Parts for Frigidaire E23BC78IPSF: 17 - Ice Maker Parts

Ice maker not filling or water dispenser not working? This refrigerator water inlet tube routes water from the valve to your dispenser and ice maker system.

Ice bin filled with solid ice block? Cracked ice tray leaking water into bin? This ice maker assembly fixes freezing issues. 15-minute DIY install.

Frost buildup or no defrosting? This defrost thermostat monitors evaporator coil temperature to trigger defrost cycles. DIY-friendly repair, 30-45 minutes.

Fix ice buildup in freezer or water leaking into fridge. This defrost heater melts frost from evaporator coils during defrost cycles. Moderate DIY repair.

Molded support housing that mounts and protects internal refrigerator components. Replace if cracked, broken, or damaged to restore secure fit and alignment.

Ice maker stopped working or water dispenser not flowing? This refrigerator water valve controls water to both. Easy 10-20 minute DIY fix with video.

This replacement cover is an access panel that restores the appliance's exterior finish and protects internal components from dust and debris. It fits into the original mounting points and matches the OEM shape for a clean, factory appearance. What it does:

• Shields internal components and wiring from dirt and accidental contact
• Restores a uniform exterior surface for proper airflow and appearance
• Helps prevent small objects from entering service areas that could cause issues
• Suitable when the original cover is cracked, warped, or missing

• One replacement cover as shown

• Use basic hand tools to remove fasteners and lift off the old cover before installing the new one
• Align mounting tabs and secure with original screws; do not overtighten to avoid cracking the plastic
• Disconnect power at the breaker or unplug the appliance before servicing to avoid shock or injury
• Replace damaged mounting hardware before completing installation

Replacement cover that restores appliance appearance and protects internal components from dirt and damage. Installs in place of a worn, cracked or missing cover to keep controls and wiring safely concealed and the unit looking finished. What it does:

• Protects the control area and internal components from spills, dust, and accidental contact.
• Hides and secures wiring and mounting points to prevent snagging or tampering.
• Restores the appliance's finished look when the original cover is scratched, cracked, broken, loose, or missing.
• Helps reduce the chance of debris entering sensitive areas that can affect performance.

• One replacement cover.

• Disconnect power (unplug or shut off circuit breaker) before attempting any service.
• Basic hand tools are typically required; support the cover while removing fasteners to avoid dropped parts.
• Handle edges carefully to avoid cuts and to prevent scratching adjacent surfaces.
• Refer to the appliance's service manual or model-specific instructions for exact removal and reinstallation steps.

This water tube routes potable water inside the refrigerator to the dispenser and/or ice maker, restoring normal water delivery and preventing leaks. It's a direct-fit replacement that helps maintain proper ice and water operation. What it does:

• Channels water from the refrigerator inlet/valve to the dispenser or ice maker
• Replaces cracked, kinked or punctured tubing that causes leaks
• Stops intermittent or no-water delivery caused by damaged tubing
• Restores steady water flow for ice production and dispensing

• Turn off the refrigerator power and shut off the water supply before starting
• Inspect connection fittings and tubing route; replace any worn clamps or seals as needed
• Use appropriate tools to loosen and tighten fittings without over-torquing

Foam insulation panel for refrigerators. Installs inside cabinet walls to maintain temperature efficiency. Replace if cracked, compressed, or missing.

Secures tubes and wiring in your refrigerator. Replace if clips are broken or connections are loose. Confirm fit with your model number.

Water inlet tube for refrigerators. Connects the water supply to the dispenser or ice maker. Replace if cracked, kinked, leaking, or damaged.

Replacement mounting screw for refrigerator panels, brackets, and trim. Secures loose or missing fasteners to stop rattles and keep components aligned.

Connects refrigerator water line to inlet or valve with secure seal. Replace if cracked, leaking, or damaged to restore proper water pathway connection.

H-shaped gasket seals evaporator housing to control airflow and reduce frost buildup. Replace if worn or cracked to restore cooling. Verify fit with model.

Fix no water or ice issues with this refrigerator water tube. Restores flow from inlet valve to dispenser and ice maker when the original is cracked or leaking.

Ice maker leaking water or producing malformed cubes? A cracked water fill chute allows water to leak instead of filling properly. Simple snap-in repair.

Connects sections of water tubing inside your refrigerator. Replace this adapter if cracked, leaking, or popping off to stop drips and water damage.

Replacement mounting screw for refrigerators and freezers. Secures shelves, handles, panels, and brackets. Replace missing, stripped, or rusted screws.

The Fill Tube Kit is an OEM part for Frigidaire refrigerators. It contains the tubes used to direct water from the water supply line into the refrigerator's water dispenser and ice maker. As these tubes can degrade over time due to mineral buildup or cracking, this kit provides a like-new replacement to ensure optimal water flow.

Causes of a bad fill tube include mineral or limescale deposits restricting water flow, cracks or leaks developing from general wear and tear, or accidental damage from installation or maintenance issues.

Symptoms of a bad fill tube are:

• Slow or inconsistent water flow from the dispenser
• Dripping or leaks from the fill tube connection points
• Ice maker not working or producing small or misshapen ice cubes
• Water backing up or overflowing in the refrigerator

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Ice buildup in fresh food section or around evaporator? This air handler housing kit stops warm-air leaks that cause frost and temperature swings. 30-min repair.

Ice buildup in fresh food section or around evaporator? This air handler housing kit stops warm-air leaks that cause frost and temperature swings. 30-min repair.

Ice buildup in fresh food section or around evaporator? This air handler housing kit stops warm-air leaks that cause frost and temperature swings. 30-min repair.

Ice buildup in fresh food section or around evaporator? This air handler housing kit stops warm-air leaks that cause frost and temperature swings. 30-min repair.

Ice buildup in fresh food section or around evaporator? This air handler housing kit stops warm-air leaks that cause frost and temperature swings. 30-min repair.