Parts for Maytag MFI2269FRE01: 10 - Icemaker And Ice Container Parts

This ice bin assembly stores the cubes your icemaker produces and makes them easy to access or dispense. Replacing a cracked or worn bin prevents spills and jams and keeps your refrigerator's ice service working smoothly.

• Collects and holds ice produced by the icemaker
• Slides in and out for convenient ice access
• Helps prevent stray cubes and spills inside the freezer
• Common symptoms of failure: cracked or broken bin, ice spilling, difficulty dispensing or removing ice

• Disconnect power before servicing for safety
• Empty and remove the old bin per your model's procedure
• Seat the new bin fully on its rails or locator tabs
• Restore power, make a small batch of ice, and check operation

This replacement motor restores powered rotation to the assembly it drives, bringing smooth, dependable operation back to your appliance. Replacing a weak, noisy, or seized motor can resolve no-run or intermittent performance of the connected function. What it does

• Converts electrical power into controlled shaft rotation to operate the connected mechanism
• Failure signs can include humming or grinding noises, overheating odor, or the feature not starting
• Excess vibration or heat can indicate worn bearings or windings

• 1 motor

• Disconnect power (and shut off water if applicable) before servicing
• Note wire connections and orientation; transfer any brackets, grommets, or attached parts from the original motor if required by your model
• Ensure the shaft spins freely and clearances are correct before reassembly
• Restore power and test; monitor for abnormal noise or heat on first run

This blower wheel moves air through the appliance's ventilation system so clothes dry evenly and components stay cool. It restores proper airflow to improve drying performance and reduce overheating risk. What it does:

• Spins to circulate air through the drum and exhaust vent for efficient drying
• Replaces a damaged or broken wheel that can cause reduced airflow and long dry times
• Stops abnormal noises from a cracked or out-of-balance impeller
• Helps prevent overheating caused by restricted or insufficient airflow

• Disconnect power (and gas, if applicable) before beginning any repair
• Inspect the mounting shaft, housing, and fasteners; replace any damaged hardware
• Ensure correct wheel orientation and secure fit to avoid vibration or rubbing

A small rubber mounting grommet that cushions and protects components where they pass through or sit against a chassis or housing. Replaces worn or damaged grommets to reduce vibration and keep parts properly positioned. What it does:

• Provides a vibration-dampening cushion for mounted parts or wiring
• Protects wires, hoses, and metal edges from abrasion at pass-throughs
• Helps keep components aligned and secure during operation
• Worn or cracked grommets can cause rattling, rubbing noises, or movement of parts

• One replacement rubber grommet

• Disconnect power before starting any repair
• Access may require removing panels or trim—refer to your model's service manual or diagram
• Inspect surrounding parts and replace any additional worn fasteners or seals as needed
• Use appropriate tools and take care not to damage wiring or components when installing

This replacement divider restores separation and organization inside the refrigerator so food stays grouped and doesn't shift during normal use. It fits into the interior shelf/drawer area to help keep items tidy and accessible. What it does:

• Separates storage space to keep foods organized and prevent shifting
• Helps maintain clear zones for different items
• Replaces cracked, broken or missing dividers that allow items to fall or mix
• Matches OEM fit to sit securely in the shelf or drawer track

• One replacement divider

• Remove food and sliding drawers or shelves before installing to avoid spills
• Align divider tabs with the shelf/drawer tracks and press into place until it seats securely
• Use gloves to protect hands from sharp shelf edges

This gasket for the damper assembly provides a replacement seal that helps keep compartments properly isolated and reduces air leakage. Replacing a worn gasket restores more consistent airflow and supports stable internal temperatures. What it does:

• Seals the damper opening to reduce unwanted air transfer between compartments.
• Helps the damper close and regulate airflow for more consistent temperature control.
• Common symptoms of a failing gasket: temperature swings, frost or moisture buildup, and noisy or improperly closing damper.
• Restoring a proper seal can improve cooling consistency and help avoid overworking the compressor.

• Disconnect power to the appliance before attempting service.
• Remove interior items and any trim panels needed for damper access; use gentle prying to avoid damage.
• Seat the new gasket fully into the damper groove and verify smooth damper movement before replacing panels and contents.

The Auger Motor is an OEM part for Frigidaire refrigerators. This motor powers the auger in the refrigerator's ice maker unit. The auger rotates during ice-making, ejecting ice from the mold and depositing cubes into the storage bin.  

Causes of a bad auger motor can include wear and tear over time from continuous use, or damage from unbalanced ice molds or debris buildup.

Symptoms of a bad auger motor include:

• Ice maker not producing ice or producing ice inconsistently  
• Ice cubes jammed or frozen together in the storage bin
• Loud buzzing or grinding noises coming from the ice maker area
• Inability to eject ice properly into the storage bin

Replacing this OEM Frigidaire auger motor helps ensure consistent, reliable ice production. This replacement part is compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Electronic air damper control assembly for the refrigerator. It regulates the flow of cold air from the freezer into the fresh food compartment to keep temperatures consistent, helping prevent warm spots or over-cooling that can freeze items.

• Opens and closes a damper door to meter airflow from the freezer into the refrigerator
• Helps maintain set temperatures and balanced airflow between compartments
• Resolves symptoms such as a warm fresh-food section, items freezing in the refrigerator, temperature swings, weak/no airflow from the diffuser, or clicking/buzzing noises from the damper area

• Disconnect power to the refrigerator before servicing; use gloves to protect from sharp edges
• Remove shelves and the air duct/cover to access the damper; keep fasteners for reuse
• Unplug the wiring connector, release locking tabs, and install the new assembly fully seated and aligned
• Restore power and verify damper operation and airflow before reloading the compartment

This replacement screw secures specified refrigerator components—such as covers, brackets, and internal panels—so they stay properly mounted. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and reliable operation.

• Provides the correct fastener for locations identified in your model's parts diagram
• Helps prevent looseness, vibration, and rattling of panels or brackets
• Replace if the head is stripped, threads are worn, or the screw is missing
• Symptoms can include loose parts, gaps, or noises from movement

• Unplug the refrigerator and shut off water if working near the ice maker or dispenser
• Match length and type to the original; follow your model's parts diagram for placement
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Keep track of screw positions; do not mix different screw lengths or styles

The Spacer is an OEM component specifically designed for Whirlpool side-by-side refrigerators. Located within refrigerator door walls, it maintains precise alignment between internal insulation and outer door panels.

Causes of a bad spacer include cracks or breaks developing from repeated door openings and closings. Prolonged very low temperatures can also make plastic prone to snapping.

Symptoms of a bad spacer include: 

• Misaligned or loose door walls and panels
• Cold air leakage around the door perimeter
• Difficulty closing doors completely flat
• Visible broken pieces inside door walls

This OEM Whirlpool replacement spacer restores critical door insulation integrity. Its durable construction supports tight door seals to maintain interior climate control.

Replace yours if any issues arise. This part is also compatible with some GE, Crosley, and select Kenmore side-by-side models. Reliable seal performance relies on an OEM spacer replacement when failing.

The Ice Maker Assembly is an OEM part for Whirlpool refrigerators, designed to replace your fridge's original ice-making unit. This assembly is responsible for ensuring a consistent and reliable supply of ice, featuring components such as the ice mold, the water inlet valve, and the ice ejector arms. 

Causes for a malfunctioning Ice Maker Assembly can range from mineral build-up in the water filter or inlet valve, to mechanical failures in the motor or electrical components. 

Symptoms of a bad Ice Maker Assembly include:

• Failure to produce ice
• Producing smaller or misshapen ice cubes
• Leaking water inside the freezer compartment
• Noisy operation or strange sounds during the ice-making process

This genuine Whirlpool OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: IF ICEMAKER IS NOT COMPATIBLE WITH UNIT ORDER ICEMAKER KIT PART# W10882923 IT COMES WITH ALTERNATE MODULE COVER AND HARNESSES PER MELODY AT WHIRLPOOL PARTS

This impinger assembly directs heated airflow inside the oven/microwave cavity to help promote even cooking and consistent heating. It replaces a damaged or warped air baffle to restore proper airflow distribution. What it does:

• Routes and evens airflow across the cooking cavity to help reduce cold spots
• Helps maintain consistent internal temperatures during operation
• Prevents hot air from short-circuiting around food for more uniform results
• Replaces cracked, warped, or missing air-baffle components that impair airflow

• Disconnect power to the appliance before starting any repair
• Use appropriate hand tools and take care to avoid sharp sheet-metal edges
• Inspect mounting clips/fasteners and replace if damaged; follow OEM fitment orientation

This is the mechanical shutoff arm for the ice maker. It lifts to pause ice production when the bin is full and lowers to resume, restoring proper on/off control to help prevent overfilling or a no-ice condition.

• Starts and stops ice production based on arm position (down = on, up = off)
• Replaces a bent, broken, or missing arm to restore proper shutoff function
• Helps address: ice maker won't stop making ice/overfills the bin
• Helps address: ice maker won't make ice because the arm is stuck in the up/off position

• Disconnect power to the refrigerator before servicing
• Remove the ice bin for access; withdraw the old arm from the pivot holes
• Insert the new arm into the ice maker pivot points; ensure smooth up/down movement
• Restore power and verify the arm raises to stop and lowers to start ice making

This is the small extension that attaches to the ice maker's shut-off arm. It lengthens the arm so the ice bin can reliably raise/lower the arm to stop ice production when full and resume when space is available.

• Extends the ice maker's shut-off/bail arm for proper bin detection
• Helps prevent ice maker overfilling when the bin is full
• Can resolve issues like continuous ice production, overfilling, or ice not stopping
• Restores original fit and function on compatible ice maker assemblies

• Disconnect power and shut off water supply before servicing
• Access the ice maker, then slide/clip the extension onto the shut-off arm as directed by your model's service info
• Ensure the arm moves freely and properly actuates the ice maker switch
• Restore power and verify the arm stops ice production when raised

This wire harness assembly routes power and signals between a range of appliance control and its components, restoring reliable electrical connections for proper operation. It replaces a damaged or worn harness to help eliminate intermittent or failed component function. What it does:

• Carries power and control signals between the control board and components
• Restores lost or intermittent electrical connections that can cause components to stop working
• Common symptom fixes: intermittent operation, components not powering on, or error conditions related to wiring
• Used where multiple connector plugs and bundled wires are required for safe operation

• Disconnect power (unplug or shut off breaker) before starting any repair
• Route harness along original wire paths and secure with existing clips or fasteners
• Match connector shapes and colors; ensure connectors are fully seated and latched

A single-pole, single-throw rocker switch that restores reliable on/off control for one electrical circuit. Replacing a worn or failed rocker switch helps return consistent control and stops intermittent or unresponsive operation. What it does:

• Opens and closes a single electrical circuit when the rocker is pressed.
• Common replacement for switches that stick, fail to latch, or cause intermittent power.
• Can stop symptoms such as unresponsive controls, lights or functions that won't turn on/off, or sparks from a worn switch.
• Matches OEM form and function for direct replacement in compatible appliances.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Note wire locations or take a photo before removing terminals to ensure correct reconnection.
• Use appropriate tools and avoid pulling on wires; if terminals are damaged, replace wiring or connectors.