Husqvarna String Trimmer Parts

Engine piston kit for gas trimmers and outdoor equipment. Replaces worn, damaged, or corroded pistons that cause poor compression and engine performance.

Flanged hex nut for lawn tractors and outdoor power equipment. Replace if threads are stripped, nut is missing, or hardware has corroded or loosened.

Deck spindle assembly for riding mowers and lawn tractors. Mounts under the mower deck to hold and spin cutting blades. Replace if cracked, bent, or worn.

Ignition module for chainsaw engines. Installs on the engine block to control spark timing. Replace if cracked, damaged, or corroded terminals affect ignition.

Fuel pickup filter draws gas from tank to carburetor. Replace if engine won't start or runs poorly due to clogged filter. Verify fit with your model number.

This is a replacement carburetor for Husqvarna string trimmers and is also used on some Craftsman models. It consists of an aluminum body with a bright blue choke and cherry red primer bulb. Engines rely on a mixture of fuel and air for proper operation. In a small engine, the fuel and air mix inside the carburetor. This is achieved with a series of small channels, which release a fine mist of fuel into a vortex of air. When one of these channels gets clogged, it can negatively impact engine performance. Carburetors can often be cleaned with a commercial carburetor cleaning spray, but this is sometimes not sufficient to clean a badly clogged carburetor. In this case, other measures such as hypersonic cleaners can often be effective, but they’re not always worth the cost. The alternative is replacing the entire carburetor, which can be done using this kit. This is an OEM part sourced directly from the manufacturer, and it is sold individually. A heat shield is also included with the kit.

Blocks dirt and debris from entering your trimmer engine. Replace when clogged or worn to restore proper airflow and prevent rough running or starting issues.

If your chainsaw rope won't retract after pulling, the starter spring likely needs replacement. This spring creates the recoil to start the engine.

Replacement fuel tank for front-engine lawn tractors and riding mowers. Installs to store fuel. Replace if cracked, damaged, or leaking.

This is a genuine OEM replacement drive V-belt for a riding lawn mower. The drive V-belt attaches to the drive pulley and transfers rotational motion from the transmission to the mower blade. This causes the blade to then spin and cut grass. By using a belt to transfer motion, the engine does not have to work as hard to spin multiple parts, meaning that it runs more efficiently. Drive V-belts are made of a rubber composite material that will begin to fray and stretch over time. Due to continuous motion, these belts absorb a lot of wear and tear, and if left for too long, they can eventually snap and leave the mower blade non-functional. Therefore, it is wise to check the condition of a V-belt during regular maintenance. As soon as it appears to be wearing away, replace it with a new part using a nut driver and screwdriver. When detaching the lower deck, be sure not to lose the bolt clips, as they are required for reassembly. As a high-quality replacement part, this drive V-belt is directly sourced from its original manufacturer. It is compatible with riding lawn mowers made by Husqvarna, Poulan, Craftsman, and Jonsered. This part ships individually.

Shoulder bolt that attaches the suspension arm to the wheel bracket on riding mowers and tractors. Replace if bolt is stripped, worn, or missing.

Replacement muffler for front-engine lawn tractors. Installs on the engine exhaust system. Replace if cracked, rusted, or leaking exhaust gases.

This mow ball assembly is used in many Husqvarna string trimmers to offer a height guide that prevents the trimmers from cutting grass or other foliage too low. This is an entire assembly that includes the ball bearing, plastic housing, and retaining ring needed to replace the mow ball. The bolt that is used to attach the part to the string trimmers is available separately. If the mow ball assembly is broken or damaged, the guide for the blade will not function and the trimmer may cut the grass too close to the ground. The first step to replace this part is unbolting the assembly using the bottom bolt located on the shaft of the cutter. Clean all the parts before greasing the adjustment button to make it easy to move. Take off the mow ball assembly and replace it with a new one.This part is sold as an individual unit. It is an authentic OEM replacement part that is directly sourced from the manufacturer. The mow ball assembly is compatible with string trimmers manufactured by Husqvarna.

Secures the mower blade to the spindle on riding mowers and tractors. Replace if bolt is stripped, washer is damaged, or hardware is missing.

Replacement piston and cylinder kit for string trimmers. Restores engine seal and compression. Needed when original is worn, scored, or damaged.

This is a genuine replacement wheel for select push mowers. The wheels assist with maneuvering the Lawn Mower and keeping the mower deck from coming in contact with the ground. On select models, the wheels are what offer a cutting height adjustment so that the grass can be cut to the appropriate length. Wheels can be damaged or become worn with regular use, necessitating a replacement. This wheel can provide the appropriate manufacturer part for compatible machines. Those who need to replace multiple wheels will have to order this part in multiple quantities. This genuine OEM replacement wheel is designed to be compatible with select lawn equipment from Husqvarna and Weed Eater. The wheel is made of durable composite plastic and sold as an individual piece. The washer and axle bolt required to secure the wheel will need to be purchased separately. This part can be replaced with a wrench and should only take a few minutes to repair. Always wear gloves when working on lawn equipment.