Jenn-Air Range / Cooktop / Oven Parts

Color: metallic. Measures about 11 inches wide by 2-1/2 inches high.

This replacement roller fits the front or rear position of a slide mechanism, restoring smooth, even movement and reducing noise when a wheel is worn or broken. It helps racks or drawers glide properly and stay aligned. What it does:

• Provides low-friction rolling support for the slide track
• Helps slide-out assemblies move freely without binding or scraping
• Worn or damaged rollers can cause sticking, squeaking, or uneven travel
• Restores proper alignment and smooth operation when replaced

• 1 roller assembly

• Disconnect power and allow the appliance to cool before servicing
• Remove the slide-out assembly; note roller orientation and hardware
• Transfer/reuse existing screws, clips, or retainers as required
• Do not lubricate unless the manufacturer specifies a lubricant

Restore a tight, heat-holding seal around your oven door. This replacement door gasket helps keep heat and moisture inside the oven for more consistent temperatures and reliable cooking performance. What it does

• Seals the gap between the oven door and front frame to contain heat and vapor
• Helps the oven reach and maintain set temperatures for even baking and roasting
• Reduces heat escape that can cause longer preheat times or temperature swings
• Replaces seals that are torn, frayed, flattened, or leaking heat around the door

• 1 oven door gasket

• Disconnect power and allow the oven to cool completely before servicing
• Open the door and remove the old gasket by releasing its retaining clips; note orientation
• Start at the top center and press the new gasket into place evenly—do not stretch it
• Close the door and check for a uniform seal all around; readjust as needed

This control panel assembly is the front console that houses the oven/range user interface and display, restoring visible controls and user input so you can select cycles, set temperatures, and monitor settings. What it does

• Contains the control interface (buttons/touchpad and display) used to select functions, temperatures and timers.
• Re-establishes visible feedback and input when buttons are unresponsive or the display is blank or flickering.
• Helps restore control of oven/range functions when the console is cracked, damaged, or failing.
• Works as the direct replacement for the damaged or nonworking control console to return normal user operation.

• Disconnect power at the breaker or unplug the appliance before starting—electrical shock hazard.
• Handle the display and trim carefully to avoid damage; some wiring harnesses or connectors must be disconnected and reattached.
• Keep track of screws and retainers; a basic screwdriver set is usually required.

This valve knob replaces a worn or broken control on a gas range or cooktop. It attaches to the burner valve shaft so you can turn the burner on/off and adjust the flame with smooth, reliable control.

• Couples to the surface burner valve shaft to select Off/High/Low and regulate flame
• Restores control when the original knob is cracked, stripped, loose, or missing
• Provides a secure grip and proper alignment with panel markings for accurate settings

• Turn all controls to Off and let the surface cool before starting; disconnect power if working near igniters
• Pull the old knob straight off the valve shaft—do not pry sideways
• Align the flat/D-shaped opening with the shaft and press straight on until fully seated; verify the Off position aligns with the panel
• If the knob does not seat easily, stop and recheck the part number and shaft style

Color: Black

Right front

This electronic control board is the appliance's main control module that processes user inputs and manages cycle operations so the unit responds correctly. Replace a failed board to restore normal control and display functions. What it does:

• Receives signals from the user interface and controls timers, relays, and system sequencing
• Powers and coordinates heating/motor/cycle commands as directed by selected settings
• Common symptoms: blank or erratic display, unresponsive touchpad/buttons, cycles won't start, or intermittent operation
• Works as the central logic board; does not include user interface or touchpad

• Disconnect power before service to avoid shock or damage
• Handle the board by its edges and avoid static discharge; ground yourself before touching electronics
• Verify all wire harness connectors are fully seated and mounting hardware is secure after installation

The Burner Grate is an OEM part for Whirlpool ranges. It sits above the burner elements underneath the cooktop surface, allowing heat to radiate up through the grates to cookware. The burner grate disperses heat evenly while remaining cool to the touch when not in use.  

Symptoms of a bad burner grate can include:

• Warping or sagging from long term heat exposure
• Discoloration or material deterioration over time
• Loose or uneven fit that allows spillage between burner holes

Causes of failure may be natural wear and tear from extended cooking use, damage from improper cleaning procedures, or malformations due to use of oversized cookware.

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

A replacement oven door seal that restores a tight gasket between the oven and door. It helps prevent heat loss, reduce uneven cooking and keep the exterior cooler for safer, more consistent results. What it does:

• Creates an airtight seal between the oven cavity and door to reduce heat escape.
• Helps maintain stable cooking temperatures to minimize hot spots and uneven baking.
• Stops smoke or fumes from leaking around the door during use.
• Visible signs of failure include tears, compressed or brittle material, and gaps along the door edge.

• Disconnect power (or gas supply) and allow the oven to fully cool before starting work.
• Handle the gasket gently to avoid tearing; align and seat it into the door channel per the OEM pattern.
• Some models require removing the oven door or retaining clips — keep and reuse any factory fasteners when possible.
• Refer to the appliance's OEM service instructions for model-specific removal and reinstallation guidance.

This spark ignitor ground assembly creates the spark and grounded path needed to light a gas burner. Replacing a worn electrode restores consistent ignition and helps reduce continuous clicking or burners that fail to ignite.

• Generates a high-voltage spark at the electrode tip to ignite the gas at the burner
• Integral ground bracket completes the circuit and sets the proper spark gap near the flame source
• Common symptoms: no spark at one position, intermittent ignition, continuous clicking, or cracked/corroded electrode or ground
• Intended for a single burner location; match mounting style and connector to your original

• Disconnect power and shut off gas; allow the appliance to cool before servicing
• Note the original electrode position and wire routing; remove the old assembly
• Install the new assembly with clean, tight metal-to-metal ground contact and correct gap to the burner per service instructions
• Reconnect the lead and test for a strong, consistent spark before reassembly

This leveling leg screw threads into the appliance base to raise or lower the chassis, helping you stabilize the unit on uneven floors. Replace a missing, bent, or stripped screw to restore solid, level footing.

• Provides fine height adjustment when paired with the leveling leg/bracket
• Helps eliminate rocking, rattling, or vibration caused by an unlevel appliance
• Restores adjustability when original screw is stripped, bent, or missing
• Helps maintain proper alignment with cabinets/countertops by keeping the unit level

• Disconnect power; for gas units, shut off the gas supply before beginning
• Pull the appliance forward and carefully lift or tip to access the leveling hardware—use a helper to prevent tipping
• Remove the old screw; start the new screw by hand to avoid cross-threading, then adjust height with a wrench until level
• Verify all corners contact the floor and recheck level after repositioning the appliance

This upper oven broil element delivers direct, intense heat for broiling and top-browning. Replace a failed element to restore fast, even broiling performance and consistent top heat in your electric range or wall oven.

• Provides high radiant heat from the top of the oven during Broil for searing and browning
• May cycle on for top-browning during Bake (on some models)
• Typical failure symptoms: no broil heat or slow, uneven top browning
• Replace if the element is cracked, blistered, pitted, or sparks/arcs when energized

• Unplug the appliance or switch off power at the breaker before servicing
• Remove oven racks; unfasten the element's mounting screws/clips and gently pull the element forward
• Transfer wires one at a time and support them so they don't slip back through the oven liner
• Avoid bending the new element; secure brackets/screws, restore power, and test broil

This igniter switch assembly replaces a worn or failed switch that controls ignition to a gas burner or oven igniter, restoring reliable spark/ignition and consistent burner operation. What it does

• Acts as the electrical switch that signals the igniter or spark module to light a burner or oven
• Helps resolve intermittent or no-spark ignition symptoms and burners that fail to light
• Restores proper on/off switching for the ignition circuit when the original switch is damaged or worn
• Works as the direct replacement switch component in the ignition system

• One igniter switch assembly

• Disconnect power and shut off gas supply before starting any repair
• Use basic hand tools; handle wiring connectors carefully to avoid damage
• Verify part compatibility with your model before installation

This replacement microwave door restores a secure seal and a clear view into the cavity. Replace a cracked, bent, or misaligned door to help the interlocks engage properly so the oven can start and operate safely.

• Provides the door assembly used to open/close the microwave, with viewing window and latch hooks that actuate the door switches
• Seals the cavity perimeter via the choke to help contain microwave energy when latched
• Common symptoms include: door won't close or latch, oven won't start or shows a door-ajar error, or visible damage to the door frame or glass
• Helps resolve issues caused by a warped/bent door, broken trim, or loosened components

• Disconnect power before servicing; do not remove the microwave's outer cabinet
• Support the door, lift it off the hinges, and protect hinge springs and latch areas from damage
• Transfer any model-specific trim or hardware from the original door if required
• Align hinges and latch hooks; verify the door closes flush and latches securely.

This surface heating element restores reliable heat to an electric cooktop burner so pots and pans warm evenly and predictably. Replace a failed element to bring consistent performance back to your range or smooth-top cooktop.

• Supplies heat to a single cooking zone on an electric range or glass-top cooktop
• Replaces an element that is open, shorted, or intermittently heating
• Common symptoms: burner won't heat, heats unevenly, or only part of the zone glows
• Helpful when there is visible damage or hot spots on the element

• Disconnect power at the breaker; allow the cooktop to cool completely
• Access the element by lifting/removing the cooktop or from below
• Move wires one at a time to matching terminals; reuse any mounting clips/brackets as required
• Support the glass top during service and avoid stressing or scratching the surface