Hotpoint Dryer Parts

If your dryer won't heat or takes too long to dry, a faulty gas igniter is often the cause. This assembly heats up to ignite the burner for proper drying.

Maintains belt tension for smooth drum rotation. Replace if the pulley is cracked, worn, or the nylon bushing is broken to restore proper operation.

The Blower Wheel is an OEM component specifically designed for GE dryers. It is responsible for circulating air during the drying cycle, directing airflow through lint and clothes to remove moisture. The plastic blades of the blower wheel push air through the dryer and out the vent when the motor is running. 

Symptoms of a bad blower wheel include:

• Slow or inefficient drying times even on low moisture loads    
• Strange noises from inside the dryer cabinet      
• Excessive vibrations felt through the dryer door or cabinet
• Bent or cracked blower wheel blades

Causes can include normal wear and tear over time, accidents that damage the blades, or failures in the secure mounting of the blower wheel.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

Dryer not heating? This heating element assembly restores heat when coils burn out. Straightforward DIY repair with basic tools in 1-2 hours.

Replacement drum baffle installs inside your dryer to lift and tumble clothes during drying. Replace if cracked, broken, or mounting holes are stripped out.

This CCMR 30-amp, 120-volt fuse protects the appliance's electrical circuit by opening when current exceeds safe limits. Replace a blown fuse to restore power to the affected circuit and help prevent damage to internal components.

• Provides overcurrent protection for the circuit specified by the manufacturer
• If the fuse is open, the appliance may be dead, won't start, or certain functions won't operate
• Helps prevent wiring and component damage from shorts or overloads
• Repeated fuse failures indicate an underlying electrical issue requiring diagnosis

• Disconnect power to the appliance before servicing
• Locate the fuse in its holder/block and inspect associated wiring for heat or damage
• Test the old fuse for continuity; replace only with the identical rating specified
• Never bypass or upsize a fuse; correct the root cause of the failure before returning to service

Dryer barely blowing air or taking forever to dry? A worn blower wheel fails to pull air through the drum. This wheel restores airflow for efficient drying.

This valve and pipe assembly regulates and routes fuel through the dryer's system so the burner can ignite and maintain heat. Replacing a failing assembly restores reliable heating performance and consistent drying results. What it does

• Opens and closes to control fuel flow to the burner when heat is called for
• Directs fuel from the inlet to the burner orifice through a rigid manifold/pipe
• Helps maintain safe shutoff when the dryer is idle
• Common symptoms of a failing assembly: no heat, intermittent heat, or burner failing to ignite

• One valve-and-pipe assembly

• Disconnect power and shut off the gas supply before servicing
• Use only gas-rated fittings/sealant as specified by the manufacturer; do not overtighten connections
• After installation, check all joints for leaks with a soap-and-water solution
• Restore power and gas, then verify proper burner ignition and stable heating

Converting your dryer from LP propane to natural gas? This conversion kit includes the orifice and components needed for a quick, straightforward swap.

Reversible door plug fills unused mounting holes when switching refrigerator door swing direction. Replaces broken or missing plugs for a finished look.

Dryer won't heat or you smell gas? The gas valve controls fuel delivery to the burner. Common fix for heating failures and gas leaks. Moderate DIY repair.

Supplies electrical power from wall outlet to refrigerator. Replace this cord if cut, frayed, overheated, or damaged to restore safe electrical connection.

This fuse terminal cover shields and insulates the fuse connection inside your appliance, helping prevent accidental contact and shorting. Replace a cracked or missing cover to maintain safe electrical protection and dependable circuit performance.

• Covers and insulates the fuse terminals to protect the connection
• Helps prevent accidental contact, arcing, and debris intrusion at the fuse
• Common signs you need this part: missing cover, cracks, heat discoloration, or a cover that won't stay secured
• Promotes a secure, consistent fuse connection once installed

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the fuse area per your service information; note wiring and cover orientation
• Remove the damaged cover; inspect terminals and wiring for heat damage or looseness
• Seat the new cover fully and verify it is secure and clear of wiring

Supports the idler pulley to maintain proper belt tension in your dryer. Replace if the arm is warped, cracked, or causing belt tracking issues.

Protective cover that shields the rear power connection terminals on your dryer. Replace if cracked, broken, or missing to prevent lint buildup and accidental contact with electrical connections.

Fixes dryer not heating or overheating issues. This safety thermostat monitors temperature and cuts power when too hot. Basic DIY repair, 30 minutes.