Jenn-Air Refrigerator Parts

This temperature control assembly monitors and helps regulate appliance temperature so the unit maintains expected cooking/cooling performance and resolves temperature-related operation issues. It replaces a failed control to restore consistent temperature response. What it does:

• Senses and controls internal temperature to help maintain set points
• Can correct symptoms such as incorrect temperature, extended heat/cool cycles, or inconsistent performance
• Interfaces with the appliance control system to activate heating/cooling components as designed
• Mounts in the control area and connects to existing wiring harnesses for direct replacement

• Disconnect power to the appliance before starting any service
• Access may require removing the console or rear access panel; follow the service manual for your model
• Handle the control assembly and connectors carefully to avoid damage; match wire locations during reassembly

Made by Whirlpool. This kit includes 15 feet of copper tubing, saddle valve, teflon tape, and tubing connector. Use this kit to connect your refrigerator ice maker to water supply (usually your water shut off valve under the kitchen sink).

This is a refrigerator drip pan kit. It is located on the bottom of the appliance and is used to help catch condensation from the appliance. Any moisture that is made while the refrigerator goes through its operation cycles will collect in the pan to prevent a mess. If the drip pan has been damaged, the most common symptom is water dripping on the floor. Checking for a clog should be done. If the actual part is damaged, it will need to be replaced.Before replacing the drip pan kit, unplug the power cord on the appliance and pull the refrigerator from the wall. Use a nut driver to release the water inlet line coupler before taking off the access panel. Reach in and bend the pan retaining tab, open the doors of the appliance, and take off the water filter cover. Remove the toe plate to access and replace the drip pan.This is a genuine OEM drip pan kit that can be used as a replacement for Dacor, Jenn Air, Hardwick, and Maytag refrigerators. It is sold as an individual component and is provided directly from the manufacturer.

This replacement blade is the rotating element used within the appliance assembly to deliver the intended action. Installing a new blade restores smooth, efficient operation when the original is cracked, bent, worn, or missing.

• Provides the mechanical action required by the assembly (rotation/agitation)
• Helps maintain consistent performance and smooth operation
• Common failure signs: rattling or scraping noises, vibration/wobble
• Other symptoms: reduced performance in that section of the appliance, visible chips, cracks, or deformation

• Disconnect power before servicing; turn off water supply if applicable
• Wear cut-resistant gloves; edges may be sharp
• Note the original blade's orientation and spacing before removal; install the new blade the same way
• Hand-rotate after installation to ensure free movement and clearance before restoring power

The Hinge Bushing is an OEM component specifically designed for Whirlpool refrigerator doors. It is a circular bearing and support component that promotes smooth door swinging. The bushing fits within hinges to reduce friction and prevent premature wear.  

Causes of compromised hinge bushings can be years of door opening compressing the bushing material. Exposure to moisture also contributes to cracked, pitted or damaged bushings failing to guide doors effortlessly.

Symptoms of failing hinge bushings include:

• Stiff or resistant door movement requiring extra effort  
• Noisy hinges or grinding sounds due to metal-on-metal contact
• Misaligned or sagging doors unable to fully latch or seal
• Premature wear of connecting hinge parts forcing early replacement

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

A direct-replacement temperature control that restores user control over oven/refrigerator temperature settings for reliable cooking and storage. Replaces a worn or failed control to help stabilize temperature cycles and improve performance. What it does:

• Regulates appliance temperature by opening and closing the control circuit as needed
• Helps correct symptoms like inconsistent temperatures, unit running too long, or failure to reach set temperature
• Works as the control interface between user settings and the heating/cooling system
• Designed to match OEM function and mounting for straightforward replacement

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Use basic hand tools; mounting screws and wiring retainers are typically reused unless new hardware is supplied
• Note wiring locations and take a photo before disconnecting connectors to ensure correct reassembly

This refrigerator air damper control is the motorized assembly that regulates how much cold freezer air enters the fresh food section, helping maintain even, accurate temperatures and consistent airflow across shelves.

• Meters airflow from the freezer to the refrigerator via a motor-driven damper door
• Helps the control system reach and maintain target temperatures
• Failure symptoms include: refrigerator too warm, items freezing near the vent, weak or no airflow from the diffuser, or repetitive clicking/ratcheting noises from the damper area
• A stuck-open or stuck-closed damper can cause temperature swings or ice buildup around the vent

• Disconnect power to the refrigerator before servicing
• Access the damper from inside the fresh food compartment; remove shelves and the cover/console as needed
• Unplug the wire harness and remove mounting screws; transfer any foam seals or ducts from the original to the new assembly if required
• Reassemble, restore power, and allow up to 24 hours for temperatures to stabilize

This replacement lid fits the refrigerator utility/bin drawer and restores a secure cover to keep stored items contained and organized. It replaces cracked, broken or warped lids so the bin functions as intended. What it does:

• Covers and protects items stored in the utility/bin drawer
• Replaces lids that are cracked, chipped or no longer latch properly
• Helps prevent items from shifting or falling into other compartments
• Restores a proper seal and alignment of the utility/bin cover

• Unplug or disconnect power to the appliance before servicing for safety
• Remove the bin/drawer per the manufacturer instructions to access the lid
• Align hinge tabs or mounting points and snap or fasten the lid into place
• Handle carefully; plastic edges or mounting points can be fragile during installation

This spacer maintains the correct distance between mating components in your appliance's assembly so parts align and operate smoothly. Replacing a worn or missing spacer can correct looseness, rubbing, or vibration-related noise.

• Holds a precise gap between parts for proper alignment and motion
• Prevents metal-to-metal contact and premature wear
• Helps reduce vibration, rattling, and scraping noises
• Common signs include misalignment, unusual gaps, looseness, or rubbing in the related assembly

• Disconnect power (and shut off gas/water, if applicable) before servicing
• Refer to your model's diagram to locate the spacer's exact location and orientation
• Inspect related fasteners and bushings; replace if worn
• Do not overtighten hardware to avoid deforming the spacer

This replacement bracket provides a secure mounting point for a designated component in your appliance. It keeps parts properly supported and aligned, helping the unit operate smoothly without vibration or shifting.

• Supports and anchors a specific part or assembly in the correct position
• Helps prevent vibration, rattling, and premature wear from movement
• Maintains alignment for consistent, reliable operation
• Replace if bent, cracked, or missing; symptoms can include loose components or unusual noise

• Disconnect power; shut off water or gas supply if applicable
• Access the bracket location per your model's service information and note the original orientation
• Transfer any screws, clips, or grommets from the old bracket to the new one
• Tighten fasteners evenly and verify alignment before restoring power

This control lever secures a refrigerator door shelf bin to the door frame so bins stay seated and stable during normal use. Replacing a broken or worn lever restores proper bin retention and reduces rattling or unexpected bin release. What it does

• Holds the door shelf/bin in place so it doesn't fall out when opening or closing the door
• Aligns and retains the bin on the door track for secure storage
• Stops bin-related rattles and noisy door operation caused by a loose or cracked lever
• Common symptom: bin falls out, won't stay seated, or rattles in the door

• One door bin control lever

• Remove food and take the door bin off the door before replacing the lever
• Inspect the bin and mounting area for damage; clean mounting surfaces if needed
• Lever typically snaps into the door mounting point; align and press until it clicks
• Disconnecting power is not required for most door-bin repairs, but follow all safety precautions and your model's service instructions

Door shelf bin control lever that secures and releases the refrigerator door shelf bin so stored items stay in place; replaces a broken or worn lever to restore proper bin latching and alignment. What it does:

• Locks the door shelf bin into the door track so the bin stays seated during normal use.
• Allows controlled removal and reinstallation of the door bin when lifted or tilted.
• Common replacement when the bin won't latch, slides out, or the lever is cracked or damaged.
• Matches OEM fit to restore original bin operation and alignment.

• Remove all items from the door bin before servicing; set the bin on a soft surface to avoid damage.
• Inspect bin track and mounting points for damage before installing the new lever.
• Most installations require only basic hand tools and snapping the lever into the existing mounting point.
• Always unplug the refrigerator or disconnect power when working near electrical components or lights.

This defrost thermostat senses evaporator temperature to control the defrost heater. Replacing a failed thermostat restores proper defrosting, prevents overheating during the defrost cycle, and helps maintain stable cooling performance.

• Monitors evaporator coil temperature and closes to power the defrost heater during defrost
• Opens the heater circuit as the coil warms to terminate defrost and prevent overheating
• Helps clear frost from the evaporator so air can circulate between freezer and refrigerator
• Failure may present as heavy frost/ice buildup, reduced cooling in the fresh food section, the evaporator fan hitting ice, or a defrost cycle that fails to start

• Disconnect power before servicing; defrost heavy ice as needed for access
• Located on/near the evaporator coil behind the freezer's rear panel, typically clipped to tubing
• Match original clip orientation and wire routing; ensure firm thermal contact with the coil/tube
• After installation, confirm operation with a continuity check at freezer temperature or run a manual defrost test per the service manual

This temperature control thermostat regulates the refrigerator compartment temperature by cycling the cooling system on and off. Replacing a faulty control restores consistent cooling and normal on/off operation so food stays at the right temperature.

• Senses compartment temperature and opens/closes electrical contacts to start or stop cooling
• Useful when the fridge is too warm or too cold despite adjustments
• Common symptoms: runs constantly or won't run, temperatures don't respond to the dial, no click or change when turning the control
• Also called a "cold control"; restores functional temperature adjustment

• Disconnect power before servicing
• Note wire locations and transfer them to the new control
• Carefully route the sensing capillary in the original path; avoid kinking or sharp bends
• Set to a mid-range setting and allow up to 24 hours for temperatures to stabilize

This heater and thermostat assembly replaces the dryer's heating module to restore normal drying performance by regulating and producing heat. It's a direct-fit assembly designed to simplify replacement and reduce diagnosis time. What it does:

• Provides the dryer's primary heating element and temperature control components.
• Regulates operating temperature via built-in thermostats/thermal cutouts.
• Stops heating when a thermostat or thermal cutoff opens, which can cause no-heat or under-heating symptoms.
• Helps address common symptoms like no heat, long dry times, or intermittent heating when diagnosed to this assembly.

• Disconnect power to the appliance before starting service to avoid shock or injury.
• Carefully discharge any residual heat and avoid contact with sharp sheet metal and the heating element.
• Inspect and replace any blown thermal fuses or damaged wiring.
• Follow model-specific instructions and torque/electrical guidelines from the OEM during installation.