Need Help?
Call or text
Replacement upper rack adjuster kit for dishwashers. Includes left and right side adjusters with rollers. Needed when original adjusters crack or break.
The repair kit has everything needed for both sides of the rack but there were no instructions so it took me some time to figure out how it all mounted on the basket. The original design was totally different than the repair kit so it would have been very beneficial to have at least a diagram that showed how everything fit together. That being said, once I figured out how all the parts fit, then it was a very easy repair. You won't reuse any of the old parts except for the end caps that snap... Read more
Replacement upper rack adjuster for dishwashers. Mounts to the upper rack to adjust height and provide flexible loading. Replace if cracked or broken.
I bumped into my KitchenAid dishwasher and the upper rack adjuster cracked. There was already a crack on the notch of the housing where the handle (lever) sits. In addition, the positioner popped out and I couldn't find it. So, I bought the three parts from AppliancePartsPros online. It arrived in about a week. The repair was fairly simple, but it still took about 45 minutes because I didn't want to crack the assemblies. For the housing, use a small slotted screwdriver to carefully... Read more
Replaces cracked, broken, or missing dishwasher rack stop clips. Secures upper or lower dishrack to track rail, preventing rack from sliding out too far.
My discharge would not empty after a wash cycle and I always had gross gray water left in the bottom approx 3" deep? After doing the obvious things of checking the simp for garbage, and checking that the discharge hose wasn't blocked, I removed my discharge pump ( not too hard to do) and tested. My pump which did run and turn the impeller. However, the pump evidently had weakened with time and weakened and could no longer pump the waste water up hill to the "T" connection under the sink. A... Read more
Replaces broken or worn dishwasher upper rack adjuster assembly. Includes wheels and mounting hardware for smooth rack adjustment and gliding action.
I replaced the adjusters on both sides (since two rollers broke off on one and one broke off on the other). Replacement was easy, just remember to keep the clips from the original adjusters. Take the clips off, remove the adjuster, replace with the new adjuster, and replace the clips. The new adjuster comes with the rollers already attached so no need to keep the ones from when plastic axle broke on the original adjusters. Read more
Secures the dishwasher rack to prevent it from rolling out too far. Replace this clip if it's cracked, broken, or missing to keep your rack stable.
Replaced wheel assembly because prongs were broken and replaced track because wheel assemblies were rolling out from the track when extended. Read more
Replacement pivot for dishwasher upper rack tine rows. Allows tines to fold down for taller items. Needed when pivot is broken, cracked, or missing.
Ordered a new one. It took about 10 seconds to install. Now it’s like brand new. Read more
Clips onto the upper dishrack to hold the height adjuster assembly in place for balanced operation. Replace if cracked, broken, or missing.
Upper dishrack assembly for dishwashers. Holds dishes during wash cycles. Replace when rack shows rust, peeling coating, broken tines, or structural damage.
To say using Appliance Parts Pros made things as simple as it gets, is an understatement. I was able to order the parts simply by using their website and having my dishwasher make and model number. Images of the parts make confirming the order even better. They have an on line question/answer cue if needed and even offer a call in for advice number. Once the order arrived, I verified the parts and began installation. Take a few pictures of the appliance from different angles before you start.... Read more
Right-hand track assembly that guides the upper dishwasher rack as it slides in and out. Replace if cracked, broken, or ball bearings fall out.
Ordered numerous replacement parts. Started with the tracks which required pulling the washer out of the cabinet to reach the screws. Pushed it back in and re-secured. Then stared on the rack and replaced the rack adjusters and various clips. Everything is straight forward and easy to replace. I originally called a local repair place to have them repair it. They came out and said they needed to order parts and they would call back. A week went by and I followed up with them. Had to leave... Read more
Left-hand track assembly guides and supports your dishwasher's upper rack as it slides. Replace if cracked, broken, or ball bearings have fallen out.
Replacement lower dishrack for dishwashers. Holds dishes, pots, and pans during wash cycles. Replace if cracked, rusted, or tines are broken or missing.
I ordered a replacement part from AppliancePartsPros.com, however the exact part for my Kitchen Aid dishwasher had been discontinued. There were two differences between the original and replacement part. First, the original rack had two adjustable tine rows, but the replacement only had one. I was only able to attache one of them to the new rack. This didn't present any issue other than having less flexibility in customizing the configuration for loading large items on the rack. The second... Read more
Secures the end of the dishwasher rack slide rail. Replace if cracked, broken, or missing to prevent racks from sliding off track or misaligning.
Replaced the pump drain assembly Read more
Upper dishrack track for dishwashers. Guides the top rack for smooth sliding. Replace if cracked, warped, or causing rack to fall when pulled out.
Replace your dishwasher's lower dishrack assembly if it's rusted, cracked, or has broken tines. This gray rack holds dishes securely during wash cycles.
I very seldom respond to requests for feedback like this but definitely feel moved to do so in this case. When our 8 year old dishwasher started acting up my initial reaction was to simply replace it. I wasn't sure what was wrong, nor if I would be able to find the right part once I did figure out the problem. The troubleshooting advice on this website was spot on and I quickly figured out what needed to be replaced. The repair videos were easy to follow and the parts were here two days... Read more
Replacement silverware basket for dishwashers. Holds utensils securely during wash cycles. Replace if cracked, broken, or has holes causing items to fall.
Purchased a replacement basket. First I visited the Sears website for a replacement part since the dishwasher was a Kenmore, but Sears did not carry the same basket that was original to the dishwasher. Their replacement was an open basket without dividers. You are the only company that I found that carries the exact part for the model of dishwasher. An vanother pleasing experience I had with AppliancePartsPros.com is that I received the replacement within 5 days of placing the order. It... Read more
Lower rack assembly for dishwashers. Replaces racks with rust, corrosion, broken wheels, or worn coating. Includes rollers for smooth sliding.
Replaced the rack. Had to take some of the old parts that were still good and snap them into place.. pretty easy. Read more