kit typically includes a metal bracket, screws, and installation instructions.

Over time, or during instances of moving or remodeling, the anti-tip bracket may become dislodged or may not be reinstalled correctly, which can compromise the safety of the appliance. 

Symptoms of a missing or improperly installed Anti-Tip Bracket include:

• The range or oven tilts forward when pressure is applied to an open door
• The appliance moves more easily than expected when nudged or cleaned
• Visible absence of a bracket at the lower back portion or floor area behind the appliance

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement bracket secures a component to the appliance frame, keeping it aligned and stable during operation. Install it to replace a bent, cracked, or missing bracket and restore a solid, rattle-free mount.

• Provides a rigid mounting point to hold the specified part in place
• Helps maintain alignment to reduce vibration, rubbing, or noise
• Replaces damaged or corroded hardware to restore a secure fit
• Common symptoms: loose or sagging component, unusual vibration/noise, or part shifting out of position

• Disconnect power before servicing; shut off water supply if working near water lines
• Note original orientation and fastener locations; take a reference photo
• Transfer and reuse existing screws/clips as needed; tighten fasteners evenly without over-torquing
• Verify alignment and test operation before final reassembly

This replacement bracket is used in Frigidaire-made dishwashers to secure an associated component or panel. Replacing a broken or missing bracket restores a tight fit, alignment, and stability so parts don't loosen, rattle, or shift during cycles. What it does:

• Provides a rigid mounting point for the connected part or panel
• Maintains proper alignment and stability during operation
• Helps reduce rattling or vibration from a loose component
• Replaces a broken, bent, rusted, or missing bracket

• 1 bracket

• Disconnect power and turn off the water supply before servicing
• Access and mounting location vary by model; refer to your service or installation manual
• Wear cut-resistant gloves; bracket edges may be sharp
• Save and reuse the original screws/fasteners; install in the same orientation and tighten securely

This hinge bracket supports and aligns the refrigerator door at the pivot point, helping the door open and close smoothly and seal properly. Replacing a worn bracket can restore stable door movement and reduce air leaks.

• Provides rigid support for the door hinge to maintain proper alignment
• Helps ensure a consistent door seal to prevent temperature fluctuations
• Common fix for loose, sagging, or misaligned doors
• Helps if the door makes popping/grinding noises when opening or closing

• Unplug the refrigerator and wear cut-resistant gloves
• Support the door before removing hinge fasteners to prevent drops
• Transfer and reinstall existing screws/hinge pin as needed
• Check door alignment and gasket contact after installation

This aluminum strap secures the defrost heater firmly against the evaporator coil to maintain proper contact during defrost. Correct contact improves heat transfer so frost melts evenly and helps prevent recurring ice buildup on the evaporator.

• Secures the defrost heater to the evaporator for proper contact and heat transfer
• Promotes complete, even defrosting across the evaporator coil
• Helps reduce repeat frost/ice accumulation caused by a shifted or loose heater
• Typical clues include a loose heater, uneven frost pattern, or rattling near the evaporator

• Disconnect power and allow ice to melt before accessing the evaporator
• Use care around sharp fins and fragile refrigerant tubing; do not puncture or deform the coil
• Position the heater per your model's parts diagram and tighten the strap for firm, even contact
• Verify wiring is routed clear of the fan and moving parts before reassembly

This refrigerator bracket and bushing assembly secures a moving component and provides a stable wear/pivot surface for smooth operation. Replace it when the original parts are worn or broken and causing looseness, scraping noises, or poor alignment.

• Provides a mounting point and bearing surface for rotational or sliding movement
• Helps maintain alignment and smooth, quiet operation
• Can help address wobble, scraping/binding, or a component that sags or sits out of position
• Replace if the bracket is bent/cracked or the bushing is worn/missing

• Disconnect power before servicing; turn off water supply if working near dispenser lines
• Support the attached component while removing fasteners; note the original orientation
• Transfer any spacers/clips from the old parts if present and tighten fasteners evenly
• After installation, verify smooth movement and proper alignment

This lower hinge bracket supports and aligns the refrigerator door at the bottom pivot point. Replacing a bent or worn bracket restores smooth door movement and proper alignment so the door opens and closes without rubbing or sagging.

• Provides the mounting point for the lower hinge/pin at the cabinet base
• Keeps the door square and aligned for smooth opening and closing
• Common fix for door sagging/drooping or rubbing at the bottom corner
• Helps eliminate scraping, binding, or squeaking from a damaged hinge area
• Replaces cracked, bent, or stripped brackets

• Disconnect power and remove items from the door to reduce weight.
• Support the door; remove the bottom hinge cover and screws, then lift the door off the lower hinge pin.
• Remove the old bracket, transfer any reusable hardware/shims, and install the new bracket securely.
• Reinstall the door, check gaps and gasket contact, adjust as needed, and restore power.

This clock mounting bracket secures the appliance's clock/timer or electronic oven control behind the control panel. It helps keep the display and keypad aligned and stable so the control stays firmly in place.

• Holds the clock/timer or electronic oven control securely to the console
• Maintains proper alignment of the display and keypad with the front bezel
• Replaces a bent, cracked, or missing bracket
• Typical symptoms include a loose or sagging control, rattling in the console, or a misaligned display/keypad

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the console/backguard and remove the rear cover to reach the control and bracket
• Support the control while removing fasteners; transfer it to the new bracket and reuse original hardware as applicable
• Use ESD precautions when handling the electronic control and avoid overtightening screws

This bracket is the factory support used to mount a component securely inside your appliance. Replacing a damaged bracket restores proper alignment and reduces vibration, keeping the part stable so it operates as designed. What it does:

• Provides a rigid mounting point for the designated component
• Maintains correct alignment to help prevent rubbing, rattling, or noise
• Replaces a cracked, bent, or missing bracket to restore secure fit
• Typical signs include vibration, a loose or misaligned part, or visible damage

• 1 bracket

• Disconnect power before servicing
• Wear cut-resistant gloves; cabinet edges can be sharp
• Reuse original screws/fasteners and any spacers or grommets from the old bracket
• Mount in the original position and tighten fasteners evenly without overtightening

This mounting bracket secures internal panels or assemblies to the appliance, restoring proper alignment and reducing movement. A direct-replacement bracket helps stop rattling, keeps parts in place, and supports reliable operation. What it does

• Secures panels, trim, or internal components to the cabinet to maintain proper fit and alignment.
• Prevents vibration and rattling that can occur when brackets are bent, cracked, or missing.
• Restores stable mounting for doors, panels, or assemblies so parts operate smoothly.
• Common symptom: loose or misaligned panels, persistent noise, or visible bracket damage.

• Disconnect power (unplug or shut off circuit) before starting any repair.
• Remove outer panels or trim as needed to access the bracket; keep track of fasteners.
• Inspect surrounding parts and reuse original screws if undamaged; replace hardware if stripped or corroded.

This ice maker mounting bracket secures the ice maker assembly inside the refrigerator so it stays stable and correctly aligned with the water fill tube. Replace a damaged bracket to prevent looseness and restore consistent ice production.

• Supports and positions the ice maker assembly
• Maintains proper alignment with the water fill tube for correct filling
• Damage can cause a loose/sagging ice maker, rattling, water drips near the ice maker, or intermittent/no ice
• Replace if the bracket is cracked, bent, or missing

• Unplug the refrigerator and shut off the water supply before service
• Remove the ice bin and ice maker to access the bracket; reuse existing mounting hardware
• Ensure the fill tube seats correctly and the ice maker sits level before tightening fasteners
• Restore power and water; check for leaks and proper ice maker operation