Hotpoint Axle, Roller, Pulley Parts
Genuine Ge part
By: Ge
Part Number: WE12X83
The Idler Pulley is an OEM part for GE dryers. This critical component helps to maintain the correct tension on the dryer's drive belt, ensuring smooth operation and preventing it from slipping.
Symptoms of a bad Idler Pulley include:
- Squeaking or screeching noises during dryer operation, often a sign of bearing wear or failure.
- The dryer drum not turning smoothly, or at all, indicating that the belt may be slipping or has come off entirely due to a failed pulley.
- Excessive heat or a burning smell, which can occur if the pulley is seizing up and causing friction.
- Visible wear or damage to the pulley itself.
Causes of a bad idler pulley can include worn bearings, accumulation of lint and debris that impedes rotation, or material fatigue after prolonged use.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Very loud squeal noise Thomas P. • Dundalk , MD • June 05, 2018
Repair went well, replaced the pulley wheel, belt, rear drum bearing. Had an issue after replacement with the dryer stopping after ~5mins or so when running with heat. Fluff cycle would run fine.
Details:
The lock nut on the pulley wheel didn't feel tight enough so i tried to crimp it back on the pulley arm. It then became way too lose. I had to replace it with a plastic washer I had in my toolkit. That fit snug and seems to work fine. I also added some grease to the pulley shaft under...
Read more
More
$24.95
- Compare At:
-
$30.92
- You Save:
-
$5.97
Genuine Ge part
By: Ge
Part Number: WD35X21038
Replacement roller and axle kit for dishwasher lower racks. Includes 8 wheels and 8 axles. Replace when rollers are broken, cracked, or missing.
Do-It-Yourself Stories from Customers like You
Dishwasher lower rack wheels were melted/broken and the rack wouldn't roll the washer would make a loud clunking noise while aggitating one of the rubber top tub restraints were broken Joseph Z. • Louisville , KY • September 23, 2016
I never respond to these kinds of requests but I must respond to this one because of your superior service!
The best story here was that I ordered the parts from AppliancePartsPros at 4:15 p.m. one day, and they were on my porch by 2:00 p.m. the next day!! I am very impressed, so please keep up the great work. I'll add that the prices were the best I found too.
The dishwasher wheels replacement didn't require tools & took less than 15 minutes.
The original design/materials are not very...
Read more
More
$40.59
- Compare At:
-
$48.71
- You Save:
-
$8.12
Genuine Ge part
By: Ge
Part Number: WD12X26146
The Lower Rack Roller is an OEM replacement part for GE dishwashers. This small but crucial component allows for smooth and effortless movement of the lower dish rack during loading and unloading.
Symptoms of needing to replace the lower rack roller include:
- Difficulty in sliding the lower rack in or out
- Excessive noise or grinding during rack movement
- The rack becoming stuck or not rolling smoothly
- Visible wear, cracks, or damage to the roller itself
Causes of a faulty lower rack roller can include normal wear and tear over time, exposure to heat or moisture, or physical damage due to impact or mishandling.
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore dishwasher models.
Do-It-Yourself Stories from Customers like You
A wheel housing attached to the bottom of the dishwasher dish rack had come off and melted in a wash cycle Jessica B. • Dayton , NV • November 03, 2024
I was able to find the parts on your website. I was a little worried because there were no photos, but the parts were correct, and it was an easy fix!
Read more
More
$10.39
- Compare At:
-
$12.26
- You Save:
-
$1.87
Genuine Ge part
By: Ge
Part Number: WD12X10327
Replacement roller and stud assembly for dishwasher racks. Installs on upper or lower rack to restore smooth gliding. Needed when rollers crack or studs break.
Do-It-Yourself Stories from Customers like You
Clips on top rack of washer were worn out. Top rack would fall off..down Tamara K. • Richmond , MI • April 06, 2014
Ordered the clips that we easy to find on line.
They can within a few days..and replaced them myself..didn't wait for my husband. Hardest part was getting the end caps off the metal rack to replace the rollers and clips. They fit in there spmehow. I used a screwdriver to get them out. Rest was a piece of cake
Lol
Read more
More
$23.95
- Compare At:
-
$28.74
- You Save:
-
$4.79
Genuine Ge part
By: Ge
Part Number: WH03X32097
Transmission pulley and nut for top-load washers. Transfers motor power to the drum for spinning and agitation. Replace if cracked, worn, or damaged.
Do-It-Yourself Stories from Customers like You
The washer would not spin. Clayton B. • Calhoun , LA • October 13, 2023
Replaced thr motor pulley and transmission pulliey and belt.
Read more
More
$31.95
- Compare At:
-
$38.02
- You Save:
-
$6.07
Genuine Ge part
By: Ge
Part Number: WE03X31620
Idler pulley for dryer drum assembly. Maintains belt tension to enable smooth drum rotation. Replace if worn, cracked, or causing noise during operation.
Do-It-Yourself Stories from Customers like You
Drum would not rotate intermittently. Robert L. • Cary , NC • May 24, 2019
The Dryer is 10 years old GE Front Load DPVH890JEMG. The drum would intermittently not rotate at the beginning of a cycle and occasionally would rotate but then start and stop throughout the cycle. I did not check error codes, but the windings on the motor were black. So it seemed reasonable that the motor was overheating and sending a signal to the control board to stop. There is one screw under the knob and 9 screws on the front to get inside. I decided to replace the bearings, capacitor,...
Read more
More
$33.95
- Compare At:
-
$40.40
- You Save:
-
$6.45
Genuine Ge part
By: Ge
Part Number: WH03X32218
Motor pulley with nut for top-load washers. Transfers power from motor to drum. Replace if pulley teeth are stripped, cracked, or sheared off.
Do-It-Yourself Stories from Customers like You
The washer would not spin. Clayton B. • Calhoun , LA • October 13, 2023
Replaced thr motor pulley and transmission pulliey and belt.
Read more
More
$24.58
- Compare At:
-
$29.25
- You Save:
-
$4.67
Genuine Ge part
By: Ge
Part Number: WD35X20994
Upper dishrack roller kit with 4 nylon rollers and 4 axles. Replace broken, cracked, or worn rollers that prevent smooth rack gliding in your dishwasher.
Do-It-Yourself Stories from Customers like You
Water was leaking from base water was not draining from tub extreme build up of mineral deposits Kateri G. • Vista , CA • September 18, 2016
Removed and cleaned all inside components of dishwasher. Replaced the sump inlet and fine filter. I decided to complete the repair myself when my appliance repairman did not want to help me. The videos from Appliance Parts Pro are AMAZING!!!! Gave me the confidence to do the repair myself (had to fully uninstall the machine and flip it over). THANK YOU!!!
Read more
More
$41.95
- Compare At:
-
$49.92
- You Save:
-
$7.97
Genuine Ge part
By: Ge
Part Number: WD12X271
Replace broken or missing lower dishrack rollers and axles. Attaches to the bottom rack for smooth gliding when loading dishes. Sold as one roller kit.
Do-It-Yourself Stories from Customers like You
Bottom dishwasher rack needed new wheels Thomas C. • Alton , IL • December 19, 2014
I found my parts and ordered the six I needed, however I did not pick up on the difference from the front wheels to the rear wheels in the the descriptions. The rear wheels are narrower and I ordered all front wheels, six fronts instead of four front and two rear. I made it work by using the axle from the new wheel with two old narrow wheels.
Read more
More
$20.95
- Compare At:
-
$24.72
- You Save:
-
$3.77
Genuine Ge part
By: Ge
Part Number: WD12X27578
Replacement roller for dishwasher racks. Installs on the rack guide rails to allow smooth gliding in and out. Needed when rollers are cracked or worn.
More
$11.59
- Compare At:
-
$13.91
- You Save:
-
$2.32
Genuine Ge part
By: Ge
Part Number: WE12X81
Maintains belt tension for smooth drum rotation. Replace if the pulley is cracked, worn, or the nylon bushing is broken to restore proper operation.
Do-It-Yourself Stories from Customers like You
The dryer was squeaking loudly George V. • Weirton , WV • December 13, 2014
I replaced the drum bearing in the back and also the nylon sliders in the front. It rook some time but was not difficult. I took some extra time to thoroughly clean all the lint from the inside.
Read more
More
$21.64
- Compare At:
-
$29.75
- You Save:
-
$8.11
Genuine Ge part
By: Ge
Part Number: WH07X10019
Drive pulley mounts to the washer basket shaft and routes the belt from the motor. Replace if worn, cracked, loose, or showing play on the shaft.
Do-It-Yourself Stories from Customers like You
Clunking and grinding from the drive Scott R. • Onondaga , MI • August 14, 2015
Replaced the shaft & mode shifter assembly. Also replaced the pulley as it had taken some damage from the wobbling clutch dog. And replaced the tub seal since it's normally inaccessible with the shaft in place. This is an advanced repair that took a lot of time. Removing the tub nut took a 1 11/16" socket and a 700 ft-lb impact wrench and I had to hammer on the nut for several minutes to break it free of the tub. Disassembly of the washer is complete, and requires a lot of space for...
Read more
More
$47.59
- Compare At:
-
$56.63
- You Save:
-
$9.04
Genuine Ge part
By: Ge
Part Number: WD12X10278
White dishwasher lower rack roller axle. Replaces broken or worn axles that cause wheels to fall off. Snap-in design for easy installation.
Do-It-Yourself Stories from Customers like You
Dishwasher rollers had worn down and some were melted since they fell off into the heating element so the lower shelf door was constantly off its track Kara O. • Cincinnati , OH • February 15, 2015
We purchased both the roller studs and new rollers for all of the slots on the lower rack. They came two days later and I was able to easily click them into place and the lower rack now rolls smoothly and securely. I only wish I hadn't lived with it in the broken stage as long as I did - such an easy and affordable fix.
Read more
More
$9.24
- Compare At:
-
$10.16
- You Save:
-
$0.92
Genuine Ge part
By: Ge
Part Number: WD12X332
Includes screws.
Do-It-Yourself Stories from Customers like You
Top rack on the dishwasher wouldn't stay attached. Sean E. • Bakersfield , CA • March 15, 2021
Replaced the upper rollers and the rack rollers along with new caps for the slide bars. Everything fit perfectly and it fixed the problem. A bit pricey but cheaper than a new dishwasher plus installation
Read more
More
$12.01
- Compare At:
-
$14.10
- You Save:
-
$2.09
Genuine Ge part
By: Ge
Part Number: WE03X20434
Supports the idler pulley to maintain proper belt tension in your dryer. Replace if the arm is warped, cracked, or causing belt tracking issues.
Do-It-Yourself Stories from Customers like You
Dryer won’t tumble belts keep breaking. Devon Ann B. • Melbourne , FL • March 27, 2021
After replacing the belt less than a year ago, when it broke again we started to think something may be going on with the idler pulley. Ordered a new belt and pulley wheel, only to have the belt break again the very next day. After a call to customer service explaining the situation, they replaced the belt and pulley wheel which were both under warranty, and suggested replacing the arm itself. We also had to replace the interlock switch. Parts arrived quickly. The repair itself took about an...
Read more
More
$85.36
- Compare At:
-
$101.58
- You Save:
-
$16.22