Parts for Lg LRMXC2206S/00: Ice Maker & Ice Bin Parts

The Handle Mounting Stud is an OEM replacement part for LG refrigerator doors. It provides a sturdy mounting point for the door handle assembly. Reliable handle connection and support is crucial for dependable door function and access. 

Causes of a faulty stud can include damage from excess weight or impact over time rendering the stud loose or unstable.

Symptoms of a bad stud include:

• Loose or sagging door handle  
• Difficulty opening and closing the refrigerator door  
• Potential for the handle to detach completely
• Safety concerns if the handle connection fails

This OEM LG replacement stud is also compatible with Sears/Kenmore models. 

The Drain Pipe Assembly is an OEM replacement part for LG refrigerators. It is a plastic tubing system that collects and removes liquid condensation from evaporator coils. Proper drainage is crucial to minimizing frost buildup and ensuring optimal cooling of food storage areas. 

Symptoms of a bad drain pipe assembly include:

• Excessive frost or ice accumulation inside the refrigerator
• Puddling or leaks detected near evaporator housing
• Slow draining allowing water to pool versus emptying fully
• Cracks or breaks in the tubing prevent complete fluid removal

Causes are typically mineral sediment clogging drainage paths or deteriorating plastic from constant use. This OEM LG replacement pipe restores reliable condensate removal to maintain peak efficiency.

This OEM LG part is also compatible with Sears/Kenmore. 

The Leveling Leg is an OEM part for LG refrigerators. It is one of the four legs at the bottom corners that elevate and provide stability to the entire appliance.

Causes of failure can be broken mounting points that no longer provide secure elevation, full compression of the built-in cushioning, or damage from impact on an unlevel floor.

Symptoms of a faulty leveling leg include:

• Excessive shaking or vibrating of the refrigerator
• Door alignment issues where doors are difficult to open or close fully
• Visible leaning or misalignment of the refrigerator cabinet

This OEM LG part is also compatible with some Kenmore models.

This drawer tray assembly replaces a damaged tray so the drawer aligns and slides correctly again. It restores safe support for stored items and keeps your refrigerator organized and easy to use.

• Supports and contains items within the drawer area
• Provides the structure/glide surface for smooth opening and closing
• Helps the drawer sit level and close fully for proper sealing and airflow
• Common symptoms: cracks, broken tabs, warping, sticking or misaligned drawer, drawer coming off track

• Disconnect power and remove contents from the affected section
• Pull the drawer straight out; remove any shelves that obstruct access
• Align the new tray with the tracks/tabs and seat it fully until engaged
• Wear gloves and handle plastic carefully to avoid damage

This right-side refrigerator shelf assembly replaces a damaged or missing shelf to restore safe, level storage and keep foods organized. Tough construction supports deli containers, leftovers and other everyday items. What it does

• Provides a flat, stable storage surface on the refrigerator's right side
• Replaces cracked, chipped or broken shelves that allow items to tip or fall
• Restores original spacing so doors and drawers close and seal properly
• Helps maintain organized storage to prevent spills and contamination

• One right-side refrigerator shelf assembly

• Unplug or power off the appliance before removing or installing parts
• Remove food and clean the area; lift shelf straight out of its supports to avoid chipping
• Handle glass or edges carefully; use two people for heavy or awkward shelves

Note: Shelf is on the LEFT side. 

This shelf net is a replacement mesh shelf designed to support lightweight items and produce in your refrigerator while allowing airflow. It restores storage organization and prevents small items from falling through broken or stretched shelving. What it does:

• Replaces torn, stretched, or missing mesh shelving to restore a secure, breathable shelf surface
• Helps keep small containers and produce stable and contained on the shelf
• Maintains airflow across the shelf area to help even cooling
• Fits into existing shelf brackets or frame to replace the original netting

• Unplug or disconnect power and remove food and containers from the shelf area before installing
• Remove the old net by releasing any clips or fasteners, then position the new net into the shelf frame or brackets
• Install by snapping or fastening into place; avoid overstretching the mesh to prevent premature wear

This shelf net is a replacement door shelf retainer that helps keep small, loose items secure and visible in the refrigerator door. It restores the original storage barrier so bottles, cans, and jars stay in place. What it does:

• Replaces a cracked, stretched, or missing door shelf net that no longer holds items securely
• Prevents small containers and packages from shifting or falling when the door opens
• Restores original appearance and storage function of the door shelf area
• Fits into the existing shelf frame and secures items without blocking visibility

• One shelf net

• Remove all items from the affected door shelf before installing
• Install by snapping or sliding the net into the existing shelf frame per the OEM layout
• No electrical disconnection required, but handle shelves and trim carefully to avoid breakage

This TV cover assembly replaces the outer cabinet panel that protects internal electronics and restores the television's appearance and structural support. Use it to repair cracked, broken, loose or missing covers and to reduce rattling or exposed components. What it does:

• Protects internal circuit boards, connectors and speakers from dust and damage
• Replaces cracked or damaged cabinet panels that cause cosmetic issues or expose components
• Stops loose or rattling panels that can create noise during operation
• Restores mounting points and alignment for screws and internal assemblies

• Always unplug the TV and allow time for internal capacitors to discharge before starting work
• Handle the assembly carefully to avoid scratches; use appropriate screwdrivers for mounting hardware
• Keep track of screws and small parts during removal; replace any damaged fasteners

This tray assembly fits the refrigerator fresh room to support the crisper/drawer area and help contain spills. Replacing a cracked or warped tray restores smooth drawer movement and helps keep produce organized. What it does:

• Provides a stable support surface for the fresh room/crisper drawer.
• Helps contain drips and small spills to prevent messes in lower compartments.
• Restores even drawer sliding and reduces binding, rattling, or misalignment caused by a damaged tray.
• Fits specific fresh room assemblies.

• Unplug the refrigerator or switch off power before servicing to avoid electrical hazard.
• Remove the fresh room/crisper drawer to access the tray; the tray typically lifts or slides out.
• Retain any clips or fasteners and reinstall them with the new tray as needed.

This cover tray is the molded plastic top/cover that protects and contains the unit's internal tray area, helping keep components clean and guiding condensate or collected material into the tray. Replaces cracked, warped or missing tray covers to restore proper containment and appearance. What it does

• Covers and protects the appliance's internal tray area to prevent debris from entering internal components.
• Guides liquid or collected material into the tray for proper containment.
• Helps maintain correct fit and alignment of adjacent panels and parts.
• Common symptom: visible cracks, warping, loose fit or missing cover causing spills or debris entry.

• Disconnect power and remove any water or debris from the tray area before replacing the cover.
• Inspect surrounding tabs and mounting points for damage; replace any broken fasteners for a secure fit.
• Handle the plastic cover carefully to avoid cracking; hand-tighten any screws to avoid stripping.

This Tray Cover Assembly replaces a damaged or missing tray cover to restore a finished appearance and proper protection for the underlying tray area. Designed to fit and align with the original mounting points for a secure fit. What it does:

• Covers and protects the appliance tray from spills, debris, and everyday wear
• Helps maintain correct spacing and alignment of tray components
• Restores the original look where the tray cover is cracked, warped, or broken
• Stops light drafts or minor leaks by resealing the tray perimeter (when part is intact)

• One tray cover assembly

• Install with appliance powered off and water/ice supply turned off if working near dispenser or ice components
• Align tabs and mounting points, then press or fasten according to original hardware—do not force parts into place
• Inspect surrounding clips and screws; replace damaged fasteners to ensure a secure fit

The Deli Drawer Front Cover is an OEM part for LG refrigerators. It provides an attractive facia that protects the internal components of the deli drawer. This cover is designed to integrate with the style and finish of the refrigerator interior. 

Symptoms of a bad Deli Drawer Front Cover include: 

• Cracks, chips, or other visible cosmetic damage
• Discoloration that detracts from the aesthetics  
• The cover is loose, misaligned, or missing
• Difficulty opening or closing the deli drawer

Causes of a bad cover can be normal wear and tear over time from repeated use, as well as accidental drops or impacts that cause cracks or breaks.

This OEM replacement part is also compatible with select LG models.

The Refrigerator Air Filter Cover is an OEM replacement part for LG refrigerators. It provides a protective casing for the refrigerator's air filter. The air filter cover makes filter replacement easy while allowing uniform airflow distribution for optimal cooling and freshness. 

Causes of a bad air filter cover can include cracks or breaks from normal use over time. Screws or securing mechanisms may also become loose.

Symptoms of a bad air filter cover include:

• Cool air escaping without circulating properly
• Inability to easily access the air filter for replacement  
• Excessive refrigeration coil or evaporator fan noise

This OEM LG part is also compatible with Sears/Kenmore models. 

This Vegetable Tray Assembly replaces a damaged or worn crisper drawer tray to restore a stable storage surface for fruits and vegetables and keep the crisper area organized. Fits where the factory tray sits under the vegetable drawers. What it does:

• Provides a stable shelf for vegetable and fruit bins so drawers slide and store correctly
• Supports crisper drawers and prevents sagging or cracking from everyday use
• Helps maintain proper drawer alignment to reduce rubbing or binding when opening/closing
• Addresses symptoms like a cracked or warped tray, unsecured drawer, or uneven drawer movement

• Disconnect power to the refrigerator before working on internal components
• Remove crisper drawers and any contents; lift out the old tray and set the new tray into the same position
• Handle plastic parts carefully to avoid cracking; do not force parts into place—ensure proper alignment with tracks
• Reuse only the screws/clips that match the OEM locations; replace damaged fasteners before returning the appliance to service

This lamp cover is the replacement light lens that protects and diffuses the appliance's internal lamp, restoring even illumination and shielding the bulb from moisture and debris. It's a direct-fit exterior lens for the lamp assembly. What it does:

• Protects the interior lamp from dust, moisture and impact to help prevent bulb damage
• Diffuses and directs light for even illumination inside the compartment
• Restores a cracked, yellowed or missing lens to improve visibility
• Helps maintain the lamp assembly's proper fit and alignment

• One lamp cover / light lens

• Power off and unplug the appliance before beginning any service
• Remove lamp bulb per manufacturer instructions before replacing the cover to avoid damage
• Use proper tools and handle the lens gently to avoid scratching or cracking
• If mounting clips or screws are worn or missing, replace them separately

This Tray Cover Assembly replaces a damaged or missing cover on the appliance tray to help contain contents and keep the tray functioning correctly. It restores the tray's protective surface and helps prevent spills or contamination. What it does:

• Covers and protects the tray surface to keep contents contained
• Helps direct contents into the tray area to reduce spills
• Replaces cracked, warped or broken covers that no longer seat properly
• Restores a flush fit and appearance for the tray area

• One tray cover assembly

• Disconnect power to the appliance before beginning any service
• Remove the tray or access panel per your model's service instructions to access mounting points
• This part typically snaps or slides into place; light tools (screwdriver) may be needed to remove retaining clips

This freezer door foam assembly replaces the insulation layer inside a freezer door to help restore proper temperature control and reduce condensation. It fits into the inner door cavity to improve cold retention and door performance. What it does:

• Replaces deteriorated or waterlogged door insulation that can lead to warm spots
• Helps reduce frost or ice buildup inside the freezer by restoring proper insulation
• Limits condensation and moisture between door panels that can cause odors or corrosion
• Supports overall temperature stability for better freezer efficiency

• One freezer door foam assembly

• Disconnect power before servicing and work on a dry, level surface
• Remove the inner door panel to access the foam; keep fasteners and clips organized
• Insert foam carefully to avoid tearing; align with locating features in the door cavity
• If the door uses adhesive or retention clips, reuse original hardware or OEM-recommended replacements

This freezer door foam assembly replaces the insulating foam inside a freezer door to help restore the door's sealed fit and reduce air leakage. It helps improve temperature stability and reduces frost buildup when the existing foam is damaged. What it does:

• Replaces deteriorated or compressed insulation inside the freezer door
• Restores a tighter door seal to reduce warm air infiltration
• Helps reduce excessive frost or ice buildup caused by air leaks
• Supports consistent freezer temperatures and efficient operation

• Disconnect power before starting and work with the door supported or removed to avoid injury.
• Remove the inner door panel or liner carefully to access the foam; keep fasteners and clips organized.
• Fit the foam into the door cavity without overstretching; ensure even contact with mating surfaces for a proper seal.
• If adhesive, clips, or a door liner are required, replace or reinstall them as needed.

This replacement door gasket creates a heat-resistant seal between the oven door and the front frame. A tight seal helps the oven maintain temperature and cook evenly while keeping heat from escaping into the kitchen.

• Seals the oven cavity to reduce heat loss and temperature fluctuations
• Helps improve preheat times and baking performance
• Worn seals can cause heat leakage, longer cook times, or hot air felt around the door
• Cracks, flattening, or fraying indicate the gasket should be replaced

• Disconnect power before servicing; allow the oven to cool completely
• Open the door and carefully release the old gasket from its mounting clips
• Align and press the new gasket into the channel, seating each clip fully
• After installation, check for even contact around the door

Replacement door gasket that seals the refrigerator door to help keep cold air in and warm air out, reducing frost and cold-air leaks and helping the appliance maintain consistent internal temperatures for food preservation. What it does:

• Creates an airtight seal around the refrigerator door to minimize cold-air loss
• Helps prevent frost buildup in the fresh-food compartment and freezer-adjacent areas
• Addresses symptoms like visible cracks, tears, gaps, or cold air escaping from the door edges
• Helps the fridge maintain set temperatures and can reduce the workload on the cooling system

• Disconnect power to the appliance before starting any repair
• Remove the old gasket fully and clean the door channel to ensure a proper new seal
• Press the new gasket into the channel evenly, working around the perimeter and checking for full contact
• After installation, close the door and inspect the seal; allow a short settling period and re-check for gaps

This hinge cover assembly replaces a damaged or missing hinge trim to protect the hinge mechanism and restore the appliance's finished appearance. It snaps into place over the hinge area for a clean, secure fit. What it does

• Covers and protects the hinge mechanism from dirt and debris.
• Restores the appliance's finished appearance when the original cover is cracked or broken.
• Helps prevent accidental contact with moving hinge parts.
• Common symptom: visible broken or missing hinge trim exposing the hinge.

• One hinge cover assembly.

• Disconnect power (and water, if appliance type requires) before starting any repair.
• Remove any outer panels or trim as needed to access the hinge per the appliance service instructions.
• Handle plastic trim pieces carefully to avoid cracking during removal/installation.

This hinge cover assembly replaces a worn or damaged lid hinge cover to restore a smooth, finished look and protect the hinge area from debris and pinching. It helps keep the hinge area sealed and reduces snagging on the lid edge. What it does:

• Covers and protects the lid hinge and pivot area from dirt and moisture
• Restores a clean appearance where a cracked or missing hinge cover was visible
• Helps prevent clothing or hands from catching on the exposed hinge
• Can reduce rubbing noise caused by contact with a damaged cover

• Basic removal of the lid or access panel may be required; follow for proper disassembly
• Use appropriate hand tools and keep small fasteners secure during reassembly
• Disconnect power (and water for washers) before starting work to avoid injury

The Handle Assembly is an OEM part for LG refrigerator freezer compartments. It includes the handle and mechanical components that operate the freezer drawer.

Causes of a bad handle assembly can include fatigue from repeated opening and closing motions, damage sustained from heavy loads, or exposure to harsh chemicals over years of use.   

Symptoms of a bad handle assembly include:

• Handles detaching from the drawer front  
• Difficulty smoothly opening and closing the freezer drawer
• Inability to fully open or close the drawer
• Excessive play, wobble, or loose motion in the handle

Replace yours today with this genuine OEM LG assembly to restore effortless operation. This replacement handle is compatible with Frigidaire, Samsung, Whirlpool, and some Kenmore models.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This door foam assembly provides the inner insulation and support for a refrigerator door, helping maintain cold temperatures and preventing condensation where the foam sits. It restores proper door fit and insulating performance when the original foam is damaged or missing. What it does:

• Replaces deteriorated or missing inner door foam to help reduce heat transfer through the door
• Helps prevent localized condensation and frost buildup near the door panel area
• Restores proper door panel alignment and cushioning for the liner
• Can reduce uneven cooling or energy waste caused by compromised door insulation

• One door foam assembly

• Disconnect power to the appliance before beginning any repair
• Door panel or liner removal is typically required; keep fasteners organized for reassembly
• Handle the foam carefully to avoid tears; use plastic trim tools where possible to prevent damage

This is a door assembly that has been manufactured by LG for use with refrigerators. The door assembly includes multiple parts required for replacing the entire door, such as the inner liner and the outer panel. A working door is necessary for the refrigerator to maintain cold enough temperatures inside. If the current door is dented, bent, detached, or otherwise broken, it should be immediately replaced. This replacement might require two people, as the door is heavy. Take proper safety precautions, such as wearing work gloves and disconnecting the appliance from the power source.As a genuine OEM part, this door assembly has been sourced directly from the manufacturer and is only sold individually. This door assembly is manufactured from high-quality and durable materials to ensure durability. It is intended for use with refrigerators manufactured by LG.

The refrigerator door gasket seals the gap between the door and cabinet to keep cold air in and humid air out, helping maintain temperature, reduce frost and condensation, and restore a tight, reliable door close.

• Creates an airtight perimeter seal to prevent warm air leaks
• Helps stabilize interior temperature and humidity
• Minimizes frost buildup and condensation around the door
• Common symptoms: torn or deformed seal, door not sealing, moisture/frost near door, rising temps

What's included: 1 door gasket Installation notes:

• Disconnect power before servicing
• Allow the new gasket to warm to room temperature; soften in warm water or with gentle, low heat to relax folds
• Remove the old gasket and thoroughly clean the mounting channel/mating surfaces
• Seat the new gasket starting at the corners, then along the sides; ensure it's fully engaged and even all around, and check door alignment/seal

Restore a tight, reliable seal on your refrigerator door with this replacement gasket. A fresh gasket stops cold-air leaks that lead to frost, condensation, and temperature swings—helping your fridge run smoothly and keep food at the right temperature. What it does:

• Seals the gap between the door and cabinet to keep cold air in and warm air out
• Helps maintain consistent interior temperature and humidity
• Reduces frost and condensation around the door opening
• Common symptoms: torn or warped gasket, door not closing flush, moisture at the seal, frost buildup, or the unit running more than usual

• 1 door gasket

• Disconnect power before starting and clear items from the door
• Lay the new gasket flat and gently warm it (hot water or low-heat hair dryer) to relax folds
• Starting at the corners, press the gasket lip fully into the door channel and work evenly around
• Perform a paper-slip test around the perimeter and adjust door alignment if needed; avoid overheating the gasket

The Refrigerator Flipper Assembly is an OEM part for LG refrigerators. This assists in the smooth opening and closing of the refrigerator door. It ensures an airtight seal when the door is closed, preventing cool air from escaping and maintaining the refrigerator's internal temperature. 

Causes of a malfunctioning Refrigerator Flipper Assembly can range from physical damage, such as cracks or breakage, to wear and tear from regular use.

Symptoms of a bad Refrigerator Flipper Assembly include:

• Difficulty in opening or closing the refrigerator door
• A noticeable gap when the door is supposed to be sealed shut
• Increased energy consumption as the refrigerator works harder to maintain its temperature
• Spoilage of food items quicker than expected due to poor temperature regulation

This OEM LG part is also compatible with some Kenmore models.

This replacement door basket restores usable storage space on the refrigerator door, holding bottles, jars and small containers so food stays organized and easy to reach. Made to match the original fit and mounting points. What it does:

• Replaces a cracked, broken or chipped door basket that can no longer hold items securely
• Restores proper storage and keeps bottles and containers from shifting or falling
• Replaces missing or warped bins that prevent the door from sealing or organizing contents
• Compatible with factory mounting clips and shelf support locations

• Remove all food and loose items from the door before installing the new basket
• Most door baskets snap into place on molded supports; align tabs and press until secured
• Inspect mounting clips or supports for damage; replace clips if they are broken

The door basket is an OEM part for LG refrigerators. It is the basket located inside the refrigerator or freezer door that provides storage for smaller items like condiments, spreads, or snacks. The basket measures approximately 12" width x 3 1/4" height x 3 1/4" depth. 

Symptoms of a bad basket include:

• The door basket being loose, cracked, or damaged
• Difficulty removing or replacing the basket 
• Reduced storage capacity due to a warped or broken basket

Causes of a bad door basket can be normal wear and tear over time, exposure to excessive weight that stresses the plastic material, or accidental damage from dropping or impact.

This OEM LG part is also compatible with select Sears/Kenmore models.

The Door Bin is an OEM part for LG refrigerators. It provides convenient storage for items accessed regularly, from condiments to snacks.

Causes of a faulty door bin can include plastic cracking from extended usage, broken slide pegs, or a loose assembly. Regular temperature changes may compromise durability over time.

Symptoms of a problematic door bin include:

• Difficulty fully extending or retracting on glide tracks
• Contents are at risk of falling during opening/closing
• Rattling or vibrations while retrieving items

This LG part is also compatible with some Kenmore models.
 

STOPPER ASSEMBLY,DOOR

STOPPER ASSEMBLY,DOOR

This hinge cam fits the door hinge and provides the lift/settle action that helps the door open and close smoothly. Replacing a worn cam can reduce clicking and restore consistent door movement and alignment.

• Provides cam action at the hinge for smooth door travel
• Helps the door seat closed and maintain alignment
• Common symptoms include clicking/knocking at the hinge, rough or uneven door movement, or slight door sag
• Visual wear such as flat spots or grooves on the cam is a typical failure sign

• Disconnect power to the appliance before servicing
• Support the door to prevent injury; remove hinge cover and hardware as needed
• Note the cam's orientation and any washers/spacers and transfer them to the new part
• After installation, verify door operation and gasket alignment; adjust hinge if needed

The Lower Refrigerator Door Hinge is an OEM part for LG refrigerators. This hinge supports the refrigerator door, allowing it to open and close smoothly while maintaining proper alignment. It is designed to handle the weight of the door and ensure a secure and stable operation over time.

Causes of a bad lower refrigerator door hinge can include regular wear and tear, physical damage from overloading or impacts, and gradual loosening over time. A faulty hinge can lead to misalignment, difficulty in opening or closing the door, and potential damage to the door seal.

Symptoms of a bad lower refrigerator door hinge include:

• The door not closing properly or staying open
• Sagging or misaligned door
• Unusual noises when opening or closing the door
• Gaps in the door seal, causing cooling inefficiency

This OEM LG part is also compatible with Sears/Kenmore models.

The Door closer is an OEM part for LG refrigerators, this part prevents the refrigerator door from swinging open too widely. By limiting the door's range of motion, the Door Stop ensures that the door opens smoothly and safely, contributing to the longevity of the appliance and maintaining the aesthetic integrity of your kitchen space.

Causes of a bad Door closer can stem from physical damage, wear and tear over time, or loosening of the component due to repeated use. 

Symptoms of a bad Door closer include:

• The refrigerator door swinging open too far
• Damage or marks on adjacent walls or furniture from the door hitting them
• Increased wear on the refrigerator's hinges due to uncontrolled door movement

This OEM LG part is also compatible with some Kenmore models.

Handle assembly for refrigerator doors that restores a secure grip and smooth opening. Direct-fit replacement designed to match the factory handle for proper operation and appearance. What it does:

• Replaces damaged, cracked or loose refrigerator door handles
• Restores a secure grip for easier opening and closing
• Matches factory mounting points for a correct fit
• Reduces handle wobble and prevents snagging during use

• Basic hand tools are typically required; retain original screws and brackets unless replacement hardware was purchased
• Wear gloves and eye protection to avoid sharp edges during installation

This slide rail guides and supports a single appliance drawer or pull-out door so it opens and closes smoothly and stays aligned. Replaces a worn, bent, or noisy guide to restore proper movement and stability. What it does:

• Provides a rolling/sliding track for a drawer or pull-out door to travel smoothly
• Replaces damaged or worn rail that causes sticking, misalignment, or uneven movement
• Helps keep the drawer properly supported and prevents sagging or binding
• Works as a direct-fit replacement when the original rail is broken or worn

• One slide rail (single left or right guide)

• Disconnect power and empty the drawer before starting repairs
• Typical installation requires removing the drawer and fastening the rail with existing screws or clips
• Inspect mating hardware and replace any stripped screws or broken clips for secure fit

This slide rail is a direct-fit replacement that restores smooth, reliable movement to a refrigerator or freezer drawer. It replaces a worn or broken glide so the drawer opens and closes without sticking or sagging. What it does:

• Replaces a damaged or worn drawer glide to restore proper sliding action
• Supports the drawer to keep it level and reduce binding or sticking
• Reduces noise from grinding or scraping during drawer movement
• Helps maintain correct drawer alignment for proper sealing and operation

• Verify left/right orientation and part number before installation
• Remove contents and disconnect power if working near electrical components
• Typical installation uses existing mounting points and hardware; save original fasteners when possible

This ice maker gear drives the ejector blades that push ice from the tray into the bin. Replacing a worn or broken gear restores proper harvest cycles and stops grinding or slipping during ejection. What it does:

• Turns the ice maker ejector to release ice cubes during the harvest cycle.
• Stops or reduces grinding noises and slipping when the gear teeth are stripped or damaged.
• Helps restore regular ice production when the ejector no longer rotates.
• Works as the replacement driven gear in compatible LG ice maker gear trains.

• Disconnect power before servicing the ice maker to avoid shock or injury.
• Remove the ice maker assembly to access the gear; follow OEM instructions for disassembly.
• Inspect the mating gear, motor shaft, and ejector assembly for wear—replace additional damaged parts as needed.
• Use the matching part number to ensure fit.

This Supporter Cover is a replacement plastic trim piece that helps protect and secure TV internal components and rear housing. It restores proper fit and finish to the back of the TV for safe, stable operation. What it does:

• Covers and protects internal electronics at the rear of the TV from dust and incidental contact
• Helps hold adjacent housing pieces and panels in correct alignment
• Replaces broken, cracked or missing rear trim that causes loose or rattling panels
• Restores factory appearance where the original cover is damaged or lost

• One supporter cover

• Disconnect power and remove all cables before starting any repair
• Handle the cover gently to avoid snapping tabs; use proper trim tools if needed
• Remove required screws or clips from the rear housing to access and replace the cover

This center hinge assembly secures and allows smooth pivoting of the refrigerator's center door, restoring proper door alignment and closing. It replaces a worn or damaged hinge to reduce sagging and improve sealing. What it does:

• Provides the pivot point for the refrigerator's center door, maintaining correct door movement and alignment
• Helps the door close evenly to preserve the gasket seal and internal temperature
• Replaces broken, bent, or worn hinge hardware that can cause door sag or rubbing
• Works with existing hinge pins and mounting points to restore original function

• One center hinge assembly

• Requires basic hand tools; follow manufacturer instructions for removal and installation
• Support the door while removing or installing the hinge to prevent injury or damage
• Ensure all fasteners are tightened securely and door alignment is checked after installation
• Disconnect power if required by the appliance manufacturer before servicing

This center hinge assembly secures and pivots the upper/center refrigerator door, restoring proper door alignment and smooth opening. Designed to replace a worn, bent or broken center hinge to improve sealing and operation. What it does:

• Provides a mounting pivot for the upper/center refrigerator door to ensure correct swing and alignment
• Helps maintain an even door gap for a proper seal and consistent cooling
• Replaces damaged, bent or worn hinge components that cause rubbing, sagging, or noisy door movement
• Works with factory hinge pins and covers to restore original door function

• One center hinge assembly

• Installation requires removing the door and supporting it; have a helper to prevent damage or injury
• Use appropriate hand tools; avoid overtightening fasteners which can bind the hinge
• Inspect adjoining hinge pins and mounting screws; replace if worn for best results
• Disconnect power or follow manufacturer safety steps if working near electrical components

The Spanner Wrench is an OEM replacement part for LG refrigerators. This tool allows you to adjust the door hinges to ensure the doors are level and aligned properly. A well-aligned door is crucial for maintaining the internal temperature and efficiency of the refrigerator, preventing energy loss and ensuring food is stored under optimal conditions.

Symptoms that you might need to adjust the door hinges and potentially need this wrench include:

• Doors not closing properly or sealing tightly
• Visible gaps between the door and the main body of the refrigerator
• The refrigerator tilting or not sitting level

This spanner wrench is also compatible with some Sears/Kenmore refrigerators. 

This upper hinge assembly secures and guides the refrigerator door at the top, restoring proper alignment and smooth opening. Replace a worn hinge to stop sagging doors and improve sealing and operation. What it does:

• Provides the top pivot point for the refrigerator door, keeping it aligned during opening and closing
• Restores proper door clearance and prevents rubbing or misalignment
• Helps maintain a tight door seal to reduce cold air loss
• Addresses symptoms like a sagging or uneven door, noisy movement, or difficulty closing

• Disconnect power to the appliance before beginning repairs to prevent injury.
• Support the door while removing and installing the hinge to avoid dropping or damage.
• Use appropriate hand tools; do not overtighten fasteners to prevent stripping.

Replacement refrigerator door hinge that restores smooth pivoting and proper door alignment, helping the door open and close reliably and maintain an airtight seal to preserve cooling performance. What it does:

• Supports the refrigerator door and allows it to pivot smoothly.
• Replaces worn, bent, or damaged hinges that cause door sag or misalignment.
• Helps reduce noisy or grinding door operation when the hinge is failing.
• Promotes an even door seal to help maintain internal temperature consistency.

• Unplug the appliance and remove food from nearby shelves before starting work.
• Support the door while removing hinge fasteners to prevent dropping or damage.
• Reinstall using the original hardware; align the door and tighten fasteners securely but avoid overtightening.

This cap assembly replaces a damaged or worn dryer exhaust duct cap to restore proper venting and help keep pests and debris out of the ductwork. Fits the dryer's exterior duct outlet and guides hot, moist air outside. What it does:

• Seals and covers the dryer exhaust opening to reduce air leaks and backflow
• Directs exhaust airflow out of the home for proper drying performance
• Helps block pests, leaves and debris from entering the vent system
• Reduces moisture buildup and associated odor or lint accumulation near the duct opening

• One cap assembly

• Disconnect power (and gas supply on gas dryers) before beginning any work
• Remove the old cap and clean the surrounding duct and mounting surface before installing
• Secure with the existing fasteners or compatible screws and seal edges with foil HVAC tape if needed
• Inspect the connected ducting and lint trap while replacing the cap; replace damaged duct sections for best performance

This lever return spring restores proper tension to the lever assembly so the control or latch returns smoothly. A direct-fit replacement designed to restore normal lever movement and function. What it does:

• Provides return tension for the lever to ensure reliable latch or control movement
• Helps stop the lever from sticking or remaining engaged after use
• Restores smooth, consistent operation when the original spring is worn or broken
• Commonly replaced when lever movement feels loose or fails to return

• One spring lever

• Disconnect power (or unplug) and follow appliance safety procedures before servicing
• Access may require removing panels or the control/door assembly; keep fasteners organized
• Inspect mating lever and pins for wear; replace damaged components to prevent repeat failure

The Link is an OEM part for LG refrigerators. It serves as an integral connector between the refrigerator door and cabinet, facilitating smooth opening and closing of the door. With durable construction and precise engineering, the link is designed to withstand the rigorous motion of hundreds of door openings without compromising functionality. 

Symptoms of a bad link include:

• Doors that do not close or seal properly 
• Excessive noise or vibration from the door area
• Damage, bending, or breakage of the connecting pieces
• Misalignment impairing proper door operation

Causes can stem from normal wear and tear over many years of use. Replacing a faulty link restores the refrigerator door's designed motion for convenient access to the interior.

This OEM LG part fits seamlessly while extending the product's useful life. This part is also compatible with Kenmore models featuring LG's refrigerator link assembly design.

The Dispenser Lever is an OEM part for LG refrigerators. It operates as the primary method of dispensing ice and water through the dispenser compartment. The lever is an ergonomic handle that allows for easy activation of the dispenser with a simple push or pull motion.

Causes of a bad dispenser lever include broken hinges or joints from excessive force or repeated use over time. The plastic levers can also crack or break due to impact.

Symptoms of a bad dispenser lever include:

• The lever being stuck in the up or down position
• Difficulty activating or using the lever to dispense
• Cracks or breaks in the plastic housing

This OEM LG part is also compatible with some Kenmore models.

This overload protector is a compressor safety device that helps stop the compressor if it draws too much current or overheats, preventing damage and helping the refrigerator system run safely. What it does:

• Interrupts compressor power during excessive current draw or overheating to protect the compressor motor
• Can prevent short cycling and repeated restart attempts that damage the compressor
• Commonly replaced when compressor hums but will not start, or when the appliance stops cooling due to compressor protection
• Works as part of the compressor start/protection assembly alongside the start relay and capacitor

• Disconnect power to the appliance before accessing the compressor or electrical components
• Handle terminals carefully and reconnect to the matching terminals only; do not modify leads
• Verify the part number against the existing component before installation

This PTC thermistor assembly senses temperature and sends a signal to the appliance control so the unit runs at the correct temperature. Replacing a faulty thermistor restores reliable temperature feedback for proper operation. What it does:

• Monitors temperature and provides feedback to the appliance control board
• Helps control cooling/heating cycles by changing resistance with temperature
• Common symptom of failure: incorrect temperature readings or improper cycling
• May also cause extended run times, frequent on/off cycling, or no cooling

• Disconnect power to the appliance before starting any repair
• Handle the sensor and wiring gently; avoid kinks or sharp bends in the thermistor lead
• Test operation after installation and reassemble panels securely

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This cabinet roller supports the refrigerator and lets the unit roll in and out of place for cleaning or service. Replace a worn or broken roller to restore smooth movement and help keep the appliance properly positioned.

• Supports the base of the refrigerator and enables rolling movement
• Helps with safe positioning and service access without dragging
• Common failure signs: appliance is hard to move, scraping or rolling noises, a flat-spotted/cracked wheel, or a wheel that won't turn
• Replace when the roller is damaged, seized, or missing

• Disconnect power and shut off water supply; protect flooring before moving the appliance
• With help, pull the refrigerator forward and safely support it to access the roller
• Remove mounting fasteners, install the new roller, and reuse original hardware
• Confirm level and smooth movement before returning the unit to its location

Replacement fan guide that directs airflow from the refrigerator fan to improve cooling distribution and help keep the fan blade clear of nearby components. Restores proper airflow and can reduce rubbing or scraping noises. What it does:

• Channels airflow from the fan to promote even temperatures throughout the compartment.
• Keeps the fan blade aligned and away from cabinet walls and other components.
• Commonly replaced when cracked, warped, or broken parts cause rubbing or unusual fan noise.
• Helps maintain efficient cooling by restoring the intended airflow path.

• Disconnect power (unplug or shut off breaker) before servicing the appliance.
• Access typically requires removing the interior cover or rear evaporator cover.
• Handle the plastic guide carefully to avoid cracking; align mounting tabs and secure using the original fasteners.
• Inspect the fan blade and motor for damage while replacing the guide; replace any damaged components to avoid repeat issues.

The Fan Motor Assembly is an OEM part for LG refrigerators. It is responsible for circulating air throughout the refrigerator and freezer compartments to maintain consistent temperatures. By ensuring proper airflow, the fan motor helps to keep your food fresh and evenly cooled.

Over time, fan motors can wear out or become damaged due to factors such as dust buildup, electrical issues, or general wear and tear from continuous use. A faulty fan motor can lead to uneven cooling, increased energy consumption, and potential spoilage of food.

Symptoms of a bad fan motor include:

• Unusual noises coming from the refrigerator
• Inconsistent temperatures in the fridge or freezer
• The refrigerator running constantly or cycling on and off frequently
• Frost buildup in the freezer section

This OEM LG part is also compatible with Sears/Kenmore.

This compressor damper is a vibration-isolating mount that sits between the sealed-system compressor and the chassis. It cushions the compressor to reduce noise, limit vibration transfer, and help keep refrigerant lines from being stressed.

• Isolates the compressor from the frame to absorb start/stop shock and vibration
• Helps reduce humming, rattling, or buzzing from the back/bottom of the appliance
• Replaces a damper that's cracked, flattened, hardened, or missing
• Can help if the compressor rocks or the unit vibrates excessively

• Disconnect power and pull the unit forward for access; remove rear/service panel if present
• Support the compressor to relieve load on the mounts before removing fasteners
• Match orientation; transfer any sleeves/spacers from the old damper to the new one
• Ensure the compressor sits level and that tubing is not strained before restoring power

Replacement front cover that restores your appliance's exterior finish and helps protect controls and internal components from everyday wear, spills, and minor impacts, delivering a clean, finished look and proper front-panel fit. What it does:

• Covers and protects the appliance's front area, helping shield controls and wiring from dirt and moisture.
• Restores damaged or cracked front trim for improved appearance.
• Helps maintain proper alignment and fit of the front assembly.
• Common symptom: cracked, chipped, warped, or loose front panel that exposes internal parts or looks worn.

• Disconnect power (unplug or switch off breaker) before starting any repair.
• Basic hand tools (screwdriver set) may be required to remove the old cover and install the replacement.
• Handle edges carefully to avoid cuts; align tabs/clips and secure fasteners snugly but do not overtighten.

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

This restrainer is a small retaining clip that helps secure moving or removable components in place, reducing rattles and keeping parts aligned for reliable operation. It's a simple replacement for worn or broken clips. What it does:

• Holds a cover, panel, or door-related component in proper position to prevent shifting
• Reduces noise caused by loose or vibrating parts
• Restores original fit where a broken or missing clip allows movement
• Simple mechanical function — no electrical connections or calibration

• One restrainer

• Disconnect power (and water if applicable) before beginning repairs
• Inspect surrounding mounting points for damage; replace any broken tabs or fasteners
• Typically installs with basic hand tools; align clip and press or snap into place until secure

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

The Evaporator Fan Blade is an OEM replacement part for LG refrigerators. It is a key component located inside the refrigerator that works to circulate cold air evenly throughout. The fan blade spins rapidly to distribute chilled air from the evaporator coil and refrigeration system, ensuring proper airflow and consistent temperatures across all shelves and compartments.  

Symptoms of a bad evaporator fan blade include:

• Inconsistent or improper interior cooling temperatures 
• Hot or warm spots developing inside the refrigerator
• Strange noises such as clicking or grinding emanating from the rear wall

Causes of a bad evaporator fan blade can be wear and tear over time, an accumulation of dust or debris on the blades restricting airflow, or accidental damage like dents or cracks to the blades affecting their ability to spin smoothly.

This OEM LG part is also compatible with select Sears/Kenmore brand models.

This grille assembly replaces a damaged or worn fan cover to protect the appliance's internal fan and help direct airflow. Restores a secure fan opening and prevents debris or contacts that can impair fan performance. What it does:

• Protects the fan motor and blades from foreign objects, pets, and accidental contact
• Helps maintain proper airflow routing so the fan can cool or circulate air effectively
• Stops rattling or vibration caused by cracked or loose grille pieces
• Prevents airflow obstruction from broken trim that can lead to noise or reduced cooling

• One grille assembly

• Disconnect power to the appliance before starting any repair
• Keep track of mounting screws/clips and gently align grille to avoid cracking plastic tabs
• Inspect the fan blades and mounting while grille is off; replace damaged components as needed

The Dispenser Micro Switch is an OEM part for LG refrigerators. It is a component of the ice and water dispensing system, responsible for activating the dispenser when the lever is pressed. 

Causes of a bad Dispenser Micro Switch can include mechanical wear from frequent use, failure due to moisture or debris affecting the switch’s contacts, or electrical faults that prevent proper signaling.

Symptoms of a bad Dispenser Micro Switch include:

• The dispenser not releasing ice or water when the lever is pressed.
• Continuous dispensing or dripping after the lever is released.
• Intermittent or no response from the dispenser controls.

This OEM LG part is also compatible with Sears/Kenmore.

The Fan Guide Assembly is an OEM component specifically designed for LG refrigerators equipped with rear evaporator fans. This assembly guides proper airflow within the refrigerator compartment.

Symptoms of a bad fan guide assembly include:

• Development of warm or cool spots inside fridge surfaces  
• Excessive frost or moisture buildup at specific locations
• Reduced temperature fluctuation stability 
• Abnormally loud fan operation sounds

Causes of failure can be damage allowing fan blade strikes, cracks reducing structural integrity over time, or accumulation of dust clogging air passages.  

Replace yours today with this genuine OEM LG assembly to maintain optimized cooling throughout storage areas. Smooth, balanced airflow preserves food freshness evenly. This replacement part is compatible with Frigidaire, GE, and Samsung models for factory fit and function. Proper air distribution helps maintain energy efficiency.

The Evaporator Fan Motor Assembly is an OEM replacement part for LG refrigerators. This assembly is responsible for circulating cold air from the evaporator coils throughout the refrigerator and freezer compartments. By doing so, it ensures that both compartments maintain the desired temperatures and that the cooling process is efficient.

Causes for a malfunctioning Evaporator Fan Motor Assembly can include motor wear from continuous operation, electrical issues like faulty wiring, obstructions preventing the fan blades from turning, or damage to the fan blades themselves.

Symptoms of a bad Evaporator Fan Motor Assembly include:

• Inconsistent temperatures in the refrigerator or freezer compartments
• Unusual noises, such as humming or buzzing, coming from the back of the refrigerator
• Reduced cooling efficiency, leading to food spoiling faster
• Frost buildup in the freezer due to poor air circulation

This OEM LG part is also compatible with Sears/Kenmore model refrigerators.

A replacement cover motor that powers the refrigerator's dispenser cover, allowing the door to open and close so you can access ice and water. Replaces a worn or failed motor to restore normal dispenser cover operation. What it does:

• Drives the dispenser cover mechanism so the cover opens when dispensing and closes when idle
• Helps keep the dispenser sealed to reduce drafts and prevent pests or debris from entering
• Stops or fails to move when worn, causing a stuck, slow, or noisy dispenser cover
• Works with the dispenser linkage and gears to coordinate cover motion with user controls

• One cover motor

• Disconnect power to the appliance before beginning any repair
• Remove dispenser trim and access panel per your model's service instructions to reach the motor
• Handle gears and linkage carefully; ensure proper alignment during reassembly and test cover operation before finishing

Damper motor support secures the damper motor assembly inside the refrigerator, keeping the air-control damper aligned so it opens and closes correctly. Replacing a damaged support restores proper airflow control and reduces noise. What it does:

• Secures and positions the damper motor assembly so the air-control damper moves smoothly.
• Keeps the motor and damper aligned to help prevent rattling, grinding, or loose motor noise.
• Supports consistent airflow between compartments to assist with even cooling.
• Resolve damper movement problems like the damper not opening or closing fully.

• Disconnect power to the appliance before starting work; remove food and shelves as needed for access.
• Remove the interior access panel to reach the damper assembly; handle plastic tabs and clips gently to avoid breakage.
• Align the motor and damper during reassembly and secure all fasteners; test damper operation before replacing panels and shelving.

This damper motor support replaces a broken or warped mount for the refrigerator's air damper assembly. It holds the damper motor and door securely so the system can meter freezer air into the fresh food compartment.

• Secures and aligns the air damper motor/door within the duct
• Helps ensure proper opening/closing of the damper to regulate airflow and temperature
• Damage can contribute to a warm or too-cold refrigerator and inconsistent temperatures
• May cause clicking or buzzing from the damper area or a visibly loose assembly

• Disconnect power to the refrigerator before servicing
• Access the damper behind the fresh food compartment duct/cover; remove shelves as needed
• Note wiring and orientation; transfer the existing damper motor and door to the new support and reuse fasteners
• Ensure the door moves freely and seals before reassembly; restore power and verify airflow

The Ice Dispenser Door Motor is an OEM part for LG refrigerators. This motor is responsible for the operation of the ice dispenser door, controlling its opening and closing mechanism to allow ice to be dispensed without letting warm air into the freezer. 

Symptoms of a bad Ice Dispenser Door Motor include:

• The dispenser door not opening or closing properly,
• Ice not being dispensed when activated,
• Unusual noises coming from the dispenser mechanism.

Causes of ice dispenser door motor failure can include electrical issues such as shorts or wiring problems, mechanical wear over time, or blockages that strain the motor.

This OEM LG part is also compatible with Sears/Kenmore.

This door switch cover houses and protects the refrigerator/freezer door switch, keeping the switch secure and aligned so the interior light and door-sensing functions work reliably. It's a direct-fit replacement for damaged or cracked covers. What it does:

• Protects the door switch from impacts, spills, and debris that can cause intermittent contacts or failure
• Keeps the switch properly positioned so the interior light turns on/off when the door opens and closes
• Helps ensure consistent door-sensing for control logic that manages defrost and cooling cycles
• Reduces the risk of moisture reaching the electrical switch components

• One door switch cover

• Power off and unplug the appliance before beginning any repair to avoid shock or damage
• Handle gently to avoid breaking the plastic tabs; some models use snap-in tabs or screws for mounting
• Verify switch alignment and operation before fully reassembling the door trim
• Replace the switch assembly as needed

This sheath-style heater melts frost from the evaporator during automatic defrost cycles to keep airflow clear and temperatures stable. Replacing a failed heater helps stop recurring ice buildup and restore consistent cooling performance.

• Heats the evaporator to melt accumulated frost/ice during defrost
• Keeps air passages clear to maintain proper temperatures
• Helps prevent frost-packed evaporator covers and reduced cooling
• Common symptoms: heavy frost behind the freezer panel, fan noise from ice contact, weak cooling, long run times

• Disconnect power before servicing; allow any sharp edges to be avoided with cut-resistant gloves
• Access is typically behind the freezer's rear interior panel; remove shelves/drawers and panel to reach the evaporator
• Transfer any clips/sensors attached to the heater in the same positions; avoid bending fins or puncturing refrigerant lines
• Ensure connectors are fully seated and the heater is secured before restoring power and monitoring operation

This LED assembly is a backlight strip used to illuminate the display for clear, even picture brightness. Replacing a faulty strip restores proper screen illumination and can eliminate dark spots or missing segments. What it does:

• Provides the LED illumination source behind the LCD panel for even brightness
• Restores lost or uneven backlighting caused by failed LEDs or damaged strips
• Commonly replaces parts that cause dimming, flickering, or no light on power-up
• Connects to the display's LED driver board to receive power and signals

• Disconnect power and remove the display panel before replacing
• Handle the strip and connector carefully to avoid bending or damaging LEDs and flex cables
• Observe ESD precautions and avoid touching LED surfaces or circuit traces
• Reassemble panels and test before finalizing to ensure proper alignment and function

This power cord assembly provides the mains connection for compatible LG appliances, restoring reliable power delivery so the unit can run safely and consistently. Use when the original cord is damaged or the appliance loses power. What it does:

• Replaces a worn, frayed, or damaged power cord to restore safe electrical connection
• Carries line, neutral, and ground (where applicable) from the outlet to the appliance
• Helps resolve symptoms such as no power, intermittent power, or visible cord damage
• Maintains factory-fit routing and terminal connections for proper installation

• One power cord assembly as pictured

• Disconnect power at the breaker or unplug the appliance before installing
• Tighten terminal screws securely and route the cord to prevent pinching or chafing

This Main PCB Power Control Board Assembly replaces the appliance's primary electronic control module to restore power distribution and control of key functions. It helps address intermittent power, failure to start, or unresponsive controls. What it does:

• Regulates and routes power to motors, valves, and user interface components
• Interprets user commands and runs programmed cycles
• Stops operation or errors when board faults occur
• Common symptom: unit won't start, displays errors, or has unresponsive buttons

• One Main PCB Power Control Board Assembly as shown

• Disconnect power before accessing the control board to avoid shock
• Handle the PCB by edges and avoid static discharge; use an ESD strap if available
• Verify connector seating and cable routing during reinstall; do not force connectors

This ice maker assembly replaces a failed refrigerator ice maker to restore automatic ice production and reliable cube harvesting. Use it to address lack of ice or irregular ice cycling so your appliance makes ice again. What it does:

• Freezes and cycles water into ice, then harvests cubes into the ice bin.
• Common replacement for no ice production, reduced output, or an ice maker that won't cycle.
• Helps isolate ice-maker failures from water-supply or valve issues when diagnosing ice problems.

• Always disconnect power and shut off the water supply before beginning service.
• Some installs require removing shelves, drawers or interior panels.
• Basic hand tools are typically all that's needed; handle electrical connectors and the fill tube carefully.
• If issues continue after replacement, verify water supply pressure and the water inlet valve.

The Auger Motor is an OEM part for LG refrigerators. It is responsible for dispensing ice from the icemaker into the ice bucket. 

Symptoms of a bad auger motor include:

• Slow or incomplete ice filling of the ice bucket
• Ice clumping or jamming in the auger assembly 
• Grinding or rubbing noises coming from the icemaker region
• The icemaker not producing any ice at all

Causes of a bad auger motor can be wear and tear over time, freezing or ice buildup preventing proper operation, or failure of internal motor components. 

This OEM LG part is also compatible with select Sears/Kenmore models. 

The Water Line Connector is an OEM replacement part for LG refrigerators. It is responsible for connecting the water supply line from the home plumbing to the refrigerator's internal water distribution system, allowing for ice and water dispenser functionality. 

Causes of a bad water line connector can include cracking, leaks, or deterioration of the connector material over time due to regular water pressure and temperature fluctuations. Connectors may also become damaged if exposed to impact.

Symptoms of a bad water line connector include:

• Leaks at the connection point between the line and refrigerator
• Loose, slipping, or disconnected water line fitting  
• Reduced water pressure or no water flow to the dispenser
• Error codes related to water flow from the refrigerator diagnostics

 This OEM LG part is also compatible with Sears/Kenmore refrigerators.

The Clip is an OEM part for LG refrigerators. This clip secures the water tube in place, preventing it from moving or becoming disconnected. It plays a crucial role in maintaining the proper flow of water to the ice maker and water dispenser.

Causes of a bad water tube clip can include physical damage, wear and tear from regular use, or brittleness due to temperature fluctuations. If the clip fails, it can result in leaks or disconnections, disrupting the water supply.

Symptoms of a bad water tube clip include:

• Water leaks inside or outside the refrigerator
• The water tube becoming loose or disconnected
• Reduced or no water flow to the ice maker or water dispenser

This OEM LG part is also compatible with Sears/Kenmore refrigerators.

This sensor PCB assembly detects and relays sensor signals to the appliance control system, restoring accurate sensor feedback and communication when the original sensor board fails or malfunctions. Designed as a direct replacement board. What it does:

• Reads sensor inputs and converts them to signals the main control board can interpret.
• Replaces a failed or intermittent sensor board that causes incorrect readings or sensor-related error codes.
• Can resolve symptoms such as unexpected sensor faults, control errors, or appliances not responding to sensor changes.
• Matches the OEM board function; verify model compatibility before ordering.

• Always disconnect power before servicing to avoid shock or shorting the board.
• Use ESD precautions and handle the PCB by its edges to prevent static damage.
• Ensure all connectors are fully seated and the board is mounted in the original orientation.

This sub PCB assembly is an electronic control board that processes inputs and switches components, coordinating specific appliance functions. Replacing a failed board can restore normal operation and resolve dead controls, error codes, or intermittent, unpredictable behavior. What it does:

• Distributes and regulates control power and switches loads via onboard relays/triacs
• Interprets signals from sensors and the user interface to execute commands
• Coordinates timing and operation of related components per the appliance's program logic
• Failure may present as no power, won't start, unresponsive or flickering display, random beeps, or recurring error codes

• 1 sub PCB assembly

• Disconnect power to the appliance before servicing; verify no voltage is present
• Use ESD protection and handle the board by the edges
• Photograph wiring; transfer connectors one at a time and ensure they are fully seated
• Secure the board with existing fasteners/standoffs; perform any required reset or diagnostic per your model's service info

The Temperature Sensor is an OEM part for LG refrigerators. Also known as a thermistor, is responsible for sensing the temperature changes and providing the necessary feedback to the refrigerator's control board. It helps maintain accurate and consistent temperature levels, ensuring optimal food preservation and efficient cooling.

Causes of a faulty temperature sensor can include wear and tear over time, damage due to electrical issues or exposure to extreme temperatures, or sensor calibration issues. These factors can result in temperature inconsistencies, inaccurate readings, or improper cooling performance of the refrigerator.

Symptoms of a bad temperature sensor may include:

• Incorrect temperature readings on the control panel
• Temperature fluctuations inside the refrigerator
• Overcooling or inadequate cooling of food items

This OEM LG part can also be used on Kenmore/Sears appliances. 

This ice bucket assembly is the removable storage bin that collects and holds cubed ice from the refrigerator ice maker, restoring clean, contained ice storage and proper pickup by the dispenser or scoop. What it does:

• Collects and stores cubed ice produced by the ice maker so ice is contained and ready for use
• Guides ice toward the dispenser/auger area for consistent pickup
• Common symptoms it addresses: cracked or warped bin, ice spilling or falling out, ice not accumulating in the bin
• Fits into the freezer ice maker area and works with the factory guides and ejector mechanism

• Disconnect power to the refrigerator before servicing to avoid injury or damage
• Remove existing bucket by sliding it out of the guides; handle plastic parts gently to avoid cracking
• Reinstall by seating the bucket into the guides until it clicks or seats securely; ice maker components align before restoring power
• After installation, cycle power or run a test ice-making cycle to ensure proper operation

This ice dispenser assembly replaces the dispenser mechanism in compatible LG refrigerator doors, restoring smooth ice delivery and helping stop jams or broken chutes so your dispenser works reliably again. What it does:

• Channels ice from the freezer bin through the door to the dispenser chute.
• Activates the dispenser mechanism to release ice when the paddle/lever is pressed.
• Common symptom fixes: ice not dispensing, ice jams, cracked or damaged chute, or loose/disconnected dispenser components.
• Helps restore normal dispenser operation without replacing the entire door assembly.

• Disconnect power to the refrigerator before beginning any repair.
• Access typically requires removing the refrigerator door panel/liner and disconnecting the dispenser harness; follow the OEM service manual for procedure.
• Handle plastic chute components carefully to avoid cracking; check connector seating and alignment during reassembly.
• Test dispenser function after reinstalling the panel.

The Water Tank Assembly is an OEM part for LG refrigerators. It stores and supplies water for the refrigerator's dispenser and ice maker, ensuring a steady and clean water flow for these features.

Causes of a bad water tank assembly can include mineral buildup from hard water, leaks due to cracks or punctures, or contamination from mold or bacteria if the tank is not regularly cleaned. Over time, wear and tear from repeated use can also lead to failure.

Symptoms of a bad water tank assembly include:

• Water dispenser not functioning properly
• Reduced or no ice production
• Leaks or puddles inside the refrigerator
• Unpleasant taste or odor in the water

This OEM LG part is also compatible with Sears/Kenmore refrigerators.

This connector tube provides a sealed water path between refrigerator water components to restore proper water flow and reduce leaks. It's a direct-fit replacement when your existing connector is cracked, clogged, or damaged. What it does

• Re-establishes a secure water connection between dispenser/ice-making components.
• Restores water flow so the ice maker and dispenser can fill properly.
• Prevents drips and leaks from damaged or degraded tubing joints.
• Helps eliminate intermittent filling or reduced water flow caused by collapsed tubing.

• One connector tube.

• Disconnect power and shut off the water supply before beginning any work.
• Use proper fittings or clamps and tighten securely—avoid over-tightening plastic fittings.
• After installation, turn on the water and check all connections for leaks; discard any damaged or brittle tubing.

This water line holder secures and routes the refrigerator's plastic water tube so it stays protected and out of the way. Replacing a damaged holder helps prevent kinks and leaks and keeps water flowing to the dispenser and icemaker.

• Anchors and guides the water tube along the cabinet/door to prevent rubbing and kinking
• Helps maintain proper water flow to the dispenser and ice maker
• Replace if the holder is cracked, missing, or the tube won't stay seated
• Symptoms can include leaks or drips near the hinge/backs, slow or no dispensing, or visibly loose tubing

• Disconnect power and turn off the household water supply before servicing
• Access the holder (often behind a hinge cover, kick plate, or rear panel)
• Note tube routing, then release/remove the old holder and seat the tube in the new holder; reuse existing hardware if present
• Restore water and power; check for leaks and normal dispenser/ice operation

This inlet water valve assembly controls and directs incoming water to the appliance, restoring proper fill operation and water delivery. It replaces a worn or failed valve to help stop no-fill, slow-fill, or continuous-fill issues. What it does:

• Opens and closes supply passages to allow water into the appliance when needed
• Directs cold and/or hot water to the correct internal circuits
• Stops water flow when the fill cycle completes to prevent overfilling
• Faulty valves can cause no water, weak filling, or constant filling symptoms

• Disconnect power and turn off the water supply before starting any repair
• Handle inlet hoses and fittings carefully; check seals and replace gaskets if shown damaged
• Test for proper fill function and leaks after installation

The Water Valve is an OEM component specifically designed for LG refrigerators equipped with internal dispensers. Located inside the refrigerator wall, this valve regulates water flow to the dispenser spigot on demand. Through precise operation, it provides consistently refreshed chilled water.  

Causes of a bad water valve can include mineral buildup restricting flow passages over time, or physical damage disrupting seals.

Symptoms of a bad water valve include:

• No water was dispensed from the spout
• Leaks in the refrigerator compartment 
• Foreign odors emitted around the valve area

This authentic LG valve restores the dispenser function, delivering clean water efficiently. Its self-closing design helps prevent leaks when not in use. Replace to satisfy LG quality and support luxury features like internal filtration performing dependably for years.

This OEM LG part also fits select Kenmore refrigerator models using LG-developed components and controls for a premium user experience.
 

This water inlet valve assembly regulates the flow of household water into your refrigerator. Replacing a sticking or leaking valve restores proper fill for ice production and dispensing and helps stop drips, low flow, and overfill issues.

• Opens and closes to control water flow from the supply line into the refrigerator's water system
• Directs water to the ice maker and dispenser as commanded by the control system
• Seals off when closed to prevent seepage or dispenser drip
• Common failure symptoms: no ice, no or slow dispenser water, leaking at the valve or connections, humming/buzzing from valve with no water flow

• Unplug the refrigerator and shut off the household water supply before servicing
• Pull the unit forward for access; relieve line pressure and place a towel or pan to catch residual water
• Note tubing and wire locations; move them one at a time to the new valve and avoid overtightening fittings
• Restore water and power, check all connections for leaks, and dispense water to purge air from the system

This mechanical mounting band secures a bracket assembly inside the appliance to keep components aligned and reduce vibration. It restores proper bracket positioning so moving parts run quietly and reliably. What it does:

• Holds a bracket or component assembly in place to maintain proper alignment
• Dampens movement and reduces vibration-related noise or rattling
• Prevents excess wear by keeping parts from shifting during operation
• Helps maintain correct clearances to avoid interference or rubbing

• Disconnect power before inspecting or replacing internal parts
• Remove only the fasteners necessary to access the bracket; keep track of hardware
• Secure all fasteners to the manufacturer's torque or snug specification
• Replace the band if bent, cracked, or missing to restore proper fit and function

This is a replacement filter cover that secures the air filter in place and protects internal components. It restores the proper fitment of the filter and helps maintain intended airflow and filtration performance. What it does:

• Holds the air filter securely so air passes through the filter media as designed
• Protects internal components from dust and debris
• Prevents gaps that can reduce filtration efficiency or allow unfiltered air bypass
• Helps reduce rattling or vibration caused by a loose or damaged cover

• One filter cover

• Disconnect power before accessing internal parts
• Remove the old cover by releasing retaining tabs or fasteners and align new cover until it snaps or locks into place
• Inspect nearby seals and the filter; replace if damaged
• Handle plastic parts gently to avoid cracking; do not force into place

This water filter assembly replaces the refrigerator's water filtration module to help restore clear-tasting water and steady flow. Fits models that use the AGF80300705 assembly and installs at the refrigerator water inlet. What it does:

• Filters sediment and common taste/odor contaminants to improve drinking water quality
• Restores reduced water flow caused by a clogged or failing filter module
• Helps reduce visible particulates and cloudiness in dispensed water
• Prevents unfiltered water from reaching the dispenser/ice maker when installed

• Turn off refrigerator water supply before replacing the assembly to avoid leaks
• Hand-tighten connections; avoid overtightening fittings to prevent damage
• Run and discard the manufacturer-recommended initial volume of water after install to flush the system

The Filter Head Assembly is an OEM replacement part for LG French door refrigerators. The component that houses the built-in water filter responsible for cleaning water delivered through the refrigerator’s internal dispenser and ice maker. With its precise fit, the filter head assembly ensures the water filter is securely held in place to do its job properly.

Symptoms of a bad filter head assembly include:  

• Water dispensing or ice making issues
• Water leaks around the filter area  
• Error messages related to filter replacement
• Inability to change or install a new filter

Causes of failure can be cracks, cracks, mineral buildup, or normal wear over time. Filter head assemblies in continuous use may need periodic replacement.

This OEM part is also compatible with some Kenmore side-by-side refrigerators.

This genuine replacement filter cover secures and protects the unit's air filter, helping keep the filtration system sealed and operating as designed. Restores proper fit and helps maintain airflow through the filter assembly. What it does:

• Holds the air filter in place and protects the filter media from debris
• Helps maintain correct airflow through the filter chamber for effective filtration
• Prevents gaps that can allow unfiltered air to bypass the filter
• Restores a secure fit if the original cover is cracked, warped, or missing

• One filter cover

• Disconnect power to the appliance before removing or replacing the cover
• Remove the old cover by releasing any clips or tabs, then snap or slide the new cover into place
• Inspect surrounding seal/gasket and filter media for damage while installing
• If clips or tabs are damaged, replace them before operating the appliance

This complete freezer door assembly replaces a damaged or worn freezer door to restore proper closure and cold retention. It fits the freezer compartment and includes the door shell and attached inner components for a like-for-like replacement. What it does:

• Replaces a cracked, dented, or warped freezer door to help prevent cold air loss
• Restores proper door alignment and sealing to reduce frost buildup and temperature issues
• Provides the original mounting points and inner components for easy fitment
• Helps the freezer maintain consistent performance when the old door can't close or seal properly

• Disconnect power to the appliance before starting any repair
• Remove food and shelves from the freezer area for access and safe handling
• Installation typically requires basic hand tools; support the door during removal/installation to avoid injury or damage
• If the door contains glass or trim, handle carefully.

This lower ice bank door hinge secures and pivots the freezer's ice bank door so it opens and closes smoothly, helping maintain proper sealing and ice dispensing alignment. Designed as a direct replacement for the original hinge. What it does:

• Supports the ice bank door, providing a stable pivot point for opening and closing
• Keeps the ice bank door aligned to maintain an effective seal and proper operation
• Prevents sagging or binding that can interfere with ice dispensing or door function
• Restores correct door movement after hinge wear or damage

• Use basic hand tools; keep power to the appliance off and unplug before starting
• Handle the ice bank and door carefully to avoid damaging the trim or ice chute
• Reuse original fasteners only if undamaged; replace damaged screws to ensure secure mounting

This door gasket assembly replaces a worn or damaged refrigerator door seal to help restore an airtight seal and maintain proper cooling. A properly seated gasket reduces drafts, moisture intrusion, and energy loss. What it does:

• Seals the refrigerator door to keep cold air in and warm air out.
• Helps prevent frost buildup and moisture accumulation inside the compartment.
• Reduces compressor run time and energy usage caused by a leaking seal.
• Addresses symptoms such as warm spots, visible gaps around the door, or condensation on the door edges.

• Disconnect power to the appliance and remove food from the door area before starting.
• Inspect the door flange for damage and clean the mounting surface to ensure a proper seal.
• Seat the gasket fully into the channel; some models require loosening or removing trim screws to install.
• If the door does not close evenly after installation, check hinge alignment and adjust per the OEM instructions.

The Lever Cover is an OEM part for LG refrigerators. This cover fits neatly over the freezer door lock mechanism, protecting its internal lever and hardware.

Causes of a bad lever cover can include damage from regular opening and closing of the freezer door over time. Accidental impacts or heavy impacts from moving the refrigerator could also crack or weaken the plastic material.

Symptoms of a bad lever cover include:

• Exposure of the lock mechanism that allows dust and debris to enter
• Improper shielding of lock parts leading to potential jamming issues
• Cracking or breakage of the plastic allowing outside contaminants inside

This OEM LG part is also compatible with some Kenmore models.