Parts for Ge PFDN445GL0MV: 02 - Front Panel Parts

This front opening plug fills the exposed opening on the appliance front and restores the appliance's finished appearance. The desert-silver finish matches factory trim for a clean, like-new look. What it does:

• Covers and protects an unused front access/opening from dust and debris
• Restores the appliance's exterior appearance and factory finish
• Helps maintain a finished bezel around controls or service openings
• Compatible with factory mounting points for a secure fit when installed

• Disconnect power to the appliance before beginning any work
• Typically installs with simple snap-in or screw fasteners; use common hand tools
• Handle part carefully to avoid scratching the finish during installation

This front opening plug is a small replacement trim piece that restores the finished look and seals an unused front access/opening on the appliance. It keeps the opening covered and helps prevent dirt and moisture intrusion. What it does:

• Covers and finishes a front access/opening to restore factory appearance
• Helps keep dust, lint, and moisture out of the opening
• Matches the appliance color for a seamless look (pearl red)
• Simple snap-in design for a secure fit without extra hardware

• One front opening plug (pearl red)

• Turn off and unplug the appliance or disconnect power before starting work
• Remove any damaged trim or remnants before installing the new plug
• Press the plug into the opening until it snaps or seats flush; do not force with excessive tools

Red mounting screw for dryer assembly. Secures internal panels and components. Order replacement if original screw is stripped, missing, or damaged.

White #10-16 mounting screw for dryer assembly. Secures internal components like drum supports and bearing slides. Order replacement screws.

Gold-colored screw for dryers. Secures panels, brackets, or internal components. Replace if missing, stripped, or damaged during repairs or maintenance.

This foam gasket seals the top trap/duct cover to help maintain proper airflow and prevent leaks around the duct area. It restores a tight seal where the duct cover meets the cabinet for more reliable performance. What it does:

• Creates a cushioning seal at the top of the trap/duct cover to reduce air and moisture infiltration
• Helps prevent frost build-up or pooling caused by unwanted airflow around the duct area
• Reduces the chance of odors migrating from the drain/trap area into the compartment
• Restores the original fit where a worn or damaged gasket allowed gaps

• One foam gasket, top trap/duct cover

• Disconnect power to the appliance before starting any repair
• Remove the duct or trap cover per the service instructions to access the gasket area
• Clean mounting surfaces of old adhesive, debris, and moisture before installing the new gasket
• Press the gasket firmly into place and reassemble covers and test operation

This white front panel restores the exterior appearance and proper fit of your appliance control area or door. It replaces a damaged, cracked, or faded panel to help keep controls and internal components protected and looking like new. What it does:

• Replaces a worn, dented, cracked, or discolored front panel to restore appearance
• Provides a secure mounting surface for controls, displays, and trim around the door or console
• Helps protect internal components from dust, spills, and impact
• Maintains correct spacing and alignment for door or control operation

• For safety, disconnect power to the appliance before attempting removal or installation
• Handle carefully to avoid bending or damaging mounting tabs and painted surfaces
• Installation may require removal of adjacent trim or the door; keep screws and fasteners organized
• Replace damaged clips or brackets to ensure a secure fit

Replaces a broken, cracked, or damaged lint trap duct assembly in your dryer. Directs airflow from the drum to the exhaust vent and houses the lint trap.

Seals the gap between the dryer drum and front panel to retain heat and reduce friction. Replace if worn, torn, or causing the drum to slip out of place.

Top drum bearing with seals supports smooth dryer drum rotation. Replace if dryer squeals, thumps, or drum wobbles. Confirm fit with your model number.

Illuminates your dryer drum for better visibility when loading and unloading clothes. Replace when burned out or flickering. Verify fit with your model.

The Dryer Front Bearing Drum Slide (White, 2-Pack) is an OEM replacement part for GE dryers. These slides are located on the front panel of the dryer and work to support the drum as it rotates. The white slides are designed to reduce friction between the drum and the panel, ensuring smooth operation and helping to prolong the life of the appliance.

Over time, these slides can wear out due to constant movement, heat, and friction. When worn or damaged, the drum may not rotate as intended, leading to noise and reduced efficiency.

Symptoms of bad dryer front bearing drum slides include:

• Squeaking or grinding noises during operation
• The drum appearing loose or sagging at the front
• Clothes not drying evenly or taking longer to dry
• Visible wear or thinning on the existing drum slides

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Dryer Front Bearing Drum Slide (Green, 2-Pack) is an OEM replacement part for GE dryers. These slides are located on the front panel of the dryer and work to support the drum as it rotates. The green slides are designed to reduce friction between the drum and the panel, ensuring smooth operation and helping to prolong the life of the appliance.

Over time, these slides can wear out due to constant movement, heat, and friction. When worn or damaged, the drum may not rotate as intended, leading to noise and reduced efficiency.

Symptoms of bad dryer front bearing drum slides include:

• Squeaking or grinding noises during operation
• The drum appearing loose or sagging at the front
• Clothes not drying evenly or taking longer to dry
• Visible wear or thinning on the existing drum slides

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Wipes lint and residue from the drum edge to maintain airflow and prevent buildup. Replace when worn, torn, or dislodged. Confirm fit with your model.

Replacement screw for securing dryer components like drum supports, panels, and housings. Needed when screws are lost, stripped, or damaged during repair.

Foam gasket seals the air duct connection in your dryer, preventing heat loss and improving efficiency. Replace if torn, compressed, or causing noise.

If your dryer won't power on or has intermittent electrical issues, the terminal block may be damaged. This socket assembly restores safe power connections.

Dryer won't start or humming when you press start? The door switch signals when the door is closed. Easy 15-minute DIY repair with basic tools.

Replacement screw secures dryer panels, brackets, and internal components. Replace stripped, lost, or damaged screws to eliminate rattles and maintain assembly.

Mounting screw secures panels and trim on dishwashers. Replace missing, stripped, or damaged fasteners to keep components aligned and vibration-free.

Replacement screw for securing dryer panels and internal components. Restores proper fit when original screws are stripped, missing, or damaged.

Dryer door won't stay closed? A worn or broken door strike prevents proper latching. Easy 5-minute DIY fix with basic tools. Video guide included.

Secures dryer panels, brackets, and internal assemblies. Replace missing, stripped, or damaged screws to restore proper alignment and prevent vibration.

Dryer door won't latch or stay closed? This strike plate mounts at the door opening to catch the latch securely. Easy DIY repair for reliable closing.

Secures the door guide strip to your dryer frame, keeping the door aligned. Replace this nut if it's missing, stripped, or worn to restore proper fit.

Dryer door won't stay closed or pops open during cycle? This mounting plate anchors the door strike for secure latching. Quick DIY fix with video guide.

Aligns and supports your dryer door for smooth closing and secure latching. Replace if cracked, broken, or missing to eliminate gaps and restore fit.

Replaces a broken, cracked, or damaged lint trap duct assembly in your dryer. Directs airflow from the drum to the exhaust vent and houses the lint trap.

Left-side door hinge bracket for dryers. Secures the door to the frame for smooth opening and closing. Replace if cracked, broken, or missing.

Right-side door hinge bracket for dryers. Secures the door hinge assembly to the dryer frame. Replace if cracked, bent, or broken for proper alignment.

This is a hinge base screw used to secure a door hinge assembly so the door stays aligned and operates smoothly. It replaces a worn, missing, or damaged hinge screw to restore proper hinge fit. What it does:

• Secures the hinge base to the cabinet/frame to keep the door aligned
• Prevents door sagging, misalignment, or uneven gaps
• Stops loose-hinge noise or clunking during door movement
• Restores stable pivoting for smooth opening and closing

• One hinge base screw

• Disconnect power to the appliance and support the door before removing hinge hardware
• Use the correct screwdriver or bit to avoid stripping the screw head
• Thread carefully and do not overtighten to prevent damage to the hinge or mounting surface
• If other hinge components are worn or damaged, replace them as well for best results