Kenmore / Sears Freezer Parts

Replacement door handle for freezers. Installs on the exterior door to provide a secure grip for opening and closing. Ideal when original is cracked or broken.

Secures interior trim and panels in refrigerators and freezers. Replace when trim becomes loose or rattles. Confirm fit with your model number.

Start relay for refrigerator compressors that helps the compressor begin running at power-up. Replacing a failed relay can restore normal starting behavior and resolve common startup symptoms. What it does

• Provides the initial start current path to the compressor during startup.
• Allows the compressor to reach running speed, then drops out once the motor is running.
• Common symptoms a bad relay may cause: compressor clicking, humming without starting, intermittent cooling or frequent cycling.
• Installed as the electrical component used only on compatible compressor assemblies.

• Disconnect power to the appliance before servicing to avoid electrical shock.
• Access the relay at the compressor; remove and replace the relay only after confirming diagnostics.
• Dispose of the old electrical part per local regulations.

Touch-up paint for appliances to cover scratches, chips, and worn areas on exterior surfaces. Restores appearance of refrigerators, ranges, and more.

Interior light not working? This light socket provides the electrical connection for your freezer bulb. Simple DIY fix restores compartment lighting.

Replacement slide for freezer wire baskets. Attaches to basket bottom for smooth gliding along tracks. Replace when broken, cracked, or missing to restore alignment.

Rubber grommet kit that mounts and cushions the compressor. Replace worn, cracked, or damaged grommets to restore proper support and isolation.

Fix a clicking compressor or refrigerator that won't cool. This start relay and overload assembly restores compressor startup. DIY repair in 10-15 minutes.

This defrost heater melts frost and ice buildup on the evaporator so your freezer can run efficiently and maintain proper cooling. It's a direct replacement heater element used in frost control during automatic defrost cycles. What it does

• Heats the evaporator coil during the defrost cycle to remove frost and ice buildup.
• Helps restore normal airflow and cooling when frost is blocking the evaporator.
• Common symptom: visible ice buildup on evaporator or frost accumulation inside the freezer.
• Common symptom: reduced cooling performance or long run times due to iced coils.

• Disconnect power to the appliance before starting any repair.
• Access the evaporator by removing the back panel inside the freezer; follow the OEM repair diagram.
• Handle the heating element carefully to avoid bending or damaging the coil; ensure proper routing and clip placement.
• After installation, restore power and test continuity of the heater with a multimeter if needed.

This is a small air baffle breather valve that helps equalize air pressure between the interior compartment and the outside environment. It allows air to pass through while helping maintain proper temperature regulation. Replace this valve if you notice excessive frost buildup, difficulty opening the door shortly after closing it, or unusual air pressure issues inside the unit.

This compressor overload is a thermal/protective device that helps prevent compressor damage by cutting power when the motor overheats or draws excessive current. It restores normal operation once conditions return to safe levels. What it does:

• Protects the refrigerator compressor from overheating and electrical overloads
• Works with the compressor start relay to help the motor start and run properly
• Common symptom linkage: replaces a failed overload when the compressor hums but won't start
• Stops compressor cycling or prevents repeated trips that cause cooling loss

• One compressor overload (single piece as shown)

• Disconnect all power before replacing to avoid shock or injury
• Handle terminals carefully and reconnect matching terminal positions
• Replace only with the same part number or equivalent
• If compressor still won't start after replacing the overload, check the start relay and compressor condition.

Fix a refrigerator that won't cool or start. This compressor start relay helps your compressor run reliably and prevents clicking sounds. Easy DIY repair.

Graphite spray paint for appliance touch-ups. Covers chips, scratches, and scuffs on dryer drums, washer panels, and exterior surfaces. Restore finish.

Freezer stopped making ice? This ice maker assembly restores automatic ice production. Connects to existing water supply and wiring for reliable operation.

The refrigerator door tilt-out shelf end cap covers and secures the left end of adjustable door storage bins that tilt forward for easy access. Replace when the end cap cracks, breaks, or no longer securely holds the shelf in position.

Right-side end cap for refrigerator tilt-out door bin. Replaces cracked, broken, or missing end piece. Restores secure mounting and smooth pivoting.