Need Help?
Call
The Dryer Front Bearing Drum Slide (Green, 2-Pack) is an OEM replacement part for GE dryers. These slides are located on the front panel of the dryer and work to support the drum as it rotates. The green slides are designed to reduce friction between the drum and the panel, ensuring smooth operation and helping to prolong the life of the appliance.
Over time, these slides can wear out due to constant movement, heat, and friction. When worn or damaged, the drum may not rotate as intended, leading to noise and reduced efficiency.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
We cleaned out all ducts carefully and did other basic troubleshooting but it did not help. Began to research the problem on-line and discovered that this dryer has two heating elements. One can fail while the other continues to provide heat - but with a large impact on drying time. Watched youtube videos and how to take apart the dryer to reach the heating coils. Tested the heating elements for continuity with tester and the outer loop had no continuity indicating it was broken somewhere. ... Read more
Supports the front of your dryer drum for smooth, quiet rotation. Replace if you hear squeaking or grinding noises. Confirm fit with your model number.
I followed the directions I found on YouTube for removing the front of the dryer. It was fairly easy, with two screws to remove the top and another two to remove the front. Just use a hand Phillips screwdriver, you will have difficulty using a typical power screwdriver due to space limitations. Watch the tabs on the top that engage with the control panel. Push the top to the left to disengage. I broke one of the three. One connector and two fastons needed to be disconnected on the front. ... Read more
Rear drum bearing kit supports and smoothly rotates your dryer drum. Replace when you hear squealing, screeching, or grinding noises. Verify fit with your model.
Repair went well, replaced the pulley wheel, belt, rear drum bearing. Had an issue after replacement with the dryer stopping after ~5mins or so when running with heat. Fluff cycle would run fine. Details: The lock nut on the pulley wheel didn't feel tight enough so i tried to crimp it back on the pulley arm. It then became way too lose. I had to replace it with a plastic washer I had in my toolkit. That fit snug and seems to work fine. I also added some grease to the pulley shaft under... Read more
Dryer bearing slides enable smooth drum rotation. Replace when hearing squeaking or rumbling sounds during cycles. Confirm fit with your model number.
A thumping sound (like sneakers in the dryer) started happening. We stopped using it so that it wouldn't get worse and potentially break more parts. Online research suggested rear drive shaft would be the problem. But also suggested while we have the dryer apart, would be smart to replace the belt and the slides/glides (green and white plastic tabs in front, attached to the door). We ordered all the parts from AppliancePartsPros.com and they arrived FAST. It helps to have two people for this... Read more
The Dryer Bearing Slide (2-Pack) is an OEM replacement part for GE dryers. These slides are installed on the front panel of the dryer and support the drum as it rotates. They help reduce friction and wear, ensuring smooth and quiet operation during drying cycles. This pack includes two bearing slides, which are commonly used together in the dryer assembly.
Over time, bearing slides can wear down due to regular use, heat, and friction. When they become worn or damaged, the drum may no longer rotate smoothly, which can affect the dryer's performance and increase noise levels.
Supports the inner tub for smooth rotation during wash and spin cycles. Replace if you hear loud grinding noise or see oil stains. Verify fit by model.
After researching the problem on this site, I realized that the most likely cause was a bad bearing contained in the shaft & tube assembly. Essentially, the tub seal failed & allowed water to travel down the shaft & into the housing containing the bearing. I confirmed this by pulling the front cover off of the unit & noticed some brown water pooled directly under the shaft & tube assembly. I followed the disassembly instructions on this site & it wasn't too bad but did take some time as pretty... Read more
Supports the rear dryer drum for smooth, quiet rotation. Replace if you hear squeaking, screeching, or thumping during cycles. Verify fit with your model.
First symptoms were squeaking drum. This is probably when new glide strips might have been all that we needed. But I put off fixing it... and I put it off some more. Noises got louder, squeaking became screeching, then it started to vibrate loudly. The front drum bearing (really just a plastic arch that the drum rides on) had broken, and with the drum in a canted position, the rear bearing sleeve got messed up too. I ordered the front drum support bearing, and also a rear drum bearing... Read more
Secures the front rim of your dryer drum and prevents wobble during tumbling. Replace if you hear squeaking, grinding, or notice drum movement.
Replaced upper drum slide assembly, GE dryer Read more
Supports dryer drum weight and enables smooth rotation. Replace if drum wobbles, makes noise, or clothes snag on the top. Confirm fit with your model number.
Took it apart and replaced with new parts. Read more
Bearing only, to get complete assembly order WE25M40
My GE dryer from the late 80's/early 90's was squealing when it would start up, belt or bearing I was thinking. I found a manual online that covered my model and I watched a video on this site that showed me how to take it all apart, mine was a bit different but the principles were the same. I took it apart and added some quick-disconnects to 2 wires so next time I can take the front panel off easily. When I got to the bearing it looked worn but not bad so I cleaned it and put it back. ... Read more
Supports the front of the dryer drum for smooth rotation. Replace if drum wobbles, makes noise, or clothes have black marks. Verify fit with your model.
Parts came super quick (2 days to Hawaii). I replaced the drum support shaft bearing, the front drum support and the slides on my GE electric dryer. I used the step by step video provided. The electrical panel on the top was different than the video but as suggested I took detailed pictures of it before I disconnected 20 or so individual wires to the control board. I couldn't take the entire top plate off the dryer because some of the wires were shared and spliced together from either side.... Read more
Usually ships within 4 - 14 days
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.