Kenmore / Sears Freezer Parts

This refrigerator door gasket creates an airtight seal around the door to keep cold air in and warm air out, helping maintain proper temperature and energy efficiency. Replacing a worn gasket restores a reliable seal and prevents frost or moisture issues.

• Seals the perimeter of the refrigerator door for consistent cooling
• Helps reduce frost, condensation, and temperature swings
• Common symptoms include doors not sealing well, warm spots, or excess moisture

• Unplug the appliance before service
• Soften the gasket in warm water to improve flexibility and fit
• Clean and inspect the door channel; start seating the gasket at the corners
• After installation, close the door and check for uniform contact around the seal

This is a compressor start relay device that helps the compressor motor start up and run efficiently. It provides the initial electrical boost needed to get the compressor running and then disengages once the motor reaches operating speed. Replace this part if the refrigerator is not cooling, the compressor clicks on and off repeatedly, or you hear a buzzing sound coming from the back of the unit.

Replacement shelf support bracket for freezers. Secures and stabilizes freezer shelves. Replace if broken, cracked, or missing due to heavy loads or age.

Seals the freezer door perimeter to maintain airtight closure. Replace when worn to restore proper seal, stabilize temps, and reduce frost buildup.

This temperature control knob replaces a worn or missing knob so you can easily adjust the cold-control setting. Restores smooth, precise temperature adjustments and a clean, factory look. What it does:

• Attaches to the cold-control (thermostat) shaft to change the temperature setting
• Provides secure grip and pointer alignment for accurate selections
• Typical failure symptoms: cracked or missing knob, stripped hub, or a knob that slips or won't turn the control

• 1 temperature control knob

• Disconnect power before servicing
• Pull the old knob straight off the shaft; avoid prying at an angle to prevent shaft damage
• Align the shaft shape with the new knob and press firmly until fully seated
• The pointer aligns with the control graphics after installation

Replacement screw that secures brackets, shelves, trim, panels, and covers inside your appliance. Install when the original is missing, stripped, or corroded.

This door rack mounts to the inside of the refrigerator or freezer door to hold small items securely. Replace a cracked or missing rack to restore door storage and prevent items from falling when the door opens and closes.

• Provides additional storage on the inner door for jars, condiments, and small items
• Helps keep contents organized and stable during door movement
• Common symptoms: broken or missing rack, items falling from the door, reduced storage space
• Restores original fit and function when the existing rack is damaged

• Unplug the appliance before servicing
• Remove items from the affected door area
• Lift or release the old rack from the end supports/slots; seat the new rack fully into the same supports
• Confirm the rack is secure before reloading and avoid overloading to prevent damage

Freezer won't shut off or stop cooling? This temperature control thermostat cycles the compressor on and off to maintain set temps. DIY repair.

This light socket holds the interior appliance bulb and connects it to the unit's wiring. Replace a damaged or loose socket to restore dependable cabinet lighting when the door is opened.

• Secures the interior light bulb and provides reliable electrical contact
• Supplies power to the lamp when the door switch closes
• Helps resolve flickering or intermittent lighting from a worn or heat-damaged socket
• Common symptoms: light won't turn on, bulb won't seat or stays loose, visible charring at the socket

• Disconnect power to the appliance before servicing
• Remove the lens/cover and bulb; release the socket from its mounting
• Transfer wires one at a time to the new socket and ensure snug connections
• Reinstall bulb and cover, restore power, and test; use the bulb type/wattage specified by the manufacturer

This electronic control board is the freezer's central control module. It processes sensor inputs and user settings to run the cooling system and alerts. Replacing a failed board helps restore reliable operation and accurate temperature management. What it does:

• Controls compressor and evaporator fan operation to maintain the set temperature
• Interprets thermistor input and applies control logic to regulate cooling
• Coordinates features such as alarms and, on electronic models, defrost cycles
• Common symptoms include the unit not running or powering up, warming or unstable temperatures, unresponsive or erratic controls/display, or excessive frost buildup

• Disconnect power before servicing; handle the board with ESD precautions
• Access the control housing, note wire locations, and transfer connectors one at a time
• Secure the replacement board and reuse original mounting hardware and any reusable trim/overlay as applicable
• Restore power, set temperatures, and allow up to 24 hours for stabilization

Lower basket organizes items in the bottom of your freezer. Replace a bent, broken, or missing basket to restore tidy storage and easier access to frozen food.

Replacement screw for securing panels, brackets, and internal components in freezers and refrigerators. Use to replace missing or stripped hardware.

This is a compressor start relay that helps the compressor motor start up by providing the initial surge of power needed. It is a small device that typically mounts directly onto the compressor. Replace this part if the compressor fails to start, runs intermittently, or if you hear repeated clicking sounds coming from the back of the unit.

This slide basket is a direct-fit replacement that restores smooth slide-out access and secure storage for a refrigerator drawer. It helps keep foods organized and prevents items from shifting or falling when you open the drawer. What it does:

• Provides a slide-out basket for easy access to refrigerated or frozen items.
• Keeps stored items contained and organized on a removable platform.
• Replaces cracked, warped or damaged baskets that cause sticking, catching or uneven sliding.
• Helps prevent items from falling when pulling the drawer open.
• Works with the drawer's slide/track system to maintain alignment and function.

• Disconnect power to the appliance before starting any service.
• Remove food and lower shelves or drawers to access the basket; follow your owner's manual for removal steps.
• Inspect drawer slides and rails for damage before installing the new basket; align slides and test for smooth operation.

This slide rail supports a freezer basket or drawer, allowing it to glide smoothly in and out of the freezer compartment. It mounts to the interior side wall of the freezer and keeps the basket properly aligned. Replace this part if the freezer basket sticks, tilts, derails, or no longer slides freely.

Touch-up paint for appliances to cover scratches, chips, and worn areas on exterior surfaces. Restores appearance of refrigerators, ranges, and more.