Parts for Ge DPVH880EJ0MV: 02 - Front Panel Parts

This front opening plug fills the exposed opening on the appliance front and restores the appliance's finished appearance. The desert-silver finish matches factory trim for a clean, like-new look. What it does:

• Covers and protects an unused front access/opening from dust and debris
• Restores the appliance's exterior appearance and factory finish
• Helps maintain a finished bezel around controls or service openings
• Compatible with factory mounting points for a secure fit when installed

• Disconnect power to the appliance before beginning any work
• Typically installs with simple snap-in or screw fasteners; use common hand tools
• Handle part carefully to avoid scratching the finish during installation

This front opening plug is a small replacement trim piece that restores the finished look and seals an unused front access/opening on the appliance. It keeps the opening covered and helps prevent dirt and moisture intrusion. What it does:

• Covers and finishes a front access/opening to restore factory appearance
• Helps keep dust, lint, and moisture out of the opening
• Matches the appliance color for a seamless look (pearl red)
• Simple snap-in design for a secure fit without extra hardware

• One front opening plug (pearl red)

• Turn off and unplug the appliance or disconnect power before starting work
• Remove any damaged trim or remnants before installing the new plug
• Press the plug into the opening until it snaps or seats flush; do not force with excessive tools

This foam gasket seals the top trap/duct cover to help maintain proper airflow and prevent leaks around the duct area. It restores a tight seal where the duct cover meets the cabinet for more reliable performance. What it does:

• Creates a cushioning seal at the top of the trap/duct cover to reduce air and moisture infiltration
• Helps prevent frost build-up or pooling caused by unwanted airflow around the duct area
• Reduces the chance of odors migrating from the drain/trap area into the compartment
• Restores the original fit where a worn or damaged gasket allowed gaps

• One foam gasket, top trap/duct cover

• Disconnect power to the appliance before starting any repair
• Remove the duct or trap cover per the service instructions to access the gasket area
• Clean mounting surfaces of old adhesive, debris, and moisture before installing the new gasket
• Press the gasket firmly into place and reassemble covers and test operation

This white front panel restores the exterior appearance and proper fit of your appliance control area or door. It replaces a damaged, cracked, or faded panel to help keep controls and internal components protected and looking like new. What it does:

• Replaces a worn, dented, cracked, or discolored front panel to restore appearance
• Provides a secure mounting surface for controls, displays, and trim around the door or console
• Helps protect internal components from dust, spills, and impact
• Maintains correct spacing and alignment for door or control operation

• For safety, disconnect power to the appliance before attempting removal or installation
• Handle carefully to avoid bending or damaging mounting tabs and painted surfaces
• Installation may require removal of adjacent trim or the door; keep screws and fasteners organized
• Replace damaged clips or brackets to ensure a secure fit

The Trap Duct Assembly is an OEM part for GE dryers. This part directs the airflow from the dryer drum to the exhaust vent. This assembly ensures efficient drying by guiding hot air out of the dryer while collecting lint and debris in the trap, preventing it from clogging the venting system.

Causes of a bad trap duct assembly can include lint buildup over time, physical damage due to heavy usage, or obstruction from foreign objects. 

Symptoms of a bad Trap Duct Assembly include:

• Reduced drying efficiency or longer drying times
• Excessive lint buildup around the dryer
• Overheating of the dryer
• Unusual noises during the drying cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Kit Felt and Instruction is an OEM part for GE dryers. This kit includes felt seals and instructions necessary for installation. The felt seals help create a barrier between the drum and the front panel, retaining heat inside the dryer and ensuring efficient drying. They also reduce friction and wear on the drum and front panel.

Causes of a bad felt seal can include regular wear and tear, high heat exposure, or damage from foreign objects inside the dryer. A compromised felt seal can lead to inefficient drying and potential damage to the dryer components.

Symptoms of a bad felt seal include:

• Clothes taking longer to dry
• Excessive lint buildup inside the dryer
• Unusual noises during the drying cycle
• Visible damage or gaps in the felt seal

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This top bearing assembly supports the front of the dryer drum and includes felt seals to help maintain proper airflow and reduce noise. Replacing a worn bearing restores smooth drum rotation and helps prevent scraping sounds and fabric snagging. What it does:

• Supports and guides the front of the drum for smooth, quiet operation
• Felt seals help contain heat and airflow for consistent drying
• Restores drum alignment to reduce scraping/squealing and thumping
• Common symptoms include drum dragging or sagging, longer dry times, lint at the door, and black marks on clothes

• 1 top bearing assembly with felt seals

• Disconnect power; shut off gas supply for gas dryers
• Lift the top and remove the front panel; support the drum during service
• Remove the old bearing and install the new assembly, seating the felt seals evenly against the drum opening
• Hand-rotate the drum to ensure smooth travel before reassembly and testing

The Dryer Front Bearing Drum Slide (Green, 2-Pack) is an OEM replacement part for GE dryers. These slides are located on the front panel of the dryer and work to support the drum as it rotates. The green slides are designed to reduce friction between the drum and the panel, ensuring smooth operation and helping to prolong the life of the appliance.

Over time, these slides can wear out due to constant movement, heat, and friction. When worn or damaged, the drum may not rotate as intended, leading to noise and reduced efficiency.

Symptoms of bad dryer front bearing drum slides include:

• Squeaking or grinding noises during operation
• The drum appearing loose or sagging at the front
• Clothes not drying evenly or taking longer to dry
• Visible wear or thinning on the existing drum slides

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This cleaning felt mounts on the dryer's front shroud. It lightly contacts the rotating drum to wipe away lint and residue, helping keep the drum edge clean and supporting consistent airflow to the lint filter.

• Provides a soft wiper against the drum rim to reduce lint and residue buildup
• Helps maintain smooth drum rotation and a clean front duct area
• Wear signs include frayed or missing felt, lint trails on fabrics, or light squeaks at the front
• Visual inspection is recommended if lint accumulates inside the drum after cycles

• Disconnect power; for gas dryers, also shut off gas supply
• Access the front panel/shroud and note the original felt's orientation before removal
• Clean the mounting surface; install the new felt in the same position (some models use clips or adhesive)
• Hand-rotate the drum to ensure even, light contact before reassembly and testing

This replacement part is a screw, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This screw is compatible with many different areas of the appliance. Screws are generally used for keeping parts of the machinery secure and in place during use. It is possible that screws can become loose over time and need to be replaced after years of normal wear and tear.A new screw might be needed if the user notices parts of the appliances are becoming loose or are even falling off. This can be due to screws becoming stripped over time or if the appliance is bumped during transport. The repair for this part is simple. Remove the old screw and replace it with a new part. The only tools needed for this repair are a screwdriver and possibly pliers if the damaged screw is stuck in place.This screw is sold individually and is a genuine OEM replacement part sourced from the manufacturer.

The Door Switch is an OEM part for GE dryers, designed to ensure the dryer does not operate when the door is open. This safety feature is crucial for preventing accidents and ensuring the appliance operates efficiently and safely. The switch signals the dryer's control system about the status of the door—if it's open or closed—thereby allowing or preventing the start of a drying cycle. 

Causes of damage to the door switch often include mechanical wear from repeated use, accidental damage from loading or unloading, or electrical issues such as short circuits. 

Symptoms of a bad Door Switch include:

• The dryer not starting when the door is closed 
• The dryer continuing to run when the door is opened
• Unusual noises or the dryer stopping mid-cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.

• Fastens brackets, covers, and sheet-metal panels as specified in the parts diagram
• Restores proper fit when an original screw is missing, stripped, or damaged
• Helps eliminate rattling or vibration from loose hardware
• Keeps components safely in place during operation

• Disconnect power to the appliance before servicing
• Match length, head style, and thread to the original; install in the same location/quantity
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten, especially into plastic or thin sheet metal

Replacement screw that secures appliance panels and internal components, restoring proper fit and helping prevent rattling or misalignment. Use this fastener when original screws are stripped, missing, or damaged to keep parts stable and secure. What it does:

• Secures panels, trim pieces, brackets and other components to maintain proper alignment and fit.
• Replaces stripped, corroded, or missing screws that can cause rattling, vibration, or loose parts.
• Restores stable mounting for service panels and access covers to reduce noise and movement during operation.
• Simple hardware replacement — helps prevent secondary damage caused by loose or shifted components.

• Disconnect power or gas (when applicable) before servicing to avoid shock or injury.
• Use the correct screwdriver or bit to avoid stripping the head; turn until snug—do not overtighten.
• Keep track of small parts and wear eye protection when working in tight spaces.
• If threads are damaged, replace with the correct OEM screw rather than forcing reuse.

The Door Strike is an OEM part for GE dryers. This component is crucial for ensuring that the dryer door latches properly when closed. It interacts with the door catch mechanism to secure the door during operation, preventing it from opening unexpectedly, which ensures the dryer operates safely and efficiently.

Symptoms of a failing Door Strike include:

• The dryer door not staying closed during a cycle
• Difficulty in closing the dryer door or getting it to latch properly
• The dryer not starting because the door switch is not engaged
• Visible damage or wear on the door strike

Causes of a bad door strike can include wear and tear from regular use, physical damage from slamming the door or mishandling, and misalignment caused by repeated opening and closing.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: If the door catch is also needed, use part number WE1M1011.

This strike plate mounts at the door opening and works with the door latch/strike to keep the appliance door securely closed during operation. Replacing a worn plate helps restore positive latching and reliable cycle start/stop via the door switch.

• Provides the catch surface for the door latch/strike to engage
• Helps keep the door closed and properly aligned
• Enables the door switch to engage so the cycle can run
• Common symptoms include: door won't stay closed, door pops open, unit won't start unless the door is pressed, visible wear or bending on the plate

• Disconnect power before servicing
• Open the door and remove the screws securing the existing plate
• Align the new plate with the latch/strike and fasten securely with the existing hardware
• Test door closure and latch engagement; adjust alignment if necessary

This Nut-Strip Door Guide secures the door guide/strip to the appliance, helping keep the door aligned and operating smoothly. Replace a worn or missing nut to restore proper fit and prevent the guide from loosening. What it does

• Fastens the door guide/strip to the appliance frame or door
• Keeps the door guide stable to maintain proper door alignment
• Helps prevent the guide or trim strip from shifting or falling off
• Commonly replaced when the guide is loose, missing, or stripped

• Disconnect power to the appliance before beginning any repair.
• Use appropriate hand tools (screwdriver/socket) and avoid over-tightening to prevent damage.
• Inspect the door guide/strip and surrounding fasteners; replace any damaged parts for proper fit.

This screw is a factory replacement fastener used to secure appliance panels and components. It restores lost or loose hardware so parts sit correctly and operate without rattling or movement. What it does

• Secures panels, brackets, and small components to the appliance frame
• Restores proper alignment and helps eliminate rattling or vibration
• Replaces missing or stripped fasteners that prevent parts from staying fixed
• Matches OEM fit for reliable fastening where the original screw was used

• One replacement screw

• Use the correct-size screwdriver or driver bit to avoid stripping the head
• Power off and unplug the appliance before accessing internal components
• Tighten snugly but avoid overtightening to prevent thread damage
• Keep removed hardware organized so you can install replacements in the original locations

This metal mounting plate supports the dryer door strike/catch interface. It provides a solid anchor point so the door latches securely, helping the dryer start and run only when the door is properly closed.

• Reinforces the latch area to keep the door securely closed
• May help when the door won't stay shut or the dryer won't start unless the door is held closed
• Useful if the existing plate is bent, loose, or missing
• Helps prevent vibration-related door pops during a cycle

• Unplug the dryer before servicing
• Open the door and remove fasteners securing the old plate; retain hardware if reusable
• Position the new plate and tighten screws evenly—do not overtighten
• Test door closure and latch engagement before restoring power

This door guide aligns and supports the dryer door as it closes so the strike engages the catch cleanly. Replacing a damaged or missing guide restores smooth, secure latching and reduces gaps that can affect drying performance.

• Guides the door into position for proper latch engagement
• Helps maintain door alignment to prevent gaps, rubbing, or rattling
• Addresses issues like difficulty closing, door popping open, or misalignment
• Direct replacement for a worn, cracked, or missing guide

• Disconnect power to the dryer before servicing
• Open the door and remove the screws or clips securing the existing guide
• Position the new guide and fasten with the original hardware
• Test door operation to ensure smooth latching and proper alignment

The Trap Duct Assembly is an OEM part for GE dryers. This part directs the airflow from the dryer drum to the exhaust vent. This assembly ensures efficient drying by guiding hot air out of the dryer while collecting lint and debris in the trap, preventing it from clogging the venting system.

Causes of a bad trap duct assembly can include lint buildup over time, physical damage due to heavy usage, or obstruction from foreign objects. 

Symptoms of a bad Trap Duct Assembly include:

• Reduced drying efficiency or longer drying times
• Excessive lint buildup around the dryer
• Overheating of the dryer
• Unusual noises during the drying cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.