Parts for Kenmore 110.31312021 (11031312021, 110 31312021): Gearcase, Motor And Pump Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Washer loud during spin? Grinding or jet engine noise usually means failed bearings in the gearcase. Includes bearings and seals. Moderate difficulty repair.

This replacement 7-2-1 screw secures components in compatible Whirlpool appliances, providing a dependable fastener for panels and assemblies. Use it to restore proper fitment and reduce rattling or loose parts. What it does

• Fastens trim, panels, brackets, or internal assemblies to keep parts secure
• Helps stop vibration-related noise from loose components
• Restores correct mounting where the original screw is missing or damaged
• Matches the form and fit of the OEM fastener for intended attachment points

• One replacement 7-2-1 screw

• Use the correct driver to avoid stripping the screw head
• Hand-start threads before tightening to prevent cross-threading
• Tighten until snug—do not over-tighten to avoid damaging plastic or sheet-metal parts
• Disconnect power to the appliance before accessing internal areas

This WASHER  is an OEM part specifically designed for Whirlpool top-load washing machines. Tailored to fit seamlessly, this component ensures the efficient operation of the washer. It plays a crucial role in maintaining the stability and balance of the machine during the washing cycles.

A damaged or worn-out top-load washer can negatively impact the appliance's performance. Causes of a defective washer might include prolonged use, physical damage, or exposure to excessive weight or force, resulting in instability or imbalance during operation.

Symptoms of a bad WASHER may include:

• Excessive vibration or shaking during the wash cycle
• Difficulty in maintaining balance while spinning
• Noisy or erratic behavior during the operation

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

Fix a washer that won't spin or agitate properly. This drive motor powers the wash basket rotation. Moderate DIY repair, typically 15-30 minutes.

Mounting screw for laundry center and washer units. Secures internal components and panels. Replace if stripped, missing, or damaged during repairs.

Washer making loud grinding noise during spin or agitation? Drive clutch kit repairs worn clutch assembly. Moderate DIY repair, typically 30-45 minutes.

Transmits power from motor to tub for spinning and agitation. Replace if squealing, squeaking, or washer won't spin. Confirm fit with your model number.

Plastic shroud that protects the drive pulley and belt mechanism. Replace if cracked or broken from wear. Confirm fit with your model number.

Secures panels and components in place. Replace this fastener if stripped, corroded, or missing to restore proper alignment and eliminate rattling.

The Capacitor is an OEM part for Whirlpool washing machines. This part helps regulate power supply and voltage levels. It smooths out voltage fluctuations to ensure consistent operation of the motor and internal components.

Causes of a bad capacitor can include faulty wiring connections, or simply wear and tear over time. Capacitors have a limited lifespan based on usage and wear.

Symptoms of a bad capacitor include:

• The washer failing to start or not completing cycles
• Unusual noises coming from the motor area
• Fluctuating water levels and inconsistent filling
• Lights dimming when the washer is running

This genuine Whirlpool OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Screw: 8-16 x 3/8 inch.

Fix a washer stuck in sensing mode or won't spin with a new shift actuator. Controls cycle transitions between agitation and spinning modes.

This genuine replacement screw secures components in compatible Whirlpool appliances, restoring proper fit and preventing rattles or loose panels. Use it when original fasteners are missing, stripped, or damaged. What it does:

• Fastens panels, brackets or small components to maintain structural stability
• Replaces missing or worn screws that cause vibration, rattling, or loose parts
• Restores secure connections after repairs or part replacements
• Helps prevent further damage by keeping parts properly aligned

• Turn off and unplug the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and hand-start the screw to prevent cross-threading
• Keep small parts away from children and pets during installation

Fix a washer that won't drain or shows long drain errors with this water pump replacement. Drains water from the tub during wash cycles. DIY-friendly repair.

Factory fastener that secures panels and components in your laundry center. Replace if missing, stripped, or corroded to maintain proper alignment.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Internal drain hose routes water from the washer tub to the external drain. Replace if cracked, leaking, or damaged from constant use or obstructions.

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.