Jade Dishwasher Parts

Dishwasher rack mounting strip roller.

Restore safe, smooth door operation with this dishwasher door spring. It counterbalances the door's weight so it opens and closes in a controlled way, preventing a sudden drop when the original spring breaks or fatigues.

• Provides the tension that counterbalances the dishwasher door through the hinge mechanism
• Helps prevent the door from slamming open or feeling unusually heavy
• Restores smooth, even door movement side-to-side
• Typical symptoms: door drops quickly, feels heavier than normal, uneven motion, or a visibly broken/stretched spring

• Disconnect power and shut off water before servicing
• Remove the toe/kick panel to access the hinge area
• Support the door, then move it slightly to relieve tension before unhooking the old spring
• Attach the new spring between the frame anchor and hinge arm; if your model uses two springs, replace both sides for even tension

Color: light gray. Measures about a 1/2 inch high by 4 inches deep.

This dishwasher door seal fits into the tub channel to create a tight, water-resistant barrier when the door closes. Replacing a worn gasket helps stop nuisance leaks and restores proper door compression and moisture containment.

• Creates the primary seal around the dishwasher tub opening when the door is closed
• Helps keep wash water, suds, and steam inside the wash cavity
• Wear can lead to drips at the front corners or along the sides
• Replace if the gasket is cracked, torn, flattened, or no longer sealing; the door may be harder to latch

• Disconnect power and turn off the water supply before servicing
• Remove the old gasket and thoroughly clean the channel of debris and residue
• Warm and relax the new gasket; start at the top center and press evenly into the channel without stretching
• Close the door for several hours to help the seal set; run a test cycle and check for leaks

This electronic control board kit is the appliance's central controller, coordinating inputs and powering key components. Replacing a failed board restores proper operation, responsive controls, and reliable cycle management. What it does:

• Manages timing and power to motors, valves, heaters, fans, and other loads
• Interprets sensor and user-interface signals to start, run, and end cycles correctly
• Common failure signs: dead or unresponsive controls, cycles that won't start/finish, repeated error codes, or intermittent operation
• Helps address issues caused by power surges or board damage

• 1 electronic control board (module)

• Disconnect electrical power to the appliance; turn off gas/water if applicable
• Use ESD protection and handle the board by its edges
• Photograph wiring; transfer connectors one at a time and match any jumpers/DIP-switch settings from the original board
• Restore power and perform any model-specific tests or programming per OEM instructions

This dishwasher impeller assembly mounts on the circulation pump and pressurizes wash water for the spray arms. Replacing a worn or damaged impeller restores proper spray pressure, cleaning performance, and quieter operation.

• Spins with the circulation motor to pressurize wash water
• Drives flow to the spray arms for effective wash action
• Typical symptoms: weak or no spray, poor cleaning results, grinding or rattling from pump area
• Often fails from broken vanes or debris; inspect filters/chopper while open

• Disconnect power and water before servicing
• Access is typically from inside the tub: remove the lower spray arm, filter screens, and cover to reach the impeller
• Note the order of parts and transfer any reusable hardware; replace worn O-rings/seals as needed
• Do not overtighten plastic parts; verify the impeller spins freely before reassembly and testing

Lower wash arm redirects pressurized water across the dishwasher's lower rack to rinse and remove food and residue, restoring intended wash coverage and improving cleaning performance. What it does:

• Directs jets of water through multiple spray holes to rinse dishes on the lower rack.
• Helps remove stuck-on food, film and spotting on plates, bowls and cookware.
• Replaces cracked, clogged or broken lower spray arms that can cause poor cleaning or leftover residue.
• Works with the dishwasher's pump flow to maintain proper spray pattern across the lower rack.

• Refer to your model's parts diagram and instructions; the arm commonly snaps or threads onto the lower spray arm mount and procedures vary by model.
• Always disconnect power to the dishwasher before servicing; follow basic safety precautions.
• Clean the filter and any debris from spray holes before installing to avoid re-clogging.
• Inspect the mounting clip or retaining nut when removing the old arm and replace if damaged.

This dishwasher drain hose channels wastewater from the pump to your home drain or air gap. Replacing a cracked, kinked, or clogged hose restores proper draining performance and helps prevent leaks or water backing into the tub. What it does:

• Routes wastewater from the dishwasher to the household drain or air gap
• A damaged, kinked, or blocked hose can cause slow/no drain, standing water, or leaks
• Visible splits, soft spots, or persistent odors/backflow are common signs the hose should be replaced
• Restores reliable draining and helps protect surrounding cabinets and flooring from water damage

• 1 drain hose

• Disconnect power and shut off water before servicing
• Pull the dishwasher forward and place a towel or pan to catch residual water
• Match the original routing and maintain a proper high loop or air gap per local code to prevent backflow
• Secure connections with clamps, ensure the hose isn't kinked, and run a test cycle to check for leaks

The Lower Washarm is an OEM replacement part for Whirlpool dishwashers. Positioned at the bottom of the dishwasher tub, it rotates during the wash cycle, distributing water and detergent evenly across the lower rack. 

Over time, wash arms can become clogged with food debris or mineral deposits, reducing water flow. Physical damage such as cracks or warping can also impede the wash arm's rotation and affect its cleaning performance.

Color: Gray

Symptoms of a faulty lower wash arm include:

• Inadequate cleaning of dishes on the lower rack
• Uneven or inconsistent water spray
• Clogged or obstructed spray nozzles
• The arm not spinning or rotating correctly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This roller fits the cable bracket assembly and helps guide the cable smoothly to reduce binding and wear. It restores proper cable tracking so the mechanism moves more quietly and reliably. What it does:

• Guides and supports the cable within the bracket so the cable runs true
• Reduces rubbing, binding, and premature cable wear
• Helps eliminate squeaks or grinding where the cable contacts the bracket
• Restores smoother operation of the affected door/assembly movement

• One roller for the cable bracket (quantity: 1)

• Disconnect power before starting any repair and follow all safety guidelines
• Requires basic hand tools; access the bracket per your model's service instructions
• Inspect the cable and bracket for wear or damage and replace if necessary
• Test operation after installation to ensure proper cable routing and smooth movement

Color: Gray

Color: Gray

This upper wash arm directs rotating spray to the dishwasher's top rack to help improve cleaning coverage and reduce food/residue on upper-rack dishes. Fits as the rotating upper spray arm assembly for compatible dishwashers. What it does:

• Rotates and sprays water across the upper rack to help remove stuck-on food and rinse dishes.
• Helps correct weak or uneven spray patterns from the top rack.
• Can reduce spotting and areas that remain soiled when the upper arm is damaged or clogged.
• Replaces a worn, cracked, or clogged upper spray arm to restore proper spray action.

• Always disconnect power to the dishwasher and turn off the water supply before servicing.
• Remove the upper rack to access the arm; unclip or unscrew the old arm and install the replacement until it seats/threads securely.
• Clear any debris from the mounting area and ensure the arm spins freely before running a test cycle.
• Run a short rinse or quick cycle to verify correct spray pattern and fit.

This chopper assembly replaces the food-chopping component in compatible countertop food processors, restoring even chopping and diced results. It helps get blades turning and keeps food processing performing as intended. What it does:

• Spins and chops food inside the processor bowl for consistent results
• Restores proper cutting when chopping is uneven or not happening
• Helps eliminate food buildup that causes noisy or inefficient operation
• Works with the existing drive coupling to transfer motor power to the blades

• Disconnect power and remove the processor bowl and lid before servicing
• Handle blades carefully — they are sharp; wear cut-resistant gloves
• Ensure the part seats fully on the drive coupling and locks into place before use
• Test operation with small amounts of food after reassembly; stop immediately if unusual noise or resistance occurs

This snap-in outlet connector secures wiring to an appliance control or harness and restores a reliable electrical contact. Designed for a direct, tool-assisted snap fit, it helps eliminate loose or intermittent connections. What it does:

• Provides a secure snap-in electrical connection between wiring and the appliance harness or control
• Restores power flow when a worn or damaged outlet causes intermittent operation or no power
• Prevents arcing and poor contact that can result from loose terminals
• Matches OEM fit for straightforward replacement when the original snap outlet is broken or missing

• Disconnect power to the appliance before inspecting or replacing electrical parts
• Remove access panels as required to reach the outlet; replacement typically snaps into place
• Verify correct orientation and full seating of the connector to ensure a solid contact
• If corrosion or wiring damage is present, replace or repair wiring per OEM guidance

Color white. The wash arm measures about 11 inches, and the retainer about 3 inches.