Parts for Jenn-Air JSD2989AEW: 10 - Ice Bin (Rev 11) Parts

The Whirlpool EveryDrop Refrigerator Water Filter 7 features a coconut carbon filter that reduces contaminants to provide clean, fresh tasting water. This filter is used Whirlpool side-by-side refrigerators which accept Filter 7. Single filter. Simple, quick turn installation requires no special tools. For best performance, replace every six months. Certified to fit these leading refrigerator brands: Maytag and Jenn-Air. Micron Rating: 0.5. Filter Media: Coconut Carbon Block. Flow Rate: 0.5 GPM. Temp Range: 33 - 100 °F. Pressure Range: 30 - 120 psi. Meets NSF Standard: 42. Approved for WQA Gold Seal. Approximate dimensions: 8.25" x 8.25" x 6.5"

This genuine replacement screw secures appliance panels and trim so covers, consoles, and components stay firmly in place for safe, quiet operation. It replaces worn or missing fasteners to restore proper fit and reduce vibration and rattling. What it does:

• Secures control panels, trim pieces, or access panels to the appliance frame
• Keeps panels aligned to prevent gaps and light leaks
• Reduces vibration-related noise from loose panels or components
• Helps maintain safe operation by keeping covers and guards properly attached

• The replacement screw shown/listed

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start the screw by hand to ensure proper thread engagement, then tighten securely but do not overtighten

This genuine replacement screw secures appliance panels and trim so covers, consoles, and components stay firmly in place for safe, quiet operation. It replaces worn or missing fasteners to restore proper fit and reduce vibration and rattling. What it does:

• Secures control panels, trim pieces, or access panels to the appliance frame
• Keeps panels aligned to prevent gaps and light leaks
• Reduces vibration-related noise from loose panels or components
• Helps maintain safe operation by keeping covers and guards properly attached

• The replacement screw shown/listed

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start the screw by hand to ensure proper thread engagement, then tighten securely but do not overtighten

Flat plain washer that distributes load and spaces hardware on appliance assemblies. Replace if worn, missing, or needed for secure fastening.

Machine screw secures appliance panels, brackets, and internal components. Replace missing, stripped, or worn fasteners for reliable assembly.

Fixes ice dispenser not dispensing or auger not turning. This motor assembly drives the auger shaft that moves ice from bin to chute. Moderate difficulty.

Ice not dispensing? A worn auger drive bar with stripped threads prevents ice from moving through the chute. Moderate DIY repair with video guidance.

Replacement fastening screw for securing trim, panels, and brackets inside appliances. Use when original screw is missing, stripped, or damaged.

Broken ice enclosure causing ice jams or warm air leaks? Replace this ice path housing. Moderately easy DIY repair—remove one screw and wire harness.

Replacement fastening screw for securing trim, panels, and brackets inside appliances. Use when original screw is missing, stripped, or damaged.

This guide yoke is a replacement guide that supports and guides a moving assembly so the appliance part moves smoothly and stays aligned. Replacing a worn guide yoke restores reliable, quiet operation and reduces binding or misalignment. What it does:

• Guides and stabilizes a sliding or pivoting component to maintain proper alignment
• Helps prevent rubbing, binding, or uneven movement of the associated assembly
• Reduces noise caused by worn or damaged guide surfaces
• Restores smooth operation when the original guide is cracked, bent, or excessively worn

• One (1) guide yoke

• Disconnect power (and gas where applicable) before servicing to prevent shock or injury
• Access the mounting location by removing the relevant panel or assembly
• Install new guide in the same orientation; secure fasteners snugly but do not overtighten
• Test the moving assembly for smooth operation before reassembling panels

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

Machine screw secures appliance panels, brackets, and internal components. Replace missing, stripped, or worn fasteners for reliable assembly.