Parts for Lg LUTD4919SN/00: Introduction Parts

Replace a gas range burner when flames are uneven, won't ignite, or produce yellow flames. Direct swap installation takes 10-15 minutes with basic tools.

Burner not heating or heating unevenly? This surface element restores full heat output on your range. Straightforward DIY fix in under an hour.

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

Protective insulator cushion for ranges. Installs between components to dampen vibration and prevent rubbing. Replace if cracked, worn, or missing.

Insulator pad for electric and gas ranges. Protects components from heat damage. Replace if cracked, deteriorated, or missing to maintain proper insulation.

Range insulator cushions components, reduces vibration, and prevents heat transfer. Restores proper spacing when original insulator wears or fails.

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

Replacement screw for securing panels, brackets, and internal components. Restores tight fit and proper alignment when original hardware is stripped or missing.

This ring assembly includes the wheel hub and bearing components used in the range to support smooth rotational movement of certain internal parts. It helps ensure even, stable operation of rolling or spinning mechanisms within the appliance. Replace this assembly if you notice grinding noises, uneven movement, or visible wear on the wheel or bearing surfaces.

A factory screw for securing specified components in your appliance. Replaces a missing or damaged fastener to restore a tight, reliable hold and help reduce vibration, rattling, and misalignment.

• Secures brackets, covers, or internal assemblies where this exact screw is specified by the manufacturer
• Useful when the original screw is missing, stripped, or corroded
• Helps eliminate looseness, vibration, and rattling noises
• Matches the original fastener for proper fit and thread engagement

• Disconnect power (and shut off water supply if applicable) before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged clips or inserts to ensure a secure repair

Secures panels, brackets, and internal components in your range. Replace this screw if the original is missing, stripped, or rusted for proper fit.

This customized screw secures appliance components where a standard fastener won't fit, helping keep panels, brackets and small assemblies stable. It's a direct-fit replacement when the original specialized screw is missing or damaged. What it does:

• Fastens and holds appliance panels, brackets or small parts in place
• Prevents rattling, loose trim or misaligned components caused by a missing or stripped screw
• Matches the OEM fit and thread pattern for proper engagement and alignment
• Used in locations that require a non-standard or customized fastener

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can strip threads or crack parts
• Keep removed hardware organized so you can reinstall in the original location

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

This is a replacement customized screw designed to secure appliance panels and components. It restores proper fit and fastening where the original screw is lost or worn, helping maintain safe, stable operation. What it does

• Replaces missing or damaged mounting screw used on appliance panels and internal components
• Restores secure fastening to reduce vibration and rattling during operation
• Matches the original OEM fit and thread form for correct engagement when verified for your model
• Helps prevent loose parts that can cause noise or interfere with moving components

• Disconnect power and water before servicing the appliance
• Verify screw size, thread direction, and length match the original before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid overtightening to prevent stripping or damaging mating threads

Control knob assembly for gas ranges. Mounts on the control panel to operate burners. Replace if your knob is cracked, broken, loose, or missing.

Replace a cracked, stripped, faded, or missing control knob on your electric range. This knob assembly installs on the control panel for secure turning.

If your range won't heat, displays error codes, or has unresponsive controls, the power control board may have failed. Moderate difficulty repair.

Fix a range that won't heat, cycle on, or respond to buttons. This control board assembly interprets inputs and restores reliable oven operation.

Fix an unresponsive oven control knob or broken control dial. This encoder board detects knob position and sends signals to adjust temperature settings.

Replacement screw for electric and gas ranges. Secures panels, brackets, and internal assemblies. Restores tight fit when original is missing or stripped.

Factory-style screw for securing panels, brackets, and assemblies on gas ranges and cooktops. Replace if missing, stripped, or damaged during repairs.

Replace a faulty gas range burner nozzle if flames are uneven, yellow, or won't ignite properly. This part meters fuel flow to each burner for balanced heating.

Replace a faulty range power control board when your oven won't heat, display is blank, or controls are unresponsive. Restores full functionality.

Fix a range that won't heat, displays error codes, or has unresponsive controls. This main control board manages power distribution and system logic.

Replace your range's outer door trim to restore a finished appearance and maintain proper door seal alignment. Direct-fit frame for compatible models.

This is the inner glass panel that sits on the inside of the oven door, forming part of the insulated door assembly. It helps retain heat inside the oven cavity and protects the outer door glass from direct exposure to high temperatures. Replace this glass if it is cracked, shattered, or has visible damage that could compromise oven heat retention or safety.

This air guide directs cooled air inside the refrigerator compartment to help maintain even airflow and temperature distribution. Replaces a damaged or missing guide to restore proper venting and help reduce uneven cooling. What it does

• Channels cold air from the evaporator vent into the fresh food compartment for more consistent cooling.
• Helps reduce warm spots or uneven temperatures near shelves and door bins.
• Prevents direct airflow onto stored items, protecting sensitive foods from frost or drying.
• Fits behind vents or above crisper drawers to guide airflow where needed.

• One (1) air guide

• Always unplug the appliance or switch off power at the breaker before servicing.
• Typically installs without specialty tools; you may need to remove shelves or drawers for access.
• Handle plastic parts carefully to avoid cracking; align tabs and snap into place until secure.
• If airflow issues persist after replacement, check vents, damper, and evaporator fan for related faults.

Clear viewing pane for range oven doors. Replace when cracked, shattered, chipped, or stained to restore visibility and a clean, finished appearance.

Inner door cover panel for electric and gas ranges. Replace this part if your existing panel is cracked, broken, damaged, or missing from the oven door.

Bracket that anchors the handle to your range oven door. Replace if cracked, stripped, or broken to restore secure handle attachment and alignment.

Replacement door frame for electric and gas range ovens. Replace this structural component if cracked, bent, or damaged to restore door appearance.

Decorative panel for your range oven door. Installs on the exterior door surface to refresh appearance. Replace if cracked, chipped, or discolored.

The inner cover protects internal components and wiring by covering the appliance's cabinet opening, helping prevent debris entry and accidental contact. It restores safe access and maintains the appliance's internal layout and airflow. What it does

• Shields internal electronics, wiring and assemblies from dust and debris
• Helps prevent accidental contact with energized components
• Restores proper internal clearance and part alignment after repair
• Can address symptoms like visible damage, exposed wiring, burning odor or intermittent operation caused by a compromised cover

• Replace with power disconnected and appliance unplugged to avoid shock
• Verify correct orientation and secure all mounting tabs/screws; do not force into place
• Inspect adjacent wiring and components for damage while the cover is removed
• Use only the part number shown for exact fit

This hinge assembly secures and guides a refrigerator/freezer door so it opens, closes and stays properly aligned. Replacing a worn or damaged hinge restores smooth movement and helps maintain a tight door seal. What it does:

• Provides the pivot point and mounting for a refrigerator/freezer door
• Prevents door sag, misalignment, and uneven gaps that can affect sealing
• Restores smooth opening and closing when original hinge is worn or bent
• Helps reduce stress on cabinet and door hardware caused by loose or damaged hinges

• Disconnect power and empty food from the door area before starting; support the door to prevent dropping.
• Basic hand tools typically required; follow OEM instructions for correct fastener torque and alignment.
• Verify left/right and top/bottom orientation before installation; hinges can be location-specific.

Shield plate for electric and gas ranges. Protects internal components from heat and debris. Replace if cracked, bent, damaged, or missing for proper range operation.

Protects your range control panel display from spills, grease, and damage. Replace when cracked, discolored, or visibility is reduced. Verify fit with your model.

Fix unresponsive controls or erratic range operation. This main power control board restores reliable feature control and stable performance.

Fix unresponsive or intermittent range controls with this controller assembly. Restores electronic functions and signals for proper appliance operation.

Plastic supporter stem that fits between the control knob and encoder board on your range. Replace if broken, cracked, or jamming the control switch.

Replaces a worn, cracked, or missing range control knob. Restores grip and indicator pointer for selecting heat settings and safe operation.

Wire harness for gas ranges. Connects electrical components inside your range. Replace if wires are frayed, damaged, or connections are loose or broken.

If your range control panel is loose or cooking functions are erratic, the PCB supporter may be cracked. This mounting bracket secures the circuit board.

Fix an oven door that won't stay open or slams shut with this range door spring. Simple DIY repair requiring only a Phillips screwdriver, 30 minutes.

The Module Display PCB Assembly is an OEM component specifically designed for LG dishwashers. Housed within the electronic control panel, this printed circuit board routes signals between control buttons and the dishwasher module. Integrated circuits process commands to start cycles and display settings through LED indicators. 

Causes of a bad module display PCB can include water damage into circuit paths, voltage fluctuations over time, or loose connections. Without a functioning interface, users are unable to select wash cycles or check cycle status.

Symptoms of a bad module display PCB include:

• Blank or unresponsive control panel 
• Inoperable buttons and dials
• Erratic lights and buzzers during cycles
• Diagnostic error codes shown

This LG OEM replacement restores dependable controls. Compatible also with Kenmore Elite dishwasher models, it provides a direct fit and easy restoration of washing functions. Proper installation protects future operations while maintaining convenience.

This is a circular wire harness holder that secures and organizes internal wiring within the range. It clips onto the frame or mounting points to keep wires routed properly and away from heat sources. Replace this part if it is broken or missing, which can cause loose wiring or potential contact with hot surfaces.

Protective cover that installs over the power cord connection on your electric range. Replace if cracked, broken, or missing to restore appearance.

Directs heat and light inside the oven cavity for even browning and proper illumination. Replace if damaged or warped to restore cooking consistency.

Idle packing bushing for electric and gas ranges. Replaces worn, cracked, or missing bushings. Ensures proper fit and cushioning for range components.

Oven not heating evenly or at all? The carbon heater element radiates consistent heat throughout the oven cavity. Moderate DIY repair with guidance.

Fix loose or noisy heating elements with this heater mounting bracket. Secures the heater assembly in proper position to restore quiet, stable operation.

Replace a bent or missing heater mounting bracket to prevent sagging heating elements, uneven heating, and potential contact damage in your range.

This heater cover protects the dryer heater assembly and helps direct airflow for efficient operation. Replacing a damaged cover restores proper heater protection and reduces the risk of airflow restriction or overheating. What it does:

• Shields the heating element and internal wiring from debris and lint buildup
• Helps channel hot air through the drum and vent path for consistent drying
• Prevents direct contact with the heater, improving safety
• Addresses symptoms like excessive lint accumulation, rattling near the heater area, or minor airflow issues

• One heater cover

• Disconnect power to the appliance before starting any repairs
• Typical install requires removing the dryer cabinet or access panel; follow OEM instructions
• Inspect surrounding components (heater, element housing, mounting clips) and replace any damaged fasteners

This glass shelf provides a stable, easy-to-clean surface for organizing groceries inside your refrigerator. It replaces a cracked, chipped or missing shelf to restore usable storage space and keep items level. What it does:

• Supports food containers, produce bins and small appliances inside the fridge
• Restores a flat, even surface when an old shelf is cracked or warped
• Helps prevent spills by providing a solid, easy-to-wipe surface
• Fits into existing shelf tracks or ledges to stay securely in place

• Remove all items from the shelf area before replacing; lift straight up to disengage from shelf tracks
• Handle the glass with care and wear gloves to avoid cuts
• Clean shelf tracks and surrounding area before installing the new shelf

Seals the oven door to contain heat and maintain proper cooking temperatures. Replace if torn, cracked, or no longer creates a tight seal. Confirm fit with your model number before ordering.

Fix uneven flames or burner not lighting with this gas range burner tube. Direct replacement for standard slide-in and freestanding models.

Grille assembly for gas ranges. Installs on the front of the appliance. Replace if your original grille is cracked, broken, warped, or missing.

Gas burner orifice nozzle for ranges and cooktops. Installs inside the burner box to meter gas flow. Replace if damaged, missing, or converting fuel type.

Fix weak flames or burners that won't light properly with this gas burner nozzle. Controls gas flow for proper flame size. Simple install with basic tools.

Gas burner orifice nozzle for ranges and cooktops. Installs inside the burner box to meter gas flow. Replace if damaged, missing, or converting fuel type.

Fix weak flames or burners that won't light properly with this gas range burner nozzle. Controls gas flow for optimal flame performance. DIY install.

Fixes burners that won't light or ignite properly on your gas range. This gas valve assembly controls gas flow to surface burners. Moderate DIY repair.

Fix burners or oven not lighting with this gas valve assembly. Controls gas flow to restore safe ignition and consistent heating in your range.

Gas range won't ignite or heat properly? This valve assembly controls gas flow to your oven and burners. Restores ignition and safe operation.

Controls gas flow to your range burner. Replace this valve assembly when the original is faulty, leaking, or damaged to restore safe gas regulation.

This is a gas surface burner head rated at 18,500 BTU that sits atop the burner base on a range cooktop. It distributes gas evenly to produce a consistent flame for cooking. Replace this burner head if you notice uneven flames, yellow or weak flame output, difficulty igniting, or visible damage such as clogged or corroded gas ports.

Burner cap for gas ranges. Fits over the burner assembly to protect from debris and damage. Replace if cracked, chipped, or missing for proper operation.

Replace a cracked or damaged burner cap causing uneven flames or yellow/orange fire. This cap sits atop the burner element to distribute heat evenly.

Protective cover that fits over the burner head on your gas range cooktop. Replace if cracked, chipped, broken, or missing to restore appearance.

Uneven flame or poor heating? This gas range burner cap directs flames evenly across cookware and contains sparks. Simple snap-on installation.

Fix intermittent power issues or control failures with this range main wiring harness. Connects electrical components for proper signal communication.

Cable assembly for gas ranges. Replaces worn, damaged, or broken cable connections inside your range. Essential structural component for proper operation.

Fix control issues or power failures with this gas range cable assembly. Restores reliable operation when wiring is damaged, burned, or has loose connections.

Fixes unresponsive controls or features not working on your gas range. This cable assembly restores power and signal connections between components.

Fix burners that won't light or controls that don't respond with this range wire harness. Restores electrical connections between components. Moderate DIY.

Fix unresponsive control panel buttons with this tactile switch replacement. Restores reliable button response. Simple DIY repair, typically under 5 minutes.

Microwave won't turn on or has no power? A failed thermostat often causes complete power loss. Moderate DIY repair requires disassembly to access.

Replace your range's wire harness if the existing wiring is damaged, frayed, or showing signs of wear. Connects electrical components inside your range.

The Magnetron Thermostat is an OEM part for LG microwaves and built-in ranges. Its primary function is to monitor the temperature and ensure that it remains within a safe operating range. If the temperature exceeds the preset limit, the thermostat will interrupt the power supply to the magnetron, preventing overheating and potential damage.

Causes of a faulty magnetron thermostat can include electrical malfunctions, component failures, or physical damage. These factors can result in issues such as erratic heating, microwave not heating properly, or the appliance shutting off unexpectedly.

Symptoms of a bad magnetron thermostat may include:

• Microwave not heating food evenly or at all
• Inconsistent or weak heating performance
• Microwave shutting off or displaying error codes related to temperature issues

This OEM LG part can also be used on Kenmore/Sears appliances. 

If your oven won't reach the right temperature or shows an F9 error, the temperature sensor may be faulty. Simple DIY repair in under 45 minutes.

Replace a damaged or corroded wire harness in your range. This single-connection harness restores proper electrical connections when original wiring is frayed, melted, or broken.

Fix uneven cooking or baking in your range. This convection fan motor circulates hot air for consistent heat distribution. Moderate DIY repair.

Secures the control panel to your range cabinet. Replace if the bracket is cracked, bent, stripped, or hardware no longer holds the console firmly in place.

Fix inaccurate oven temperatures with this range temperature sensor. Restores proper heating cycles when your oven runs too hot or cold.

Motor loose or vibrating excessively? This motor bracket secures the motor to the chassis, reducing vibration and maintaining alignment for quieter operation.

Fix loose or misaligned range components with this retaining ring. Secures parts in place to prevent excess movement and wear. Simple installation.

Fixes uneven baking and longer cooking times in your range. This convection fan blade restores proper air circulation for consistent oven temperatures.

This Fan Blade is an OEM part for LG microwaves. It is a critical component designed to circulate air within the microwave, aiding in heat dissipation and ensuring even cooking. 

Fan blades in microwaves can suffer from wear, imbalance, or damage due to regular use or accumulation of debris. A malfunctioning fan blade can lead to inadequate ventilation, affecting the microwave's cooking efficiency and potentially causing overheating.

Symptoms of a bad fan blade include:

• Unusual noises during operation, such as rattling or buzzing, indicate a loose or damaged blade.
• The microwave overheating or shutting off prematurely.
• Inconsistent cooking or hot spots in food suggest poor air circulation.
• The fan not starting, or stopping unexpectedly during use.
• Visible signs of damage or wear on the blade.

This OEM LG part is also compatible with some Sears/Kenmore models.
 

Replace your damaged or broken range handle bar. This bar installs on the oven door, providing a secure grip for opening and closing. Order now.

Fix a humming or stalled range component with this AC synchronous motor assembly. Restores proper rotation when the motor fails to turn or makes noise.

Range heating element loose or misaligned? This heater mounting bracket secures your heating assembly to the cabinet for stable, reliable operation.

This is the exterior side panel that attaches to the body of the range. It provides structural support and a finished appearance to the side of the appliance. Replace this panel if it is dented, scratched, rusted, or damaged during installation or use.

Replace your burned-out or dim oven light bulb to restore interior visibility while cooking. Direct-fit incandescent lamp for safe food monitoring. Verify fit with your model number.

The range packing seal creates an airtight barrier around oven doors or other range components to maintain proper cooking temperatures and prevent heat loss. Positioned around door edges or component joints, it needs replacement if heat escapes, cooking becomes uneven, or the seal appears cracked or compressed.

Oven not heating or heating unevenly? This electric range heating element restores proper cooking temperatures. Moderate DIY difficulty, 30-45 minutes.

Fix uneven oven temperature or burner control issues with this range governor assembly. Regulates gas flow for consistent heating. Moderate DIY repair.

Base plate for electric and gas ranges. Provides structural support at the bottom of the appliance. Replace if cracked, broken, or missing. Easy install.

Replace a damaged or non-heating range burner assembly. This part restores proper heat distribution when burners fail to ignite or heat unevenly. DIY repair.

Rubber foot pad that supports and stabilizes your range on the floor. Replace if cracked, broken, worn, or missing to keep your appliance level.

Idle bracket for electric and gas ranges. Secures internal components in place. Replace if bracket is bent, cracked, broken, or missing during repair.

Mounting anchor for range door handles. Replaces worn, broken, or missing anchors to restore secure handle attachment and eliminate wobbling or loose fit.

The LP Conversion Kit is an OEM part for LG gas ranges, allowing safe conversion between natural gas and liquid propane fuel sources. It features necessary valve bodies and tubing to appropriately meter gas flow.  

Causes of failure involve worn or corroded tubing restricting gas volumes over time, stripped injector threads inhibiting secure connections, or damaged valves losing precise metering accuracy.

Symptoms of a bad LP conversion kit include:

• Improper flame levels unable to heat cooktop/oven  
• Gas smell signaling unsafe leaks at connections
• Incorrect fuel/air ratios affecting efficiency and safety
• Non-functioning burners from blocked or disconnected lines

Replace yours today with this genuine OEM LG kit. Certified components uphold performance standards across Whirlpool, Frigidaire, and Kenmore gas models as well by mitigating combustion risks. 

Accessory assembly for electric and gas ranges and wall ovens. Replaces damaged, broken, or missing accessory components. Restores proper fit and function.