General Electric Microwave Bracket & Flange

The Microwave Exhaust Adapter is an OEM replacement part for GE built-in microwave ovens. Located at the top or rear of the microwave, the exhaust adapter connects the ventilation system that removes steam, smoke, and odors produced during cooking. 

Symptoms of a bad exhaust adapter can include: 

• Moisture or steam films accumulating on interior surfaces   
• Strange vibration noises coming from the ventilation connection
• Reduced cooking efficiency as hot air lingers inside the cavity
• Visible cracks, separations, or blockages in the adapter itself

Causes of a bad exhaust adapter microwave include natural wear from repeated heating cycles, cracks or damage from installation/removal, or blockages from grease/ residue accumulation over time.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore built-in microwave models. 

The Lower Lever Switch is an OEM replacement part for GE microwaves. This component activates the door interlock switch when the microwave door is closed. It ensures that the microwave only operates when the door is securely closed, preventing any operational hazards.

Symptoms of a bad Lower Lever Switch include:

• The microwave not starting, indicating the door isn't recognized as closed
• The appliance operating with the door open, a clear safety hazard
• Unusual sounds or issues when attempting to start the microwave
• The need to apply extra pressure to keep the door closed

Common causes for a malfunctioning Lower Lever Switch can be attributed to mechanical wear from frequent use, damage incurred during cleaning or use, or internal issues affecting the switch’s activation mechanism.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Switch Holder is an OEM part for GE microwaves. It securely holds the door switches in place, ensuring that the microwave operates correctly and safely. The door switches detect whether the microwave door is closed, enabling the appliance to start cooking.

Causes of a bad switch holder can include repeated opening and closing of the microwave door, exposure to heat and moisture, or general wear and tear over time.

Symptoms of a bad switch holder include:

• The microwave not starting or stopping unexpectedly
• The door not latching properly
• Error messages related to door issues
• Loose or misaligned door switch

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This latch board is the molded bracket that holds and aligns the door interlock switches and latch levers behind the front panel. Replacing a cracked or warped board restores proper door engagement so the appliance can start and operate safely.

• Supports and positions the door interlock switches and latch levers for correct operation
• Ensures the safety interlock sequence completes when the door closes
• Typical symptoms of failure: won't start, door-related error, or stops when the door is jostled
• Visible cracks or distortion around switch mounts or latch slots

• Disconnect power at the breaker before servicing; follow manufacturer safety procedures
• Access typically requires removing the grille and/or control panel to reach the latch area
• Transfer existing door switches and mounting hardware to the new board, matching orientation
• After reassembly, verify smooth door closure and proper switch actuation

The Door Latch Board is an OEM part for GE microwaves. The latch board controls the door latching mechanism that secures the microwave door closed during operation. It works alongside the door interlock switch to initiate the removal of power to the magnetron when the door is opened, for safety during use. 

Symptoms of a bad latch board include: 

• The door not closing and latching properly  
• The microwave operating with the door open
• Error codes or blinking lights related to the door interlock system
• Issues engaging or disengaging the door-locking mechanism

This replacement part is also compatible with Hotpoint and Profile microwaves. 

This latch body is the door latch component that secures the appliance door during operation, restoring reliable closure so cycles can run normally. Use it to replace a worn or damaged latch that won't hold the door closed. What it does:

• Engages the door striker to hold the door closed and maintain a proper seal during operation
• Works with the door latch mechanism so the appliance can complete cycles that require a closed door
• Common symptom: door won't stay closed, is difficult to latch, or feels loose at the latch point
• Replacing a damaged latch body can prevent intermittent door-open errors and restore normal door operation

• Disconnect power (unplug or turn off circuit breaker) before starting any repair
• Remove the door or access panel as needed; keep track of fasteners and any trim pieces
• Handle door glass and trim carefully to avoid damage; test latch engagement before full reassembly

Replacement mounting bracket that secures internal panels or components to the appliance frame, restoring alignment and stability. Use this bracket to replace cracked, bent, or missing supports that cause vibration or loose parts. What it does:

• Supports and secures panels, trim, or internal assemblies to keep components properly aligned.
• Reduces rattling, sagging, or movement caused by a broken or missing bracket.
• Restores stable mounting after impact, wear, or stripped mounting points.
• Helps maintain proper fit and operation of adjacent parts by providing a solid attachment point.

• Disconnect power (and water/gas if applicable) before starting any repair.
• Basic hand tools required; remove adjacent panels or trim for access as needed.
• Retain original fasteners when possible; replace damaged clips or screws.

The Latch/Switch Holder (Right Side) is an OEM component specifically designed for GE microwaves. It is responsible for securely mounting the latch and door switch components on the right side of the microwave door. 

Symptoms of a bad latch/switch holder include:

• Loose, unstable, or improperly functioning door latch 
• Inoperative or faulty door switch preventing the microwave from operating  
• Physical damage or cracks in the holder plastic

Causes can include normal wear over time exposing internal wires, moisture damage compromising electronics or impact damage weakening the holder structure.

This GE replacement is compatible with Hotpoint, RCA, and Kenmore models.

This lamp bracket secures the oven/range light assembly in place so the bulb and socket stay aligned for reliable interior lighting. It restores a stable fit when the lamp or housing is loose or mispositioned. What it does:

• Holds the lamp socket or housing firmly to the appliance cavity to prevent movement and rattling.
• Maintains proper lamp alignment so the bulb illuminates the cooking cavity as intended.
• Helps reduce intermittent lighting or poor contact caused by a loose bracket.
• Fits into the lamp/light housing area and provides a mounting point for the bulb assembly.

• One lamp mounting bracket.

• Disconnect power to the appliance before starting any repair to avoid shock hazard.
• Remove the bulb and any trim or covers to access the bracket; handle the bulb with gloves or a cloth.
• Typical installation uses basic hand tools; keep track of screws and orientation for reassembly.
• If wiring or the lamp socket is damaged, inspect and replace those components separately.

This metal bracket supports and secures the range/oven control panel so buttons and display stay aligned and stable during use. It restores a solid mount and correct panel fit for safe, reliable operation. What it does:

• Secures the control panel to the console so switches and display remain properly aligned
• Prevents the control panel from sagging, rattling, or shifting when using controls or cleaning
• Restores correct spacing and fit for front-facing controls and trim
• Helps eliminate intermittent contact issues caused by a loose panel

• One control panel bracket

• Disconnect power at the breaker before starting any work
• Basic hand tools (screwdriver/socket) are typically required; avoid force when removing trim
• Keep track of screws and clips—reinstall in original locations to ensure proper fit

This mounting bracket provides a secure support point for appliance components, restoring proper alignment and stability. Use it to replace a bent, broken, or missing bracket to stop rattling and prevent parts from shifting. What it does:

• Secures panels, assemblies, or internal components in their correct position
• Restores stability to reduce vibration, noise, and misalignment issues
• Replaces damaged or corroded brackets that allow parts to sag or move
• Matches OEM fit and mounting points for reliable reinstallation

• Install with the appliance unplugged or power/gas disconnected for safety
• Keep original fasteners when possible; replace any stripped or damaged screws
• Hand-start fasteners, then tighten to secure without over-torquing