General Electric Microwave Grille

The Vent Grille is an OEM part for GE microwaves. It is located at the top of the microwave, allowing proper ventilation by covering the exhaust opening while protecting internal components from debris and dust.

Causes of a bad vent grille can include cracking or breaking due to impact, warping from prolonged exposure to heat, or discoloration from grease and food particles. A damaged vent grille can impede proper ventilation, potentially leading to overheating and reduced efficiency of the microwave.

Symptoms of a bad Vent Grille include:

• Visible cracks or breaks in the grille
• Warping or melting of the plastic
• Discoloration or buildup of grease and grime

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The GE grille vent is an OEM replacement part responsible for allowing airflow and ventilation in the microwave. The grille vent is typically located on the front of the microwave, near the top, or on the sides. It serves as an outlet for heat and steam generated during cooking, helping to prevent the accumulation of excess moisture and maintaining proper airflow within the appliance.

The GE grille vent can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

Dimensions:

• Depth - 29.625  in
• Height - 2.25  in
• Width - 3.5  in

This part fixes the following symptoms:

• Restricted airflow or poor ventilation inside the microwave
• Excessive heat buildup or overheating during cooking
• Steam or condensation remaining inside the microwave after use
• Visible damage, such as cracks, breaks, or warping, to the grille vent
• Inability to properly attach or secure the grille vent

This upper vent grille assembly replaces the front top grille on your microwave. It directs airflow through the louvers and restores a secure, finished look while helping shield the filter area and internal components from accidental contact.

• Channels exhaust or recirculating air through the top-front opening
• Shields the filter compartment and cabinet edge from debris and touch
• Provides a finished appearance; helps minimize vibration when properly secured
• Replace if cracked, warped, mounting tabs are broken, or the grille won't stay in place

• Disconnect power before servicing; support the microwave if needed
• Remove the top screws, slide the grille to release the tabs, then lift off; install the new grille in reverse order
• Do not overtighten screws into plastic
• The grille is fully seated and clear of the door swing

Grille assembly replaces the front vent and control-area trim on your range or oven, restoring a clean appearance and directing exhaust airflow. Ideal when the original grille is cracked, bent, loose, or missing. What it does:

• Covers the front vent/control area for a finished, factory look.
• Replaces cracked, dented, loose, or missing grille pieces that cause visible damage or rattling.
• Helps direct exhaust airflow out of the vent opening and keeps the area tidy.
• Uses the appliance's original mounting points for a direct replacement.

• Always disconnect power to the appliance before beginning any repairs.
• Installation typically requires removing the lower access panel or control trim to reach mounting screws/clips.
• Use common hand tools; handle the grille gently to avoid scratching the finish.

This oven grille trims the front of the range or built-in oven, restoring a finished appearance and helping direct airflow. Replaces a damaged or missing front trim to improve fit and finish. What it does:

• Covers and protects the gap between the oven cavity and control/face trim
• Directs vented airflow away from the control area for proper airflow routing
• Restores the oven's factory appearance when original grille is cracked, warped, or discolored
• Helps prevent small debris from entering the vent opening

• One grille trim piece

• Designed for direct replacement; verify fit to your specific model before installation
• Remove power to the appliance before beginning any removal or installation
• Use appropriate hand tools and avoid over-tightening fasteners to prevent cracking

This grille assembly replaces the refrigerator's lower kickplate to restore proper airflow and give the front a finished look. It helps protect internal components while keeping the appliance visually complete. What it does:

• Covers and protects the condenser area and components behind the lower front of the appliance
• Allows proper airflow at the cabinet base to support cooling performance
• Restores the appliance's appearance when the original grille is damaged or missing
• Helps keep pets, debris and small objects out of the lower service area

• Disconnect power to the appliance before beginning work
• Typically secures with screws or retaining clips along the toe-kick; keep hardware from the original part if present
• Align mounting tabs and engage clips/screws without forcing to avoid breakage