Generator Valve & Float

A fuel valve shut-off is an important piece that impacts the flow of fuel to the engine. It is designed specifically to be compatible with portable generators by the Generac brand.The fuel valve shut-off part is crucial because it manipulates the flow of oil. The purpose of the fuel valve shut-off is to attach to the fuel tank, and then it either allows fuel to pass to the engine, or it prevents the flow of fuel if the level is too low or if there is another problem. The replacement or repair process of the fuel valve shut-off should be straightforward, but the user replacing the part should always be sure to wear gloves during any assembly, replacement, or installation processes. The user should also refer to the owner's manual of their equipment and any guiding diagrams that clarify the placement location.This fuel valve shut-off is made out of metal and plastic. This fuel valve shut-off is an original OEM part sourced directly from the manufacturer, Generac. It is sold individually.

This replacement part is roll over valve intended for use in generators. This is a genuine replacement part made by Generac. This part is responsible for burning off fumes created by the generator.A new roll over valve might be needed if the current one is damaged or broken in any way. It is not unusual for this part to require replacement after years of normal use. Be sure the appliance is completely powered down and cooled off before attempting to replace this part. For more detailed instructions on how to replace this specific part, please reference the user guide or manual for the appliance. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with generators made by Generac.

This roll over slant valve is an authentic OEM replacement part sourced directly from the manufacturer designed specifically for Generac portable generators. This valve attaches the hose to the fuel tank to allow fuel to be delivered to the engine during operation. If the valve is damaged or cracked, it should be removed and replaced immediately as this could be a safety hazard. When adding fuel to the generator, if leaks are noticed or the fuel is no getting through the valve to the engine, the slant valve should be inspected and replaced.Remove the spark plug from the generator and siphon the fuel out of the tank before replacing the valve. Disconnect the hose from the valve. Open the fuel tank and remove the valve and grommet. Separate the valve from the grommet and attach the new valve. Reinsert the valve and grommet in the gas tank. Attach the hose and fill the tank with gas. Inspect for leaks.This part is made of high-quality black plastic and is sold individually. It is manufactured specifically for Generac generators.

This is a genuine OEM replacement fuel shutoff valve found on portable Generac generators. It is found on the bottom of the fuel tank and is designed to regulate the amount of fuel going into the fuel lines. If the fuel shutoff valve is damaged or if fuel is leaking, the valve should be replaced. Fuel tank repairs should be done in a well-ventilated area. Before attempting to replace the valve, drain the fuel from the tank into a clean receptacle. Remove the bolts holding the fuel tank and remove the tank. Turn the fuel tank over to access the shutoff valve. Loosen the hose clamp to get the fuel hose off. Next, unscrew the tightening nut to remove the old valve. Install the new valve and tighten the nut. Reattach the fuel hoses and clamps. Reinstall the tank to generator. Refill the fuel tank. Check the new valve for leaks before using it. A wrench set and pliers are needed to complete this repair. The replacement can be made in less than half an hour.This is a heavy-duty metal part that is sold as an individual unit. It is made explicitly for portable generators manufactured by Generac.

This plastic body fuel shutoff valve is a genuine OEM replacement part for portable Generac generators. It is an inline fuel valve that is responsible for controlling the flow of gas from the tank to the engine. It is also responsible for stopping fuel from reaching the engine if the generator is not in use. If the fuel shutoff valve is damaged due to normal wear and tear or leaking when not in use, it should be removed and replaced.Repairs involving fuel should be made in an area with adequate ventilation. All fuel should be drained from the fuel tank and fuel lines before removing the valve. Pliers, a screwdriver, gloves, and a basin or tub to drain the fuel are necessary for making the repair. Locate the clamps holding the fuel line on each side and use pliers to release them. Remove the old valve and insert new valve. Replace the fuel lines and reclamp. Refill the fuel and check for leaks.This fuel shut off valve is made of heavy-duty molded plastic and sold as an individual unit. It is made specifically for portable generators manufactured by Generac.