Ikea Range / Cooktop / Oven Parts

This genuine replacement switch kit restores reliable electrical switching for your appliance's control or component circuit. Replacing a worn or failed switch helps bring back consistent on/off or mode selection response and prevents intermittent operation.

• Opens and closes the electrical circuit to control a function or component
• Helps resolve no response when actuating the switch or intermittent operation
• Useful when the switch sticks, feels loose, or shows signs of arcing or heat damage
• Can address issues like inability to turn a function on/off or erratic behavior

• Disconnect power and allow components to cool before servicing
• Photograph or label wiring to ensure correct reconnection
• Transfer any brackets or terminals from the old switch if applicable
• Secure connections firmly; avoid overtightening and verify proper operation after reassembly

Color: Stainless

This convection fan blade mounts to the fan motor and circulates hot air during convection cycles. Replacing a bent or damaged blade restores proper airflow, promoting more even temperatures and consistent baking and roasting performance.

• Mounts on the convection motor shaft to drive airflow through the oven cavity
• Helps maintain uniform temperatures for consistent convection baking/roasting
• Typical failure signs: rattling or scraping noises, visible wobble or damaged fins, weak airflow, or the fan not spinning freely
• A worn blade can contribute to uneven results in convection mode

• Disconnect power and allow the appliance to cool completely before servicing
• Access the blade behind the interior fan cover or rear panel (varies by model); note blade orientation and any spacers/washers for reassembly
• Handle sharp edges; avoid bending fins and ensure the blade spins freely without rubbing before restoring power
• For microwave/OTR convection units, high-voltage components are present.

This natural-gas orifice spud is sized for the 5K burner position on compatible gas cooktops and ranges. It meters gas to the burner to set proper flame height, helping restore consistent heat when the original orifice is clogged, damaged, or incorrect. What it does:

• Regulates gas flow for the designated burner; calibrated for the 5K position on natural gas systems
• Can help resolve weak or oversized flames, yellow/lazy flames, uneven heating, or intermittent ignition
• Required when converting back to natural gas on applicable units; not for LP gas
• Installs in the orifice holder/manifold beneath the burner head

• Shut off gas supply and power; allow the cooktop/range to cool completely
• Remove burner cap and head to access the orifice
• Use the correct nut driver; hand-start threads and tighten snugly—do not overtighten
• Reassemble, leak-check connections with soapy water, and verify flame quality per the service instructions

This blower moves air through your appliance to maintain proper cooling and ventilation. Replacing a worn or noisy blower restores airflow and helps protect internal components so the unit operates as designed. What it does

• Drives airflow through ducts or cooling channels to manage heat inside the appliance
• Helps expel heat and moisture or circulate cooling air, depending on the design
• Common symptoms of failure: fan won't run, weak/no airflow, loud rattling or squealing, burning smell, overheating or shutdown, or cooling/vent-related error messages

• Includes 1 blower

• Disconnect power before servicing; allow hot surfaces to cool
• Metal edges can be sharp—wear cut-resistant gloves and eye protection
• Note wire connections and mounting orientation; transfer any brackets or seals from the original unit if required
• After installation, confirm unobstructed airflow and correct blower orientation before fully reassembly and testing

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

This charcoal filter is used in recirculating range hoods to reduce cooking odors and smoke. Replacing a saturated filter restores ventilation performance and helps keep kitchen air fresher when venting air back into the room. What it does:

• Adsorbs cooking odors and vapors when the hood is set to recirculate indoors
• Helps maintain proper airflow and capture smoke/steam during cooking
• Replace if saturated, damaged, or shedding carbon
• Common signs: lingering odors, reduced airflow, discoloration, or loose carbon granules

• 1 charcoal filter

• Disconnect power to the hood before servicing
• Remove/open the filter cover or grille; release the old filter from its clips or frame
• Insert the new filter with proper orientation; secure it and reinstall the cover
• Charcoal filters are not washable or reusable; replace periodically as needed

The Bake Element is an OEM part for Whirlpool ranges. As a heating component, this bake element is responsible for providing bottom heat during baking and roasting functions.

Causes of a bad bake element include deterioration of insulated coils and connections from continual heat cycling. Exposure to drips or spatters can damage their integrity over time.

Symptoms of a bad bake element include:

• Inability to heat up to desired cooking temperatures
• Slow or ineffective baking and roasting results
• Error codes or failure alarms from the control board
• Visible burnouts or breaks in the coil filaments

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This oven bake burner is designed for Direct Spark Ignition (DSI) ranges. It channels gas from the bake orifice and distributes an even flame under the oven floor for consistent baking performance and reliable light-off during the bake cycle.

• Distributes gas through burner ports to create an even bake flame
• Works with the DSI spark electrode to ignite the bake flame
• Can address uneven or weak flame patterns and delayed ignition in bake

• Disconnect power and shut off gas; allow the oven to cool completely
• Remove the oven bottom and flame spreader to access the burner
• Transfer any reusable mounting hardware or shields from the original burner
• After reassembly, restore gas/power and leak-test any disturbed gas connections per local code

This replacement switch restores reliable control of a selected function by opening or closing an electrical circuit inside your appliance. When the original switch wears out, buttons may stop responding or features may not activate consistently.

• Opens/closes an electrical circuit when the button/actuator is engaged
• Routes power or sends a signal to the control or component
• Common symptoms: no response when pressed, intermittent operation, or function won't start
• May show signs of heat damage, loose terminals, or inconsistent "click" feel

• Disconnect power at the breaker before servicing
• Photograph or label wire positions to ensure correct transfer to the new switch
• Move wires one at a time; fully seat connectors on the correct terminals
• Reassemble, restore power, and test the function activated by the switch

The Range Glass Assembly is an OEM part for Frigidaire ranges. It covers the inner cooking cavity, protecting both the occupant and the heating elements and mechanisms inside. The glass assembly also allows for viewing into the oven to check on food without needing to open the door each time. 

Symptoms of a bad glass assembly include:

• Cracks or breaks in the glass
• Difficulty viewing into the oven cavity 
• Leaks around the glass seal
• The glass popping out of place

Causes of a bad glass assembly can be wear and tear over time, exposure to excessive heat, or damage from impacts. 

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement surface burner head for gas ranges/cooktops channels fuel from the orifice into a controlled flame ring. Replace a worn or clogged head to restore reliable ignition, even flame distribution, and consistent heat control.

• Distributes gas through precision ports to create an even flame ring
• Works with the spark igniter/electrode for dependable lighting
• Supports the burner cap and stabilizes the cooking flame
• Common symptoms of a bad/clogged head: weak or uneven flames, yellow tipping, delayed ignition, or clicking without lighting

• Disconnect power and shut off gas; allow the appliance to cool before servicing
• Remove grate and burner cap; if your model uses mounting screws, remove them and lift off the old head
• Clean the orifice holder area; ensure burner ports are clear before installation
• Align the new head with the orifice and igniter, reinstall hardware and cap, then test for proper ignition and an even flame

This light transformer (20VA) steps down incoming voltage for the appliance's light circuit. Replace a failing transformer to restore dependable illumination so you can monitor cooking progress and see clearly when cleaning.

• Steps down line voltage to the lower voltage used by the light circuit
• Supports consistent, reliable interior lighting
• A failed transformer can leave the light inoperative even with a good bulb
• Intermittent operation or flickering can indicate a weakening transformer

• Disconnect power at the breaker or unplug the unit before servicing
• Access and mounting location vary by model; note wiring and orientation before removal
• Move wires one at a time to the matching terminals/leads on the new transformer
• Secure the transformer and route wiring away from hot or moving parts; test light operation before reassembly

This orifice spud meters gas to a burner on your range or cooktop, setting proper flame size for efficient, even heating. Replacing a damaged or incorrect spud restores consistent burner performance and flame quality.

• Meters gas flow through the burner orifice to control flame height and shape
• Supports efficient combustion and consistent heat output
• Common fix for flames that are too high/low, yellow/sooty, or uneven
• Used when setting up or converting a model for the specified fuel type (LP or natural), per the position of each burner

• Shut off the gas supply and disconnect electrical power before servicing
• Remove the burner cap and head to access the spud; lift the cooktop or open the range top if required
• Remove/install with a properly sized wrench; do not overtighten. Apply thread sealant only if specified by the manufacturer
• Match each spud to the correct burner and fuel type per your model documentation; after reassembly, restore gas and leak-test with a soapy-water solution

This LP conversion kit adapts select gas cooking appliances to operate on liquid propane. Use it when installing a natural-gas model on an LP supply to ensure proper ignition, flame characteristics, and safe performance. What it does

• Converts a natural-gas appliance for use with LP/propane per the model's installation instructions
• Provides correctly sized LP components to achieve proper flame size and combustion
• Helps prevent issues such as yellow flames, sooting, and poor simmer control caused by incorrect gas type
• Required when installing where only propane is available; model-specific kit

• One LP conversion kit

• Conversion must be performed by a qualified gas technician; follow all local codes
• Shut off gas and electrical power and allow all components to cool before servicing
• Replace the specified parts and set the pressure regulator for LP; adjust low flames/air shutters as directed in the service/installation manual
• Leak-test all connections and apply conversion labels after completion; verify flame quality

The Relay Board is an OEM part for Frigidaire ranges. It is an electronic component that controls the operation of various range functions and components by directing electrical currents through a network of relays.

Causes of a bad relay board include failure of electronic components over time due to continuous use, component fatigue, water damage, or surges/spikes in electrical current.

Symptoms of a bad range relay board include:

• Inoperable or unreliable oven/range functions such as bake, broil, warm, etc.
• Issues with cooktop burner ignition or flame level control
• Inconsistent or inaccurate temperature readings
• Error codes or diagnostic trouble codes appearing

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.