General Electric Room Air Conditioner Touch Pad

This drive PWB supplies and regulates power to a driven component in your appliance, ensuring the motor receives the correct signals for smooth, reliable operation and restoring function when the original board fails.

• Provides regulated power and control signals to a motor or actuator
• Interfaces with the main control to manage operation
• On-board components help protect the circuit from faults
• Common symptoms of a failing board: motor won't run or is intermittent, only one speed works, erratic surging, or visible burn marks/clicking from the board area

• Disconnect power before servicing; verify no voltage is present
• Handle the board by the edges and avoid static discharge
• Photograph/document all connectors; transfer them one at a time
• Reinstall using original hardware; keep wiring clear of moving parts

This Drive PWB is the replacement electronic board that controls the appliance's drive functions, restoring reliable motor and transmission commands for normal operation. What it does

• Controls drive motor speed and direction and sends/receives signals to the main control
• Can resolve symptoms such as no spin/agitate, erratic drive behavior, or unresponsive drive controls
• Re-establishes communication between drive assembly and console when board failure is the cause
• Works as the direct replacement board for the drive electronics in compatible units

• Disconnect power to the appliance before service to avoid shock—verify unit is de-energized
• Handle the board by its edges and avoid touching components; observe basic ESD precautions
• Reconnect all connectors in their original positions and secure mounting hardware

This control base assembly is the molded housing that holds the appliance's user-interface components. Replacing a damaged base restores proper alignment and secure mounting of the control board, switches, and display for dependable operation.

• Provides structural support and mounting points for the control board, switches, and display in the control area
• Keeps buttons/knobs aligned for smooth, consistent actuation
• Helps protect and organize wiring within the control panel
• Typical symptoms: cracked or broken housing, loose or sunken controls, buttons sticking or not lining up, rattling/vibration from the control area

• Disconnect power to the appliance before servicing
• Remove the control panel/console to access the base; retain screws and clips for reuse
• Transfer existing control components and wiring to the new base in the same positions
• Avoid overtightening screws into plastic; verify button travel and alignment before reassembly

This main control PWB is the appliance's primary electronic control board that manages user inputs and cycle functions, restoring normal control when a faulty board causes operational issues. What it does:

• Receives user commands and runs appliance control algorithms
• Powers and updates the touchpad/display and indicator lights
• Manages timing, relay switching, and communication with sensors
• Common symptom: appliance won't start, has a blank or erratic display, or shows control-related error codes
• Helps correct unresponsive buttons, intermittent operation, or unexpected cycle behavior when board failure is confirmed

• Disconnect power (unplug or shut off breaker) before accessing the control board
• Handle the PWB by its edges and avoid static discharge; use ESD protection if available
• Refer to the appliance wiring diagram and service manual for proper connector placement and safety procedures

This electronic control unit replaces the oven/range control board to restore normal control and display functions. It provides the interface that manages cook cycles, timing, and user inputs for safe, reliable operation. What it does:

• Manages oven/range control logic, timers and display functions
• Responds to touchpad/knob commands and signals heating elements or igniters
• Helps stop erratic cycling, unresponsive controls or incorrect cook times
• Resolves blank or incorrect display, or loss of control panel responsiveness

• Disconnect power at the breaker or unplug the appliance before starting
• Handle the board carefully; avoid touching circuitry and use anti-static precautions
• Use basic hand tools to access the control panel; keep fasteners for reassembly

This control sheet is a thin insulating/ protective console panel that helps shield the appliance control assembly from heat, moisture, and debris for reliable keypad and electronics performance. It restores proper protection behind the control area. What it does:

• Provides a protective barrier behind the console to help prevent heat and moisture damage to control electronics
• Helps keep dust and debris away from the control board and keypad assembly
• Maintains the original spacing/insulation between the control and inner cabinet components
• Helps reduce the chance of shorts or corrosion caused by stray moisture

• One control sheet/console insulation panel

• Recommended for repair by someone comfortable working with appliance control panels
• Disconnect power (unplug or shut off breaker) before removing the console or accessing the control area
• Handle the control sheet gently to avoid tearing; reassemble fasteners in their original positions