Jenn-Air Cooktop Parts

Color: Black

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

This surface heating element replaces a damaged or nonworking stovetop burner to restore even heat for cooking. It fits most compatible electric ranges and gives you a direct replacement for a faulty top burner element. What it does

• Provides the heating element that transfers heat to cookware on the cooktop
• Restores proper burner heat when an element no longer warms or cycles correctly
• Helps eliminate uneven cooking or intermittent on/off heating from a failed element
• Works as a direct replacement for the corresponding top/burner element on compatible ranges

• Disconnect power to the range before removing or installing the element to avoid electrical shock
• Pull the element straight out of the terminal block; avoid bending terminals or damaging the receptacle
• Inspect the burner receptacle for damage and replace if corroded or loose
• After installation, test the element on low and high settings and watch for proper operation

This surface igniter is the replacement spark electrode used on gas cooktop burners to create the spark that lights the burner. It restores reliable ignition so burners light when you turn the control knob. What it does:

• Produces the spark that ignites the gas at a surface/burner element
• Replaces a cracked, worn, or non-sparking electrode
• Common fix for burners that click but won't light or that fail to spark
• Works with the existing electrode wiring and mounting location

• Disconnect power to the range and turn off the gas supply before starting
• Handle the ceramic tip gently to avoid chipping; do not touch the tip with bare hands
• Confirm correct orientation and secure mounting; match wiring to original connections

Replacement infinite-switch control knob that restores reliable heat selection on electric cooktops and ranges. Push-on design lets you set burner heat levels precisely and replaces cracked, faded, or missing knobs. What it does:

• Turns the infinite switch to select burner heat level and set cooking temperatures.
• Restores a secure grip and tactile detents when the original knob is cracked, worn, or missing.
• Helps when a knob spins, slips, or won't stay set on a chosen heat setting.
• Works with push-on style infinite switch shafts commonly used on electric ranges and cooktops.

• Always disconnect power to the appliance before servicing to avoid shock or injury.
• Typically installs by pulling the old knob straight off the control shaft and pushing the new knob onto the shaft until seated.
• Inspect the switch shaft for wear or damage; a stripped shaft may require replacing the infinite switch rather than the knob.
• If the knob is tight to remove, use a firm, even pull or a suitable knob-puller tool; avoid excessive prying that could damage the control panel.

Color: White

This white valve knob replaces a worn, cracked or missing control knob so you can safely and easily adjust burner or oven settings. It restores a secure grip and precise control for temperature or flame adjustments. What it does:

• Replaces a damaged or stripped control knob used to turn gas or electric valve controls
• Provides a positive grip so settings can be changed smoothly and accurately
• Helps stop slipping or spinning that prevents proper temperature or flame adjustment
• Matches original fit to engage the control shaft properly when installed

• Turn off power and gas supply before removing the old knob
• Pull off the old knob straight from the control shaft; align splines and push new knob fully onto the shaft
• Do not force or hammer the knob; ensure it seats squarely to avoid damage
• Test control operation after installation and restore power/gas only when connection is secure

Color: black. Measures about 2 inches in diameter, by 2 inches deep.

This burner switch controls the power and heat settings for a surface cooking element, restoring reliable on/off operation, accurate temperature selection, and consistent element cycling on compatible electric ranges. What it does

• Regulates electrical power to a surface burner so the element heats to selected settings and cycles to maintain temperature.
• Replaces a worn or failed switch that causes a burner to not heat, not respond to knob changes, or only work on certain settings.
• Stops intermittent operation or arcing at the switch caused by worn contacts.
• Helps resolve a burner that stays on or will not turn on when the switch is faulty.

• Always disconnect power at the breaker before starting any repair to avoid shock.
• Photograph and/or label wires before removal so you can reconnect terminals correctly.
• Handle terminals gently and ensure secure, tight connections; replace any damaged wiring or connectors.
• Test the range on all heat settings after installation; if you see arcing, burning smell, or continued malfunction, cut power.

For switch mounting nut, order part# WP422617.

A hi-limit safety switch that stops heating when temperatures get too high, protecting the appliance from overheating and helping prevent damage. Designed to replace a failed thermal cutoff to restore safe temperature control. What it does:

• Opens the heating circuit when internal temperature exceeds the safe limit to prevent overheating
• Commonly replaces a failed or intermittently opening thermal limit control
• Helps stop burners or heating elements from running unchecked when a thermostat fails
• Addresses symptoms like no heat, intermittent heating, or safety trip shutdowns

• Disconnect power before accessing heating components and wiring
• Verify the part matches the appliance diagram and wiring orientation before installation
• If corrosion or other damage is present on connectors or terminals, replace or repair per OEM guidance

A replacement burner knob for electric ranges that restores reliable control of a surface element. Simple, direct fit for the matching original control shaft and restores user control of heat settings. What it does

• Replaces a worn, melted, cracked, or missing burner control knob to allow safe adjustment of the surface element.
• Engages the stove/range control shaft so settings click and hold as intended.
• Helps prevent slipping or inaccurate temperature selection caused by a damaged knob.
• Matches the original shape and fit for intuitive operation.

• One replacement burner knob (single).

• Install is typically plug-and-play: pull off the old knob and push the new knob onto the control shaft; no tools usually required.
• Disconnect power to the appliance before working near controls if removing any control panel components.
• If the knob does not seat properly, stop and verify shaft style to avoid damage.

Made for use on an range, this part is a cooktop. It is manufactured out of a high-quality black glass material. The purpose of this component is to provide a stable surface to cook on. It also houses the cooking burners.The cooktop will need to be replaced if it is cracked or broken in any way. It can become cracked if something heavy comes into forceful impact with it. Sometimes, if food is burned badly on the surface, the cooktop will need to be replaced for cosmetic purposes or for operational issues. Make sure to unplug the refrigerator from the electrical outlet before trying to replace this part. Allow the unit ample time to cool down before starting this process.This component is sold individually and is sourced directly from the manufacturer. This specific cooktop is compatible with ranges that are manufactured by the Whirlpool and Jenn-Air brands.

Seal tape restores a tight seal around appliance doors and panels to help prevent air or moisture leaks and improve temperature stability. Use it to replace worn or missing sealing strips that allow drafts, frost, or heat loss. What it does

• Creates a flexible barrier to close small gaps and reduce airflow or moisture migration at door and panel seams.
• Helps maintain correct internal temperatures and can reduce frost buildup or inefficient cooling/heating.
• Replace when tape is cracked, compressed, detached, or visibly deteriorated.
• Commonly used where a thin, form-fitting sealing strip is needed on appliance doors and access panels.

• One seal tape.

• Clean and dry the mating surface before installing for best adhesion; remove old residue.
• Cut to fit and press firmly along the length to seat the tape; trim excess as needed.
• Disconnect power (unplug or switch off breaker) before starting.

This blower motor moves air through the dryer to help vent heat and moisture so clothes dry efficiently. Replaces a worn or failed blower motor to restore proper airflow and drying performance. What it does:

• Spins the blower wheel to force air through the drum and exhaust vent
• Restores normal airflow when the dryer has little or no air movement
• Helps stop rattling, squealing, or grinding noises caused by a failing motor
• Helps reduce long dry times and overheating caused by restricted or weak airflow

• One blower motor

• Disconnect power to the appliance before starting any repairs
• Installation typically requires removing the dryer front or rear panel and accessing the blower housing
• Inspect the blower wheel and housing for lint or damage while replacing the motor

This control panel assembly provides the front-facing electronic interface and buttons that let you select cycles, options, and start or stop the appliance. It restores responsive controls and readable push-button or touch operation. What it does:

• Houses the appliance's main user controls and display so you can select cycles and settings
• Sends user commands to the main control board for operation
• Replaces worn, cracked, or non-responsive buttons or a faded display
• Helps resolve issues where buttons don't register or the panel shows no response

• One control panel assembly as shown

• Disconnect power before attempting service to avoid electrical shock
• Replacement generally requires removing the front console or trim; keep screws and connectors organized
• Handle the panel carefully to avoid damaging the display and ribbon/connectors