Kenmore / Sears Dishwasher Dishrack

Used on the upper rack track

This dishrack organizes and supports dishes inside the dishwasher during wash cycles. Replacing a damaged rack restores smooth loading, keeps items upright, and helps prevent rust stains or snags from broken tines or flaking rack coating.

• Holds and organizes plates, bowls, and cookware during wash and rinse cycles
• Keeps items spaced and upright to promote spray coverage and drainage
• Slides in and out on the rails when the rack is straight and intact
• Common failure signs: rusting/chipping coating, broken or bent tines, cracked or warped wire frame
• Needed if dishes won't stay put or the rack binds when moving on the tracks

• Disconnect power at the breaker and turn off water before servicing interior parts
• Open the door, extend the rack, and remove rail end caps to release the rack
• Transfer any clip-on components from the old rack to the new rack as needed
• Seat the rack on the rails, reinstall end caps, and check for smooth operation

Restore worn dishwasher racks and help prevent rust stains on dishes. This white rack repair kit covers chipped or exposed rack tines and caps bare metal to reduce corrosion and extend the useful life of your racks.

• Re-coats rusted or chipped vinyl on rack tines to help stop corrosion
• Caps exposed tips to reduce rust transfer, scratching, and snags
• Useful when tine caps are missing or the rack coating is flaking
• Common symptoms: rust on tines, stained dishes, sharp/rough tine ends

• Disconnect power and remove the rack before repair
• Clean and dry affected areas thoroughly before applying coating
• Apply in a well-ventilated area; allow full cure time before using the dishwasher
• Replace the rack if metal is severely corroded or broken

The Lower Dishrack is an OEM part for GE dishwashers. It provides a sturdy shelf for placing pots, pans, plates, and other dishware on the bottom level of the dishwasher interior. The lower dishrack supports dish loads, holding them securely in place during the wash cycles. 

Causes of a failing lower dishrack include long-term wear and tear, corrosion from exposure to water and detergents, damage from improper loading, and loose or broken components.

Symptoms of a bad lower dishrack:

• Difficulty sliding the rack in and out
• The rack getting stuck mid-cycle
• Broken or missing wheels/rollers
• Rust formation
• Bent or misshapen wires

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This durable silverware basket holds forks, knives and other utensils securely during dishwasher cycles so small items stay corralled and clean. Fits into the dishwasher rack to keep cutlery organized and prevent items from falling through. What it does:

• Holds and organizes silverware and small kitchen utensils during wash cycles
• Keeps utensils upright and separated for better cleaning and drying
• Prevents small items from slipping into the dishwasher spray area or drain
• Replaces cracked, broken or missing baskets that allow cutlery to scatter

• No tools required; remove the lower rack and set the basket into the designated rack slots
• Ensure basket snaps or rests securely and does not interfere with rack movement or spray arms
• Inspect basket for cracks or sharp edges before use; discontinue use if damaged
• Always follow the appliance manufacturer's safety and installation instructions

The Dishrack Stop Clip is an OEM component specifically designed for Whirlpool brand dishwashers. This clip functions to hold the upper dish rack in place during washing cycles.

Symptoms of a bad dishrack stop clip can include:

• Movement or vibration of the upper dish rack during washing
• Visible damage, bending or broken tabs on the mounting clip itself  
• Inability to smoothly slide or remove the upper dish rack

Causes of a bad dishrack stop clip usually stem from normal wear and tear over extended use. Overtight loading of dishes could also put excessive stress on the clip.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This is a replacement dishwasher rack assembly with factory-installed wheels. It restores smooth sliding and safe loading when the original rack is bent, rusted, or missing rollers—helping the rack glide properly and keep items positioned during the wash.

• Holds and organizes dishes, glasses, and cookware during cycles
• Integrated wheels ride on the tracks for easy loading and unloading
• Replace if tines are rusted/broken, wheels are cracked or missing, or the rack derails
• Helps prevent items from tipping and maintains consistent spray coverage

• Disconnect power to the dishwasher before servicing
• Open the door, extend the rack, release any rail end-stops, and remove the old rack
• Transfer any removable accessories from the old rack to the new one, if needed
• Slide the new rack onto the rails and reinstall end-stops; verify smooth operation

The Track is an OEM part for Whirlpool dishwashers. It serves as the track or rail that allows the dishrack to glide smoothly in and out of the dishwasher during loading and unloading. The track is precision-engineered to provide smooth, controlled movement of the dishrack. It includes all necessary mounting brackets and attachments to facilitate simple installation.

Causes of a bad track can include scratches, dents or other damage due to impact or repeated use over time. The roller or wheel components may also become worn down or jammed, hindering proper movement.

Symptoms of a bad track include:

• The dishrack not rolling out fully or getting stuck partway
• Scratching or scraping noises when moving the dishrack
• Difficulty pushing the dishrack in and out
• The dishrack tilting or becoming unbalanced during movement

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This rack assembly restores a sturdy, properly fitting rack inside your appliance so items are supported and move smoothly on the rails. Replace a bent, rusted, or missing rack to keep loading safe and performance consistent. What it does:

• Provides a stable surface for loading items during use
• Aligns with factory rails for correct fit and smooth in/out movement
• Replaces racks that are bent, warped, broken, rusted, or missing
• Helps prevent snags or stains caused by damaged or flaking rack wires

• One rack assembly

• Disconnect power; allow it to cool completely
• Pull the old rack straight out of the rails; if your model uses rack stops or clips, transfer them from the original
• Slide the new rack into the rails until fully seated
• Verify smooth travel and proper clearance before use

The Lower Dishrack Assembly is an OEM part for Bosch dishwashers. This assembly holds the dishes, utensils, and other items to be cleaned on the lower level of the dishwasher. It is designed to slide in and out smoothly, providing easy access for loading and unloading.

Over time, the lower dishrack can become worn out or damaged due to frequent use, exposure to high temperatures, and the weight of the items placed on it. Causes of a bad lower dishrack include broken or missing wheels, rust, and damage to the rack's frame or coating.

Symptoms of a bad lower dishrack include:

• Difficulty sliding the rack in and out
• Rust or corrosion on the rack
• Broken or missing tines
• Items not staying in place during the wash cycle

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This MultiFence is a multi-position rack fence that mounts to the rack to support and organize dishes, lids, and bakeware. It helps keep items upright and in place so cycles run smoothly and cleaning performance stays consistent. What it does:

• Attaches to the rack and flips/locks to secure items of different sizes
• Helps prevent plates, lids, and trays from tipping or sliding during operation
• Replaces a fence that is cracked, warped, missing, or won't stay in position
• Common symptoms include dishes falling over, rattling during cycles, or poor results from shifted loads

• One MultiFence rack fence

• Disconnect power to the appliance; turn off water supply if servicing a dishwasher
• Pull the rack out; release the retaining tabs or clips to remove the old fence
• Align and snap the new fence onto the rack wires; ensure it pivots and locks properly
• Reinstall the rack and verify smooth operation

Note: There are four wheel assemblies includes with this rack. The flexible tine rows are not included. This is a lower dishrack assembly for a dishwasher. This part holds the dishes during the washing and drying cycles. Note that this is only the lower dishrack assembly and the upper dishrack assembly is sold separately. Over time, the lower dishrack assembly may begin to rust or the coating may wear off. It is also possible that sections of the part could break due to degradation over time. If this happens, the entire lower dishrack assembly will need to be replaced. The lower dishrack assembly is compatible with dishwashers that are manufactured by the Kenmore, KitchenAid, and Whirlpool brands. It comes straight from the manufacturer and is sold individually. It's a genuine, high-quality, and durable OEM part.