Kenmore / Sears Dishwasher Panel Parts

This replacement panel restores your appliance's original look while shielding internal components. Install a new panel to replace a dented, cracked, or missing piece and keep the assembly secure, aligned, and protected.

• Covers and protects internal parts while restoring the exterior finish and fit
• Provides the designed mounting surface for trim/handles; helps maintain alignment
• Replace when the panel is dented, cracked, warped, rusted, or mounting tabs are broken
• Helps resolve loose or rattling panels and visible gaps or misalignment

• Disconnect power; turn off water or gas supply if applicable
• Wear gloves and protect finished surfaces; handle carefully to avoid bending or scratching
• Transfer and reuse original screws, clips, insulation, and trim as directed by your service manual
• Fit and alignment before fully tightening fasteners

The Toeplate is an OEM part for Frigidaire dishwashers, specifically designed to fit seamlessly at the bottom of your appliance. This toeplate not only enhances the aesthetic appeal of your dishwasher by hiding the space beneath the appliance but also serves as a protective barrier, preventing debris from getting under the dishwasher.

Causes of a bad toeplate include physical damage such as dents, cracks, or warping, often resulting from accidental kicks or impacts. Additionally, improper installation can lead to a loose or misaligned toeplate, which may compromise its functionality and appearance.

Symptoms of a bad toeplate include:

• Visible damage or deformation.
• Difficulty in fitting or securing the toeplate to the dishwasher.
• Increased noise or vibration due to lack of insulation or support.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Water Level Switch Bracket is an OEM part for Whirlpool dishwashers. This bracket holds the water level switch in place. The water level switch is a part that monitors and regulates the amount of water inside the dishwasher.

Causes of a bad Water Level Switch Bracket can include physical damage that may occur during use or installation, corrosion over time due to exposure to moisture and detergents, or general wear that compromises its ability to securely hold the water level switch.

Symptoms of a bad Water Level Switch Bracket include:

• The dishwasher not filling with the correct amount of water
• Water leaking from the dishwasher if the switch moves out of position and fails to regulate the water level accurately.
• Unusual noises during the fill cycle

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Base Panel is an OEM part for Bosch dishwashers. It serves as a protective cover for the bottom of the dishwasher, shielding internal components from debris, moisture, and damage while also contributing to the appliance's structural stability.

Causes of a bad base panel can include physical damage from impacts, corrosion due to prolonged exposure to moisture, or general wear and tear over time. A compromised base panel can lead to further issues by allowing dirt and water to infiltrate sensitive components.

Symptoms of a bad Base Panel include:

• Visible cracks or holes in the panel
• Water leaking from the bottom of the dishwasher
• Increased noise during operation
• Loose or misaligned panel

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Panel (BLK) is an OEM part for Whirlpool dishwashers. This black exterior panel is designed to provide a sleek and durable front surface for the dishwasher, enhancing its appearance and protecting internal components.

Causes of a bad panel can include physical impacts, scratches, or general wear over time. A compromised panel can affect the aesthetic appeal and may expose internal components to potential damage.

Symptoms of a bad panel include:

• Visible dents, scratches, or cracks
• The panel not fitting securely or aligning properly
• Discoloration or fading of the panel surface
• Difficulty opening or closing the dishwasher door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This lower front toe kick panel restores a clean, finished look at the base of the dishwasher and helps shield the bottom area from debris and bumps. Replace a cracked, dented, or missing panel to secure the opening.

• Covers and conceals the lower access opening at floor level
• Helps protect base components from accidental contact and household debris
• Restores appearance when the original panel is damaged or missing
• Common symptoms: visible gap at the bottom front, loose or rattling kickplate, bent or broken panel

• Disconnect electrical power before servicing
• Open the door to access and remove the mounting screws holding the old panel
• Position the new panel, align tabs/slots, and reinstall screws—do not overtighten
• The panel clears the floor and does not interfere with door operation

Color: Black. Other colors: For white use WP3369614.

This lower front kickplate for dishwashers covers the base opening to protect internal components and complete the appliance's appearance. The almond-finish toe kick helps reduce noise escape and restores a clean look when the original panel is damaged or missing. What it does:

• Covers and protects the lower access area, hiding leveling legs and insulation
• Helps contain sound from the base area
• Restores a clean, finished front appearance
• Replace if the kickplate is cracked, bent, rattling, discolored, or missing

• 1 toe kick panel (almond)

• Disconnect power at the breaker before starting; edges may be sharp
• Open the door to access and remove the mounting screws securing the old panel
• Reuse original screws/insulation; align the new panel and set height using the mounting slots
• Tighten screws evenly and verify the door opens/closes without rubbing the panel

Color: White

Color: White

This finished access panel mounts at the lower front of the dishwasher to cover the service opening. It restores a clean, factory appearance while helping shield internal components from debris and incidental contact. What it does:

• Covers the lower front service opening at the base of the dishwasher
• Helps protect wiring, pump area, and insulation from debris and accidental contact
• Contributes to overall noise containment and proper ventilation as designed
• Replaces a panel that is dented, bent, rusted, rattling, or missing

• 1 finished access panel

• Disconnect power (and water, if necessary) before servicing the appliance.
• Remove mounting screws securing the existing panel and set the old panel aside.
• Position the new panel and secure it with the original hardware; ensure it sits flush and doesn't interfere with door operation.
• Restore power and check for proper fit and vibration-free operation.

This lower toe plate mounts at the base of the dishwasher's front. It covers the gap beneath the door to protect internal components and restore a clean, finished look when the original kick panel is dented, cracked, or missing.

• Covers the open area beneath the door at the base of the cabinet
• Shields wiring, hoses, and internal components from bumps and debris
• Restores a clean, finished front appearance
• Common symptoms: panel is bent, cracked, loose/rattling, or missing

• Disconnect power to the dishwasher before servicing
• Remove the mounting screws securing the existing toe plate and lift it away
• Position the new panel and secure with the existing hardware; do not overtighten
• Verify alignment and door clearance after installation

This kickplate assembly is the lower front panel at the base of the dishwasher. It restores a clean, finished look while helping shield internal components from kicks, dust, and splashes at floor level.

• Covers the lower access opening and completes the cabinet base
• Helps protect wiring, pump, and insulation from debris and impact
• Aids in noise dampening when properly installed
• Replaces panels that are bent, dented, scuffed, or missing
• Common symptoms: loose/rattling panel, visible gap under the door, cosmetic damage

• Disconnect power at the breaker; shut off water if working near supply lines
• Remove existing panel mounting screws and retain hardware for reuse
• Align the new panel and secure with the screws; do not overtighten
• Restore power and test

Inner door panel replaces the interior face of the appliance door, restoring a clean surface and proper support for door components so the door can close and seal as intended. Ideal when the door liner is cracked, dented, or visibly worn. What it does:

• Serves as the interior surface of the door and supports the inner glass or window.
• Provides a mounting surface for latches, seals, and related hardware to help maintain a proper door closure.
• Reduces rattling, visible damage, or interior door gaps that can affect operation.
• Protects internal door components from debris and normal wear.

• Disconnect power and unplug the appliance before starting any repair.
• Use basic hand tools to remove door trim or screws; keep all fasteners for reassembly.
• Handle inner glass and sharp edges carefully—wear gloves and eye protection.
• Refer to the appliance's service manual or OEM instructions for model-specific removal and reinstallation steps.

This is the lower access panel for the appliance's base. It finishes the front opening and shields internal components, helping reduce noise and keep dust and debris away from the motor and wiring.

• Covers the lower service opening beneath the door to provide a clean, finished look
• Helps protect internal components from debris and accidental contact
• Can reduce vibration noise when properly secured
• Replace if the panel is bent, cracked, rusted, missing, or rattles/doesn't stay secured

• Disconnect power; also shut off the water supply
• Support the existing panel while removing mounting screws; retain hardware for reuse
• Position the new panel, align with mounting holes/slots, and reinstall screws—do not overtighten
• Confirm door clearance and that the panel sits flush without interference

Color: White. Includes insulation. Other colors: For almond use WP3384157, for biscuit use WP3384157, for black use WP3379920.