Jenn-Air Wall Oven Parts

Includes the touchpad membrane switch.

This oven door inner glass is the interior glass pane within the door assembly. Replace a cracked, shattered, or missing pane to restore a safe seal, a clear viewing window, and consistent heat retention.

• Forms the inner pane of the oven door window to help seal the cavity
• Helps insulate heat so the oven can reach and maintain set temperature
• Provides visibility to monitor cooking without opening the door
• Typical failure signs: cracked or shattered glass, or a missing/damaged pane

• Disconnect power (and shut off gas, if applicable) before servicing
• Remove and disassemble the door to access the glass; note screw locations and pane order
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Reassemble without over-tightening fasteners; verify the door closes and seals evenly

Replacement water filter cartridge for compatible refrigerators. Helps restore clean-tasting water and clearer ice by reducing common taste, odor, and sediment issues. Easy-to-replace cartridge keeps your dispenser and ice maker working properly. What it does:

• Filters common taste, odor and sediment issues that cause off-tasting water or cloudy ice
• Helps prevent particulate build-up that can reduce dispenser and ice-maker performance
• Improves overall water clarity and mouthfeel for drinking and ice
• Common symptoms this part addresses: bad taste or odor, cloudy ice, or reduced water flow from the dispenser

• Replace per the refrigerator manufacturer's instructions; ensure the cartridge fully seats and seals
• After installation, run the water dispenser until flow is clear to flush air and any loose carbon fines
• Dispose of the old cartridge according to local regulations

This factory window pack assembly creates the sealed, insulated glass window in your oven door. It restores a clear view into the cavity and helps the appliance hold temperature when the original window is broken, cloudy, or damaged.

• Forms the sealed, multi-pane window within the oven door
• Helps contain heat and maintain consistent baking temperatures
• Restores visibility into the oven cavity
• Common symptoms: cracked/shattered glass, fogging or streaks between panes, rattling glass, heat escaping near the window area

• Disconnect power and allow the oven to cool completely before servicing
• Wear cut-resistant gloves and eye protection; handle glass vertically and support the edges
• Door removal and partial disassembly are typically required; keep screws and trim organized
• Transfer any reusable brackets/insulation per your model's service information

This burner cap covers the auxiliary (small) gas burner on your cooktop or range. It shapes the flame for even heating and protects the burner head—helping restore reliable ignition and a clean, finished look.

• Sits on the auxiliary burner head to shape and contain the flame
• Promotes even heating and dependable ignition when properly centered
• Shields the burner head from spills and debris
• Replace if the original cap is missing, warped, chipped, or discolored
• Typical symptoms: uneven or yellow flame, delayed ignition or continuous clicking without lighting, weak heat on that burner

• Shut off gas and power; allow the surface to cool before servicing
• Lift off the old cap, clean the burner head, and place the new cap over the auxiliary burner
• Align any locating features so the cap sits flat and centered; misalignment can prevent ignition or cause a yellow flame

The Control Panel is an OEM part for Whirlpool ranges. It facilitates precise input and display of cooking functions.

Causes of replacement include failure of embedded circuits or damage allowing moisture penetration through the membrane surface over time. Physical impacts can distort switch responsiveness.

Symptoms of issues involve:

• Ghosting or pixelation impairing display readability
• Refusal of elements to toggle through temperature settings
• Unresponsive selection buttons due to circuit interruptions
• Inaccurate temperature calibration requiring technician attention

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Black. Kit of 4

This control panel assembly provides the front-facing electronic interface and buttons that let you select cycles, options, and start or stop the appliance. It restores responsive controls and readable push-button or touch operation. What it does:

• Houses the appliance's main user controls and display so you can select cycles and settings
• Sends user commands to the main control board for operation
• Replaces worn, cracked, or non-responsive buttons or a faded display
• Helps resolve issues where buttons don't register or the panel shows no response

• One control panel assembly as shown

• Disconnect power before attempting service to avoid electrical shock
• Replacement generally requires removing the front console or trim; keep screws and connectors organized
• Handle the panel carefully to avoid damaging the display and ribbon/connectors

This electronic control board regulates the appliance's console functions so cycles, settings and displays operate correctly. Replaces a faulty console module to restore responsive controls and normal cycle selection. What it does:

• Manages user inputs, cycle selection and timing signals for the appliance
• Controls display indicators, LEDs and electronic user-interface feedback
• Communicates with other modules to start/stop cycles and control features
• A failed board can cause unresponsive buttons, incorrect displays, or cycles that won't start

• Disconnect power to the appliance before starting any repair to avoid shock
• Handle the board by its edges and avoid static discharge; use an anti-static wrist strap if available
• Verify the part number and appliance model match before installation

This small pan seal replaces a worn or damaged sump/pan gasket to help stop leaks and keep water inside the appliance's drain area. It restores a proper seal so the appliance can drain without pooling or seepage. What it does:

• Seals the small pan/sump area to prevent water from leaking onto the floor
• Helps maintain proper drainage and reduces pooling under the appliance
• Restores a tight gasket where cracks, compressions, or wear allow seepage
• Commonly used when you see water under the unit, drips after cycles, or visible gasket damage

• Disconnect power and water supply before servicing the appliance
• Remove access panels and clean the mating surfaces before installing the new seal
• Press the seal into place evenly; ensure it sits flush in the pan/sump channel
• Inspect surrounding parts for damage and replace any brittle or warped components

This inner oven door glass replaces a cracked or cloudy panel to restore a clear view into the oven and help maintain proper door sealing. Fits models that use the WP7902P444-60 / 208970 assembly. What it does:

• Replaces damaged, cracked, or fogged inner oven door glass to improve visibility and appearance.
• Helps maintain the oven door's barrier between the cooking cavity and room air.
• Can reduce heat loss from a compromised door glass when properly installed.
• Safe, durable glass designed for oven-door use per OEM specification.

• One inner oven door glass panel

• Disconnect power to the appliance before starting any repair.
• Remove the oven door per the manufacturer's instructions to access the inner glass; follow OEM guidance for disassembly/reassembly.
• Handle glass with care and wear cut-resistant gloves and eye protection.
• If screws, clips or gaskets appear damaged during disassembly, replace them with matching OEM parts.

This high-limit thermostat (hi-limit switch) is a temperature safety device that stops the heating circuit if the appliance overheats, helping protect the unit and restore proper heat control when replaced. What it does:

• Opens the heating circuit if internal temperature exceeds safe limits to prevent overheating.
• Controls whether the heater/element receives power based on temperature.
• When faulty, common symptoms include no heat or intermittent heating and repeated thermal cutouts.
• Can be tested for continuity to confirm electrical function.

• One high-limit thermostat (hi-limit switch).

• Disconnect power before inspecting or replacing; risk of shock or injury if energized.
• Note and label wire locations or take a photo before removal for correct reassembly.
• Verify part compatibility with your model before installing; confirm continuity after installation.

This timer knob replaces a worn or broken range timer control knob, restoring a positive grip and reliable dial operation so you can set cooking times accurately. Easy-restore part for common knob damage or wear. What it does:

• Provides a replacement control surface for the oven/range timer so the dial turns smoothly
• Re-establishes a secure connection between the user and the timer shaft for accurate time setting
• Commonly used when the knob is cracked, stripped, loose, or will not engage the timer shaft
• Helps eliminate slipping or intermittent timer operation caused by a damaged knob

• Unplug or disconnect power to the appliance before replacing the knob
• Pull the old knob straight off the timer shaft; align and press the new knob firmly onto the splined shaft
• Do not force the knob at an angle; if it does not seat easily, inspect the shaft for debris or damage
• The timer control assembly may also need replacement

This control knob replaces a worn or missing dial so you can reliably select settings on your appliance. Restore smooth, positive control and a like-new look when an old knob cracks, strips, wobbles, or falls off.

• Attaches to the control shaft so you can choose functions, temperatures, or speeds
• Provides a secure grip for accurate adjustments
• Typical symptoms include a cracked or missing knob, loose or wobbly feel, spinning without engaging, or difficulty turning to Off
• Direct replacement designed to fit the original control stem on compatible models

• Turn the appliance off and allow any hot surfaces to cool
• Pull the old knob straight off the control shaft; avoid prying against the console
• Align the new knob with the shaft and press straight on until fully seated
• Test operation to ensure the pointer aligns with Off and the control engages properly

A replacement oven rack that restores stable support for cookware and baking pans, helping maintain even cooking and safe handling. Designed to fit the original rack slots for reliable, everyday oven use. What it does

• Provides a stable shelf for cookware, bakeware and roasting pans.
• Replaces bent, rusted or damaged racks that catch or tilt during use.
• Helps restore proper airflow and consistent cooking when racks sit level.
• Visible, functional repair that avoids sliding or sticking when moving trays.

• Fits into existing oven rack slides; remove old rack by sliding out and lifting if needed.
• No tools required for typical replacement; handle with oven mitts if warm.
• Inspect rack stops and guide rails for damage before installing.
• Follow oven manufacturer safety guidelines: disconnect power or ensure appliance is cool before servicing.