Parts for Whirlpool CAE2745FQ0: 06 - Gearcase, Motor And Pump Parts

The Drain Pump is an OEM part for Whirlpool washing machines. This component is essential for removing water from the washer during the drain cycle. It ensures that water is efficiently pumped out of the washing machine, preventing water from remaining in the tub after a wash cycle, which is crucial for the appliance's proper operation and the cleanliness of your laundry.

You should replace the drain pump if it becomes faulty or stops working. Common causes of a bad drain pump include blockages from debris or lint, wear and tear over time, or electrical malfunctions. These issues can prevent the pump from effectively draining water.

Symptoms of a bad drain pump include:

• Water not draining from the washing machine
• Unusual noises during the drain cycle, such as humming or grinding
• The washer stopping mid-cycle with water still in the tub
• Error codes related to draining issues on the washer's display

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This factory fastener secures appliance panels and components for a tight, rattle-free fit. Replace a missing, stripped, or corroded screw to keep assemblies aligned and performing as intended.

• Fastens panels, brackets, or assemblies in place
• Helps reduce vibration and rattling caused by loose hardware
• Maintains proper alignment of parts to prevent premature wear
• Common signs you need it: missing screw, loose panel, vibration/buzzing noises, or hardware that won't tighten

• Disconnect power; for gas or water-connected appliances, shut off supply lines before service
• Match the screw to the original; verify size, length, and thread before installation
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Snug only—do not overtighten, especially into plastic or thin sheet metal

The Internal Drain Hose is an OEM replacement part for Whirlpool washing machines. It routes used wash water from the tub to an external drain source. 

Causes of a faulty internal drain hose can include cracks developing from constant use or obstructions blocking effective drainage.

Symptoms of a bad internal drain hose include: 

• Water leaks inside or around the base of the washer
• Incomplete drainage of water at the end of cycles  
• Accumulation of dirty water inside the machine

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This is a washing machine gearcase. The purpose of the gearcase is to drive the agitator and spin the basket within the washing machine. When the gearcase stops working correctly, the water may not drain from the clothing after the spin cycle. The user may also notice a burning odor that comes from the washing machine while it's in operation. Sometimes, the washing machine will attempt to agitate and run the spin cycle at the same time. If this is the case, the gearcase needs to be replaced. The appliance will need to be unplugged before replacing this part. Wear gloves to protect the hands for this process.This component is compatible with washing machines that are manufactured by Whirlpool, Kenmore, and Maytag. It is sold individually. This is a genuine OEM replacement part that comes straight from the manufacturer. It's high quality and made to last.

This replacement 7-2-1 screw secures components in compatible Whirlpool appliances, providing a dependable fastener for panels and assemblies. Use it to restore proper fitment and reduce rattling or loose parts. What it does

• Fastens trim, panels, brackets, or internal assemblies to keep parts secure
• Helps stop vibration-related noise from loose components
• Restores correct mounting where the original screw is missing or damaged
• Matches the form and fit of the OEM fastener for intended attachment points

• One replacement 7-2-1 screw

• Use the correct driver to avoid stripping the screw head
• Hand-start threads before tightening to prevent cross-threading
• Tighten until snug—do not over-tighten to avoid damaging plastic or sheet-metal parts
• Disconnect power to the appliance before accessing internal areas

The Drive Motor is an OEM part for Whirlpool washing machines. The drive motor is responsible for powering the agitator or impeller as well as drum rotation during all cycles. It converts electrical energy into mechanical motion needed for washing and spinning laundry.

Causes of a bad drive motor can include failure to start, inconsistent speeds or intermittent operation which are tell-tale signs of normal wear and tear over time.

Symptoms of a failed drive motor include:

• The washer not starting or completing cycles
• Abnormal sounds such as grinding or clicking during operation
• Noticeable vibrations compared to typical wash cycles
• Inability to spin or properly agitate clothing

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Belt is an OEM part for Whirlpool washing machines. It is a crucial transmission component that connects the motor to the drive system transmitting power to the tub. During rotation, the belt spins the tub and agitates or extracts water as needed. 

Causes of a bad belt include general wear and tear over time, exposure to abrasive debris, or damage due to seizing components.  

Symptoms of a failed or slipping belt include:

• Abnormal vibrations or noises during the operation
• Slow or inefficient agitation or spin cycles   
• The tub fails to turn despite a running motor

Replacing with a new OEM belt restores lost power ensuring efficient, balanced operation. Extend the life of your washer with this genuine Whirlpool part.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Actuator is an OEM part for Whirlpool washing machines. This component plays a crucial role in engaging the washer's gear case, enabling the transition between the agitation and spin cycles during a wash. The actuator ensures that the washer drum operates correctly by controlling these mechanical movements.

Over time, the actuator can wear out or fail due to continuous use, mechanical stress, or electrical issues. Replacing a faulty actuator is essential to maintain the proper functioning of the washing machine.

Symptoms of a bad actuator include:

• The washer failing to agitate or spin
• Unusual noises during the wash cycle, such as clicking or buzzing
• The drum not transitioning smoothly between cycles
• Error codes displayed on the washer's control panel

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Capacitor is an OEM part for Whirlpool washers. It is responsible for starting the motor and keeping it running smoothly during the washing cycle. It stores electrical energy and delivers it to the motor when needed, providing the necessary power for the washer to function properly.

A bad washer capacitor can occur due to electrical malfunctions, wear and tear, or damage to the capacitor itself. If you notice symptoms such as the washer not starting or spinning, the motor making unusual noises, or the washer not completing cycles, it may be time to replace the washer capacitor.

Symptoms of a bad washer capacitor include:

• Washer not starting or spinning
• Unusual noises coming from the motor
• Incomplete cycles or erratic behavior

Repair your washer by replacing the faulty or worn-out washer capacitor with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This pulley cover encloses the drive belt and motor pulley at the base of the appliance. It protects moving parts from debris and contact, helping reduce noise and wear when the original cover is cracked, warped, or missing.

• Covers the drive belt and motor pulley to keep out dust and debris
• Helps prevent foreign objects from contacting moving parts
• Restores proper clearance to reduce rubbing or scraping noises
• Common signs it's needed: cracked/missing cover, rattling from the base, visible rub marks on the cover or belt

• Disconnect power and, if applicable, shut off water supply before servicing
• Access the underside per your service manual; support the unit securely if tilting
• Reuse existing mounting screws; do not overtighten to avoid damaging the plastic
• Rotate the belt/pulley by hand after installation to confirm free movement and no contact

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

The Drive Clutch Kit is an OEM replacement part for Whirlpool washing machines. As an integral transmission component, it includes the clutch that engages the drive motor to rotate the central agitator or impeller. 

Causes of a bad clutch kit include worn parts that have aged from repeated use. Signs include slipping, grinding, or clicking noises from the transmission area.

Symptoms of a faulty clutch kit are:

• The washer tub failing to turn or agitate clothes during wash cycles  
• Delayed starts or intermittent rotation
• Vibration or shaking sensed from the frontloader or toploader

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.