Kenmore / Sears Dishwasher Valve

Fix leaking dishwasher or water overflowing onto the floor. This float assembly rises with water level to prevent overfills. Easy 5-10 minute repair.

The Float is an OEM part for Bosch dishwashers. This float senses water levels inside the dishwasher, signaling the inlet valve to refill when needed.

Causes of a float malfunctioning can be mineral deposits accumulating and weighing it down over time, or cracks in the plastic housing allowing water in.

Symptoms of a bad float include:

• The dishwasher not filling or filling slowly
• Error codes related to fill issues
• Improper water levels impacting wash results

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Fix dishwasher overfilling or not filling with water by replacing the float assembly. Common issue with sticky buildup preventing proper operation.

Fix dishwasher overflows or underfilling with a new water level float. This part regulates filling by rising with water to signal the switch.

If your dishwasher shuts off mid-cycle or leaks water, a warped or stuck overfill float may be the cause. This 5-minute fix restores proper fill control.

Converting your portable dishwasher to built-in? This conversion kit includes all mounting hardware and adapters needed for permanent installation.

This small check ball helps control water flow inside the refrigerator's water/ice system to prevent backflow and ensure proper filling. It restores reliable water seating where valves or distributor ports use a ball-style check. What it does:

• Acts as a one-way seal to stop water from flowing backward into the supply line or valve bore
• Helps the ice maker and dispenser fill correctly by allowing water in but not back out
• Common symptom: intermittent or incomplete ice maker fills
• Common symptom: slow or continuous dripping from dispenser or valve area

• Shut off water supply and unplug the appliance before starting
• Small part — handle carefully and note orientation/seat before removal
• Inspect valve bores and seals for debris; clean area before installing new check ball

The Impeller Jug is an OEM part for Bosch dishwashers. Located inside the wash chamber, the impeller jug is responsible for evenly distributing water throughout the dish rack during the wash cycle. It features strategically placed holes and channels that work with the spray arms to direct water flow and ensure all dishes receive thorough coverage. 

Symptoms of a bad impeller jug include:

• Incomplete cleaning even on short or heavy wash cycles  
• Dirty dishes remaining at the end of the cycle
• A buildup of food or grime deposits inside the wash chamber
• Off-balanced or excessive noise levels during washing

Causes of failure can be mineral or scale buildup inhibiting water flow, cracked or damaged casing allowing leaks, or worn impeller fins no longer efficiently dispersing water. Over time, hard water deposits and normal use can degrade performance. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers. 

Replacement water inlet valve that controls water flow into the refrigerator's dispenser and ice maker, restoring proper filling and preventing overflows. Direct-fit design replaces the original valve on compatible Whirlpool refrigerators. What it does:

• Regulates water flow from the household supply to the refrigerator dispenser and ice maker.
• Opens when the dispenser or ice maker calls for water and closes to stop flow and prevent overfilling.
• Common symptoms: no water from the dispenser, slow/weak fill, ice maker not filling, or water leaking at the valve.
• Designed to match the original valve's function and plumbing connections for straightforward replacement.

• Disconnect power to the appliance and shut off the water supply before starting any work.
• Use basic hand tools to remove and reinstall mounting screws and water line fittings; support lines to avoid stress on fittings.
• Inspect and replace any damaged O-rings or supply tubing; tighten fittings securely but avoid overtightening.
• After installation, turn water on slowly, check all connections for leaks, then restore power and verify dispenser/ice maker operation.

Fix dishwasher overflows or won't fill issues. This water level float detects proper fill levels. Replaces broken or stuck floats causing drainage problems.

Fix dishwasher overfilling or not filling properly with a new float dome. Protects the float sensor for accurate water level control. Easy 15-minute repair.

This water inlet valve controls water flow to the refrigerator's ice maker and dispenser, restoring proper water delivery when the system won't fill or dispense. Direct-fit replacement that helps stop leaks and restore function. What it does:

• Opens and closes to let water into the ice maker and dispenser when signaled
• Stops water flow when the fill cycle or dispense cycle ends
• Common part to replace for slow/no ice production or no water from dispenser
• Replaced when valves leak or water lines fail to pressurize

• Disconnect power and shut off the water supply before starting work
• Verify tubing connections and electrical connector orientation before reassembly
• Inspect supply lines and gaskets; use proper replacement fittings if damaged

Fix a dishwasher that won't fill with water or fills slowly with this water inlet valve. Common repair for no water flow issues. DIY-friendly fix.

Fix a dishwasher that won't fill with water or fills too slowly with this water inlet valve. Moderate DIY repair requires basic tools and plumbing skills.