Jenn-Air Cooktop Parts

The Surface Ignitor is an OEM part for Whirlpool ranges and cooktops. This component is responsible for generating the spark needed to ignite gas burners on the cooktop or oven pilot light.

Causes of a bad Surface Ignitor can include wear and tear over time due to repeated use during ignition. Physical damage is also possible.

Symptoms of a failed surface ignitor include:

• Inability to ignite any gas burners
• Repeated sparking sounds but no ignition
• Yellow burner flames instead of blue

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

A replacement switch/ignitor that restores spark ignition so gas burners or the oven will light reliably. Designed to replace a failed ignition switch and help recover consistent sparking for normal appliance operation. What it does:

• Sends the spark needed to ignite gas burners or the oven burner.
• Common symptom: burners or oven won't light or ignition clicks without sparking.
• Can fix intermittent ignition or complete loss of spark at the cooktop/oven.
• Works as the electrical switching/ignition component within the appliance's ignition circuit.

• Disconnect power and shut off the gas supply before beginning any work.
• Handle wires and terminals carefully; avoid bending or damaging the igniter wiring.

This pressure regulator controls incoming water pressure to the appliance's water/ice system, helping maintain steady flow for proper dispenser and ice maker operation. Replaces a worn or failing regulator to restore correct water delivery. What it does:

• Reduces and stabilizes incoming household water pressure for the appliance's water valve/ice maker
• Helps prevent overfilling, leaking, erratic dispenser flow, or poor ice production caused by excessive pressure
• Works with the water inlet system to ensure consistent fill cycles and reliable dispensing
• Compatible with models that use WP74006429 as the factory regulator

• One pressure regulator

• Shut off water supply and unplug the appliance before replacing the regulator
• Inspect fittings and tubing for damage; replace any worn connectors or seals
• Tighten fittings securely and check carefully for leaks after restoring water and power

Color: gray. Measures about 2 inches in diameter.

This surface burner control knob replaces a worn gas knob on your range or cooktop, restoring a solid feel and precise flame adjustment so you can reliably turn burners on, set heat, and shut them off.

• Mounts on the surface burner valve stem to control gas flow and heat level
• Addresses cracked, stripped, or missing knobs
• Helps when a knob spins without engaging the valve or feels loose
• Restores clear, consistent control of burner on/off and flame settings

• Turn all burner controls to Off, unplug or disconnect power, and allow the surface to cool
• Pull the old knob straight off the valve stem; avoid prying with tools that could damage the panel
• Align the new knob with the stem and press straight on until fully seated
• Verify smooth operation through Off, Ignite, and Low-to-High settings

This 6-inch surface coil element restores reliable heat to one burner on your electric range. Replace a burned-out or damaged coil to bring back consistent, even heating for everyday cooking.

• Provides cooking heat for a 6-inch burner position on electric ranges/cooktops
• Helps resolve a burner that won't heat or heats intermittently
• Addresses uneven heating or visible hot spots on the coil
• Replaces elements with visible breaks, blistering, or burned terminals

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• For plug-in coil models: lift the element, pull straight out of the receptacle, and remove from the support/drip pan
• Align the new element's terminals with the receptacle, push firmly until fully seated, and set into the support
• Inspect the receptacle and wiring for heat damage and replace any compromised components before use

This LP orifice kit supplies four factory-style liquid propane burner orifices to convert the cooktop burners for use with LP gas, restoring proper fuel flow for reliable ignition and consistent flames. What it does:

• Replaces LP burner orifices to set correct fuel jet size for propane
• Helps correct weak, uneven, or hard-to-light burner flames after conversion
• Restores consistent burner performance and heat output when properly installed
• Matches OEM fit and flow characteristics for compatible cooktops

• Four (4) LP burner orifices as shown

• Follow the appliance conversion instructions and local codes; conversion often requires replacing orifices and adjusting orificing settings
• Turn off the gas supply and electrical power before starting work
• Use proper tools; do not enlarge or modify orifices

Right rear

Left front

This backsplash restores the rear trim behind a range or cooktop, protecting the wall and covering wiring openings for a clean, factory-look finish. It replaces a damaged, dented, or missing backsplash to improve safety and appearance. What it does:

• Covers the gap between the cooktop and the wall to block spills, splashes, and heat from reaching the wall surface
• Hides wiring and mounting holes for a neat, finished look
• Replaces bent, cracked, or corroded rear trim that can collect grease and grime
• Helps maintain proper clearance and original appearance of the appliance

• One single-piece backsplash

• Basic hardware and mounting locations are OEM-specific; confirm matching fasteners on arrival
• Turn off power to the appliance and move the unit away from the wall before removing or installing the backsplash
• Use care to avoid scratching the finish during installation; two people may be needed for larger ranges
• If mounting holes or brackets are damaged, replace those items before installing this backsplash

Replacement gasket that restores a tight seal to the appliance door and helps prevent water or air leaks. Replaces worn, cracked, or compressed seals so the door closes properly and reduces moisture or heat loss. What it does:

• Seals the door opening to stop leaks of water, steam, or heated air.
• Helps maintain proper temperature and efficiency by preventing air exchange.
• Reduces condensation, odors, and cycling caused by a poor seal.
• Common signs you need this part: visible gaps or damage, leaks around the door, excess moisture, or poor heating/cooling performance.

• Disconnect power and water (if applicable) and allow the appliance to cool before starting.
• Clean and dry the mating surface to ensure a proper fit; remove old adhesive or debris.
• Align the gasket into the door channel or groove and press evenly; avoid stretching the material.
• If the door or mounting hardware is bent or damaged, repair those parts before installing the gasket.

The Grease Filter is an OEM part for Whirlpool downdraft cooktops. It is responsible for removing grease and other cooking residue from the air before it is circulated back into the kitchen.

Causes of a bad grease filter include excessive grease buildup that prevents proper airflow and filtration. Grease filters should be cleaned regularly according to the manufacturer's recommendations.

Symptoms of a grease filter that needs replacement include:

• Reduced or inefficient airflow while in use
• Visible grease buildup or clogging of the filter screens

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This surface igniter is the replacement spark electrode used on gas cooktop burners to create the spark that lights the burner. It restores reliable ignition so burners light when you turn the control knob. What it does:

• Produces the spark that ignites the gas at a surface/burner element
• Replaces a cracked, worn, or non-sparking electrode
• Common fix for burners that click but won't light or that fail to spark
• Works with the existing electrode wiring and mounting location

• Disconnect power to the range and turn off the gas supply before starting
• Handle the ceramic tip gently to avoid chipping; do not touch the tip with bare hands
• Confirm correct orientation and secure mounting; match wiring to original connections

This drip bowl catches and channels excess moisture or drips to help keep the area under the dispenser or ice/water outlet clean and dry. Durable molded plastic resists staining and is shaped for correct fit and drainage. What it does:

• Collects and directs drips from the dispenser or outlet to prevent pooling
• Helps reduce water on the cabinet floor and in the drip tray area
• Restores proper alignment and containment when the original bowl is cracked or warped
• Compatible with units that use an 8" black drip bowl as the dispenser/collector component

• One 8" black drip bowl

• Remove power to the appliance before beginning any service
• Typically snaps or slides into place; check for retaining clips or mounting tabs
• Inspect surrounding seals and gaskets; replace if damaged to prevent leaks

This single electronic control replaces a failed console control to restore user input and cycle selection. It provides the appliance's primary interface for selecting settings and signaling the main control board. What it does

• Receives and processes user inputs to start and control cycles
• Sends commands to heating/motor/timing systems so selected cycles run correctly
• Can correct symptoms like unresponsive buttons, incorrect or no cycle starts, or intermittent control behavior
• Interfaces with the appliance's wire harness and mounting bracket for secure installation

• Disconnect power before removing the old control to avoid shock.
• Handle the control and printed circuit board carefully; avoid static discharge and mechanical stress.
• Removal typically requires control panel or console disassembly and unplugging the wire harness—keep fasteners and connectors organized.

This electronic oven control replaces the console control used to operate a single-convection oven, restoring user inputs and cycle selection so you can reliably set temperature, timers and cooking modes. Ideal when display, touchpad or convection functions fail. What it does:

• Replaces the oven's main user control to allow selection of bake, broil, convection and timed functions
• Restores touchpad/button input and on-screen feedback when controls are unresponsive or blank
• Helps resolve symptoms such as no display, unresponsive buttons, or inability to start bake/convect cycles
• Interfaces with oven components to relay temperature and command signals to the heating system

• One control (single-conv) as shown

• Disconnect power at the circuit breaker before starting any work to avoid shock hazard
• Handle the control assembly carefully; avoid touching circuit board components and use anti-static precautions if available
• Installation typically requires removing the oven console or back access panel and unplugging the old control connector—refer to OEM service instructions