Jenn-Air Washer Parts

This touch-up paint restores small chips, scratches and nicks in painted appliance surfaces for a cleaner, like-new appearance. It's ideal for hiding minor cosmetic damage without repainting the whole panel. What it does:

• Covers small chips, scratches and scuffs on painted appliance surfaces
• Helps prevent bare metal exposure that can lead to rusting of small areas
• Restores color and gloss to localized damage for improved appearance
• Applies to control panels, doors and trim where finish is worn

• Shake well before use and apply sparingly with a fine brush, cotton swab or toothpick
• Allow finish to dry fully between light coats for best color match
• Work in a well-ventilated area and avoid inhaling fumes
• Keep out of reach of children and follow local disposal regulations for paint

Size: 26 inches long. F18t8/cw/k26.

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

This is a genuine replacement screw used to secure appliance components. It provides a simple, reliable fastener for reattaching panels, brackets, or assemblies so parts stay properly mounted and stable during operation. What it does

• Secures panels, trim, brackets or small assemblies in place
• Restores proper fastening where a missing or damaged screw causes loose parts or rattling
• Prevents movement that can lead to noise or misalignment of adjacent components
• Used wherever the original screw was removed or lost during repairs

• One replacement screw

• Use the matching screw head and thread engagement; do not force if it does not seat smoothly
• Tighten until snug—avoid overtightening to prevent stripping or cracking plastic parts
• Disconnect power before working on electrical appliances and follow basic safety precautions
• If original screw was rusted, check mating threads for damage before installing new fastener

Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A

Sealer for refrigerant line insulation.

This idler pulley guides and maintains tension on the dryer drive belt so the drum spins smoothly and quietly. Replacing a worn pulley restores proper belt tracking and helps prevent belt wear or breakage. What it does:

• Maintains correct tension and alignment of the drive belt
• Reduces squealing or grinding noises from a worn pulley bearing
• Prevents belt slipping and uneven drum rotation
• Helps avoid premature belt wear or burning rubber smells

• Disconnect power to the appliance before starting any work.
• Access may require removing the dryer front or cabinet panels and releasing the belt; follow your model's service instructions.
• Inspect the belt and drum support for wear and replace if needed while servicing.
• Use basic hand tools.

Size: 1/4 lb.

This replacement light bulb restores visibility inside your appliance so you can quickly see food, settings, and contents. Replace a burned-out or flickering bulb to bring back bright, reliable illumination in compatible models. What it does:

• Provides interior light when the door is opened or the light switch is activated
• Directly replaces a failed, dim, or intermittently flickering bulb
• Helps you see items and controls clearly during use
• Common signs you need this part: light won't turn on, flickers, is very dim, or the bulb is visibly damaged

• 1 light bulb

• Disconnect power (unplug the appliance or switch off the circuit breaker) before starting
• Allow the old bulb to cool completely to avoid burns
• Remove any lens or cover as your model requires; carefully remove the old bulb and handle the new bulb with a clean cloth or gloves
• Do not exceed the bulb type/wattage specified for your model; restore power and test the light

This lid switch assembly kit is the washer's safety interlock. It detects when the lid is closed so the control can allow the machine to spin, helping restore safe, reliable operation when the original switch fails.

• Senses lid closed and enables the spin cycle
• Prevents spinning with the lid open for safety
• Common failure symptoms: no spin or intermittent spin
• Requires pressing or jiggling the lid to run; no audible "click" when closing the lid

• Disconnect power before servicing
• Access the switch under the top/console area; remove the old switch/bracket as designed
• Route wiring along the original path and secure away from moving parts
• Align the actuator so the lid reliably engages the switch; test spin operation before reassembly

A stabilizer bracket that secures and supports internal components to reduce movement and rattle during operation. Helps restore stable alignment so the appliance runs quieter and more reliably. What it does:

• Provides structural support to help keep assemblies aligned and reduce excessive movement
• Dampens vibration and minimizes knocking or rattling noises tied to loose components
• Restores proper fit where a worn or broken bracket allowed shifting or misalignment
• Works as a repair for symptoms like intermittent noise, excess vibration, or parts that sag or shift

• Disconnect power (and water if appliance-specific) before beginning any repair
• Basic hand tools are usually required; refer to your model's service manual for exact steps
• Inspect surrounding parts for wear while replacing the bracket