Jenn-Air Cooktop Parts

This clip secures appliance panels or small components to maintain alignment and reduce vibration, restoring the original fit where a worn or broken fastener allows movement or rattling. Simple, direct-fit replacement when the original clip fails. What it does:

• Holds trim, panels, or small components in position to prevent rattling and shifting.
• Replaces broken or missing fasteners that allow loose or misaligned parts.
• Helps keep wiring harnesses or insulation routed and secured in assemblies.
• Small, inexpensive part commonly used wherever a retaining clip is specified.

• Always disconnect power (unplug or shut off circuit) before servicing the appliance.
• Remove panels or trim per the manufacturer service sheet to access the clip; note the clip orientation before removal.
• Use appropriate tools (needle-nose pliers, trim tool) and avoid over-bending the clip or adjacent parts.
• Replace them with the correct OEM-specified clips for reliable fit.

The Gas Range LP Conversion Kit is an OEM part for specific Whirlpool gas ranges. It allows built-in ranges fueled by natural gas to be safely converted for use with liquid propane (LP) fuel. 

Symptoms requiring an LP conversion would include: 

• Inability to ignite or achieve proper combustion using natural gas 
• Unstable burner flame patterns or inconsistent heat output
• Gas leaks or improper connection to an LP fuel supply

Causes for needing an LP conversion kit include choosing to install the range in an area only serviced by LP gas, rather than natural gas. Additional causes could be wear and failure of the original equipment over time.  

This OEM kit is compatible with select Maytag, KitchenAid, Jenn-Air, and Kenmore gas ranges.

This replacement control knob restores a secure grip and accurate selection of settings on your appliance's control shaft. Swap a cracked, stripped, or missing knob to keep everyday operation smooth, precise, and safe.

• Attaches to the control shaft to select temperature, cycle, or burner settings
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps resolve issues like a knob spinning freely, difficulty turning, or inability to choose a setting
• Restores normal feel and alignment when turning the control

• Unplug the appliance and, if applicable, shut off gas before servicing
• Pull the old knob straight off the control shaft; avoid prying on the stem
• Align the new knob with the shaft and press firmly until fully seated
• Test operation to ensure smooth turning and proper engagement

This grate foot cushions and stabilizes a burner grate on your cooktop. Replacing worn or missing feet helps keep the grate level and protects the surface from scratches, rattling, and metal-on-porcelain contact during cooking.

• Provides a protective cushion between the grate and cooktop surface
• Helps keep cookware level by stabilizing the grate
• Reduces noise and vibration during burner operation
• Replace if feet are missing, flattened, cracked, or the grate rocks

• Turn off power/gas and allow the cooktop and grates to cool completely
• Remove the grate; clean the foot recess and any old adhesive or residue
• Press the new foot firmly into place; if your model uses adhesive, apply a manufacturer-approved high-temperature adhesive and allow it to cure as directed
• Reinstall the grate and verify it sits flat and stable before use

This replacement top burner knob restores smooth, reliable control of your cooktop or range surface burner. Use it to turn the burner on/off and adjust heat when the original knob is cracked, stripped, or missing.

• Mounts on the burner valve or switch stem to control flame/heat level
• Replaces knobs that are broken, loose, or no longer engage the stem
• Helps resolve issues like spinning freely, falling off, or hard-to-set heat
• Restores precise burner control and a clean, finished look

• Allow the appliance to cool; disconnect power and shut off gas before servicing
• Pull the old knob straight off the stem; do not pry on the valve stem
• Align the new knob with the stem and press straight on until fully seated
• The knob markings match the correct burner position before use

Color: chrome. Measures about 2 inches in diameter.

Color: Stainless

This ignition switch controls spark to a gas range burner so burners light reliably when a knob is turned. Replaces a worn or failed switch to restore normal ignition and consistent burner operation. What it does:

• Sends the electrical spark signal to the burner igniter when the control knob is turned
• Allows the range to ignite burners; a failed switch can prevent sparks and burner ignition
• Works with the range's safety/ignition system to enable proper start-up sequencing
• Helps eliminate intermittent sparking or no-spark symptoms linked to a faulty switch

• Disconnect power and turn off the gas supply before beginning service
• Basic hand tools required; access may require removing the cooktop or control panel
• Handle electrical connections carefully and restore grounding; follow manufacturer instructions

Replacement grommet that fits under a range grate foot to cushion and stabilize the grate, helping reduce noise and prevent scratching or shifting of the cooktop grate during use. What it does:

• Cushions and secures grate feet to stop rattling and unwanted movement.
• Helps protect the cooktop finish from scratching and wear where the grate contacts the surface.
• Can address noisy, loose, or rocking grates caused by worn or missing grommets.
• Restores proper grate alignment for safer, more stable cooking.

• Ensure the appliance is off and completely cool before starting any service.
• Lift the grate, remove the old grommet, and press the replacement onto the grate foot until fully seated.
• If multiple grommets show wear, replace matching feet for even support.

This small burner gasket seals the cooktop burner to help keep spills and debris out of the burner cavity for more reliable ignition and easier cleaning. It replaces a worn or brittle gasket to restore the burner's fit and seal. What it does:

• Creates a tight seal between the cooktop and the small surface burner to help prevent food, liquid, and debris from entering the burner area
• Helps maintain consistent burner alignment for reliable ignition and even heating
• Reduces the need for frequent deep cleaning by blocking spill penetration
• Commonly replaced when the gasket is cracked, flattened, burned, or missing

• One small burner gasket

• Disconnect power to the appliance before servicing; for gas ranges, turn off the gas supply when applicable
• Remove burner components and replace gasket, ensuring it seats evenly around the burner opening
• Do not force or stretch the gasket; inspect surrounding components for damage and clean surfaces before installing

The Clip is an OEM component specifically designed for Whirlpool free-standing electric ranges, securely fastening rack guides, and wire assemblies. This versatile clip features corrosion-resistant anchors and firm spring coils.

Causes of failure involve metal fatigue weakening the spring over years of expansion and contraction during heating, worn surfaces losing grip, or damaged barbs failing to anchor the racks correctly.

Symptoms of a bad cooking rack clip include:

• Loosened racks skewing pans off-center  
• Detached wires posing burn and electrical hazards
• Rattling components exacerbating noises  
• Difficulty transferring baking sheets without obstruction

Replace yours today with this genuine OEM Whirlpool clip. Compatible with KitchenAid, Maytag, and Jenn-Air appliances as well, its reinforced coils maintain constant tension for organized baking.

This genuine-style replacement power cord restores electrical connection to compatible appliances, letting the unit receive mains power safely. Use it to replace frayed, damaged, or missing cords and stop intermittent or no-power issues. What it does:

• Carries mains power from the wall outlet to the appliance
• Replaces damaged or worn cord that causes intermittent power or no power
• Eliminates exposed wires, melting, or visible cord damage that can be a safety hazard
• Restores secure strain relief and connector fit when original cord is failing

• Disconnect the appliance from power before starting any work
• Follow the appliance service manual for access and wiring; correct terminal connections
• Tighten strain relief and secure wiring to prevent pinching or chafing

This small mounting clip secures small panels and components on compatible Whirlpool appliances, restoring proper fit and preventing parts from coming loose. It's a simple replacement that helps stop rattles and misaligned panels. What it does:

• Secures trim, panels or small components to the appliance frame to maintain proper alignment
• Prevents parts from shifting or vibrating during operation, reducing rattling noises
• Restores fit where a broken or missing clip allowed gaps or loose pieces
• Designed to snap into place for a secure hold without added hardware

• One clip

• Disconnect power to the appliance before attempting any repair
• Remove any trim or panels carefully to access the clip location; note original orientation
• Press or snap the clip into the mounting slot until it seats; some locations may require a flat tool or light force
• Replace or repair the adjacent parts for a secure fit

This switch seal is a small rubber gasket that protects a control or door switch from moisture and debris, helping maintain reliable operation and prevent damage to the switch assembly. What it does:

• Creates a moisture- and dust-resistant barrier around a switch to reduce shorting and corrosion
• Helps keep switches operating smoothly by blocking contaminants that cause sticking or intermittent contacts
• Supports safe electrical performance by keeping water away from switch terminals and housings
• Common symptom linkage: switch malfunction, intermittent control, or moisture-related failures near switch area

• Disconnect power to the appliance before inspecting or replacing the seal
• Remove surrounding trim or components carefully to avoid damaging the switch or housing
• Confirm correct orientation and full seating of the seal during reassembly for an effective barrier
• If the switch shows damage or corrosion, replace the switch assembly as well

This is a replacement control knob that restores a worn or broken selector on a household range or cooktop. It provides a secure grip for turning controls so settings stay accurate and easy to change. What it does

• Replaces a stripped, cracked or missing control knob so you can select temperature or function again
• Restores tactile grip and clear position alignment for reliable control
• Stops slipping or wobbling that can prevent accurate adjustments
• Simple push-on design aligns to the control shaft for consistent operation

• Disconnect power to the appliance before servicing controls to avoid injury
• Most installations are push-on: pull the old knob straight off and push the new knob fully onto the splined shaft
• If the knob is tight, use a steady pull or a knob-puller tool to avoid damage
• Align pointer/indicator to the control scale before using