Need Help?
Call
Replacement control knob for range surface burners. Attaches to the infinite switch to adjust heat settings. Replace cracked, broken, or missing knobs.
Ordered knew hinge. watched your video and took about 20 mins to fixed. got the part very fast o once again. thanks. Read more
Color: White. Measures about a little over 2 inches in diameter. For black order WP74011287.
Replaced Read more
Replacement control knob for your range cooktop. Installs on the control shaft to restore precise burner selection. Needed when original is cracked, broken, or missing.
I ordered new knobs with lettering on them. AppliancePartsPros.com enabled me to order the correct knobs by putting in the model number of the stove and by showing closeup pictures of the front and back of the knobs. For example, one out the the 4 knobs was for the simmer burner. I was given this information and that knob has "simmer" on it while the other 3 don't. On the down side the burner knobs cost nearly $100 to replace. I am hoping that their quality is such that they will last a... Read more
Replacement control knob for cooktop burner valve shaft. Needed when original knob is cracked, broken, missing, or markings are worn and illegible.
Ordered part from Appliance Parts Pros.com. Removed old knob Replaced with new knob. Read more
Burner clicks but won't light? This spark electrode ignites the gas at your cooktop burner. Fixes worn or cracked electrodes causing ignition failure.
Replacement control panel touch pad for your range. Restores unresponsive buttons when keys stop registering, worn surface causes input failures, or panel is cracked.
After doing much research online, I found out that the Touchpad on the JennAir downdraft gas range JGS9900BDS is very prone to "breaking." All my neighbors who has this model has reported that the touchpad stopped responding after a few years. Replacing was fairly simple. 1. Turn off the electricity to the range at the breaker 2. Pull the range out by an inch or two 3. On each side of the control panel, remove the screws. 4. Open the oven door and remove the 4 hex screws under the control... Read more
Orifice holder assembly for gas cooktop burners. Secures the gas orifice in place on the burner valve. Replace if cracked, broken, or missing.
Connects your range to the wall outlet to supply electrical power. Replace if your original cord is frayed, damaged, cracked, or missing from installation.
Replace your range door gasket to restore a tight seal and prevent heat loss. Fits worn or cracked seals so your oven door closes properly. Confirm fit.
Burner won't light or clicks continuously? This gas range surface igniter creates the spark to ignite cooktop burners. Simple DIY repair.
If your gas range burner won't light or clicks continuously, this spark electrode creates the spark needed to ignite the gas. Simple repair restores ignition.
This spark ignition switch initiates the electrical spark that lights the gas burners on your range cooktop. It provides the timing and electrical signal needed for reliable burner ignition. Replace this switch if your burners won't light, have delayed ignition, or require multiple attempts to start.
White control knob for range. Replaces cracked, broken, or missing knobs on the control panel. Restores smooth selection of settings and functions.
Replaced the knob. It was one of those small projects that you keep forgetting to take care of. Luckily, I had the serial numbers for this Maytag product and was able to order from ApplianceParts Pros.com on line. The part was on a nation wide back order. Even though it was only a $15.00 part, AppliancePartsPros.com kept me up to date on my shipment and notified me when it was on its way. I will definitely use this company again and would recommend them to everyone. Read more
Bisque spacer that installs between range door handle and panel. Replace if cracked, broken, or missing to restore proper spacing and secure alignment.
1. Unscrew 5 screws, on the over door (2 on top, 3 on bottom). 2. Remove oven door cover 3. Insert screw, from the inside of the door cover 4. Add spacer between the outside door cover and handle 5. Tighten screw, until secure 6. Attached door cover with 5 screws Read more
Color: gray. Measures about 2 inches in diameter.
Very easy to change, just gently pull them off . Read more
Burner cap sits on top of the burner head to shape the flame and protect from spills. Replace if cracked, chipped, or missing to restore appearance.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.